Canon cinema EOS1D C User Manual
Here you can view all the pages of manual Canon cinema EOS1D C User Manual. The Canon manuals for Cinema are available online for free. You can easily download all the documents as PDF.
Page 41
41 Checking Image Transfer History On the [Image sel./transfer] screen, you can check the number of images to be transferred as well as the transfer history of images in the memory card. Specifically, you can check the number of images classified as [Images failed trans.] and [Images transferred]. Checking the Transfer History of Memory Cards
Page 42
42 Images transferred to the FTP server are stored in the following folder as specified in the FTP server settings. Under the default settings of the FTP server, images are stored in [C drive] [Inetpub] folder [ftproot] folder, or in a subfolder of this folder. If the root folder of the transfer destination has been changed in the FTP server settings, ask the FTP server administrator where images are transferred. Open the [Macintosh HD] [Users] folder. The folder where images are stored is...
Page 43
43 3 Remote Capture Using EOS Utility You can use EOS Utility to shoot remotely over a wired LAN. In addition to remote capture, almost all EOS Utility camera operations except firmware updating are supported, because this option utilizes a wired network instead of a USB cable. Mac Versions of EOS Utility The EOS-1D X’s wired LAN functions cannot be used in Mac OS X 10.8.0 or 10.8.1.
Page 44
44 These instructions are continued from Chapter 1. With EOS Utility, you can use Pairing Software (EOS software) to establish a connection between the camera and a computer. Pairing Software is installed automatically with EOS Utility. The configuration procedure below uses Windows 8.1 as an example. Users of EOS Utility Ver. 2.13 or earlier: Go to step 3. 1Start EOS Utility on the computer. 2In EOS Utility, click [Pairing over Wi-Fi/LAN]. Select [Ye s] if a message is displayed regarding the...
Page 45
45 Configuring EOS Utility Communication Settings 3Select [OK]. First, the pairing screen is displayed. Turn the dial to select [OK]. When you press , the following message is displayed. “******” represents the last six digits of the MAC address of the EOS-1D X you are connecting. Users of EOS Utility Ver. 2.14 or later: Go to step 6. 4Start the pairing software. Normally, it is installed in the same location as EOS Utility. XWhen the pairing software starts up, an icon is displayed in the...
Page 46
46 Configuring EOS Utility Communication Settings 5Click the pairing software icon. XDetected cameras are listed. If a camera is already connected, it is not displayed in the list. 6Select the camera to connect to and click [Connect]. If multiple cameras are displayed, identify the camera to connect to by its [MAC address] or [IP address]. You can check the [MAC address] and [IP address] by accessing [Confirm settings] in the menu (p.70). 7Select [OK]. When the camera detects the computer on...
Page 47
47 Configuring EOS Utility Communication Settings 8Save the settings. Press and turn the dial to select the set number, and then press . After you turn the dial to select [OK] and press , the connection wizard closes and EOS Utility starts up. XThe < LAN> lamp on the camera lights up in green. The EOS Utility network settings are now complete. There is no need to complete pairing again if you continue using a particular camera and computer together after pairing without changing the...
Page 48
48 For EOS Utility instructions, refer to the Software Instruction Manual (PDF). Using EOS Utility The motion of moving subjects may not be displayed smoothly depending on the image transmission speed of the wired LAN.
Page 49
49 4 Remote Capture Using WFT Server Using a web browser, you can view images recorded on a memory card in the camera and download them to a computer. Additionally, you can shoot remotely over a wired LAN. Note that bulb, mirror lockup, and movie shooting are not supported.
Page 50
50 These instructions are continued from Chapter 1. Press and turn the dial to select the set number, and then press . Press again. After the connection wizard closes, the display will return to the menu screen. XThe lamp on the camera lights up green. Enter a login name and password to access the camera from a computer. The login name and password you specify here are used on the computer when connecting to the camera. 1 Turn the dial to select [Set up], and then press . Configuring WFT...