Canon Eos Rebel T5 1200 Instruction Manual

231
B Shooting Information Display
 Highlight Alert
When the shooting information is displayed, any overexposed areas of the 
image will blink. To obtain more image detail in the overexposed areas, set 
the exposure compensation to a negative amount and shoot again.
 Histogram
The brightness histogram shows the exposure level distribution and overall 
brightness. The RGB histogram is for checking the color saturation and 
gradation. The display can be switched with [
x2: Histogram disp].
[Brightness]...

COPY  

233
9
Post-ProcessingImages
After taking a picture, you can apply a Creative filter or 
resize the image (reduce the number of pixels).
 The camera may not be able  to process images taken with 
another camera.
  Post-processing images as desc ribed in this chapter is not 
possible while the camera is connected to a computer via the 
interface cable.
COPY  

234
You can apply the following Creative filters to an image and save it as a 
new image: Grainy B/W, Soft focus, Fish-eye effect, Toy camera effect, 
and Miniature effect.
1Select [Creative filters].
 Under the [ x1] tab, select [ Creative 
filters ], then press < 0>.
X An image will be displayed.
2Select an image.
  Select the image you want to apply a 
filter to.
  By pressing the < Hy> button, you 
can switch to the index display and 
select an image.
3Select a filter.
  When you press < 0>, the...

235
U Applying Creative Filters
5Save the image.
  Select [ OK] to save the image.
  Check the destination folder and 
image file number, then select [ OK].
  To apply filters to another image, 
repeat steps 2 to 5.
  To return to the menu, press the 
 button.
 When shooting  1+73  or 1  image, a filter effect will be applied to 
the  1  image and the image will be saved as a JPEG image.
  If an aspect ratio was set for a  1 image and a filter effect is applied to 
it, the image will be saved in the...

U Applying Creative Filters
236
  Grainy B/W
Creates a grainy black-and-white photo. You can change the black-
and-white effect by adjusting the contrast.
  Soft focus
Gives the image a soft look. You can change the degree of softness 
by adjusting the blur.
  Fish-eye effect
Gives the effect of a fish-eye lens. The image will have a barrel-type 
distortion.
Depending on the level of this filter effect, the area trimmed along 
the periphery of the image changes. Also , since this filter effect will...

237
You can resize an image to make the pixel count lower and save it as a 
new image. Resizing an image is possible only with JPEG 3/4 /a /b  
images.  JPEG c and RAW images cannot be resized.
1Select [Resize].
  Under the [x 1] tab, select [Resize ], 
then press < 0>.
X An image will be displayed.
2Select an image.
  Select the image you want to resize.
  By pressing the < Hy> button, you 
can switch to the index display and 
select an image.
3Select the desired image size.
  Press < 0> to display the...

S Resizing JPEG Images
238
Resize Options According to Original Image Size
The image size displayed in step 3 on the preceding page, such as 
[***M ****x**** ], has a 3:2 aspect ratio. The image size according to 
aspect ratios is shown in the table below.
The asterisked image-recording qualit y figures do not exactly match the 
aspect ratio. The image  will be cropped slightly.
Original Image 
SizeAvailable Resize Settings
4 abc
3 kkkk
4
kkk
a
kk
b
k
c
Image Sizes
Image 
QualityAspect Ratio and Pixel...

239
10
Printing Images
 Printing  (p.240)
You can connect the camera directly to a printer and print 
out the images on the card. The camera is compliant with 
“ w PictBridge”, which is the standard for direct printing.
  Digital Print Order Format (DPOF)  (p.249)
DPOF (Digital Print Order Format) enables you to print 
images recorded on the card according to your printing 
instructions such as the image selection, quantity to print, 
etc. You can print multiple images in one batch or give the 
print...

240
The direct printing procedure can be performed entirely with the camera while you look at the camera’s LCD monitor.
1Set the camera’s power switch to 
.
2Set up the printer.
 For details, refer to the printer’s 
instruction manual.
3Connect the Camera to the 
Printer.
 Use the interface cable provided with 
the camera.
  Connect the cable to the camera’s 
digital terminal with the cable plug’s 
 icon facing the front of the 
camera.
  To connect to the printer, refer to the 
printer’s instruction...