Canon cinema EOS C100 Mark II User Manual

181
Displaying the Status Screens
[/ Data 3/3] Status Screen ( mode only)
[Network Settings 1/9] Status Screen
1
3
2
5
67
8
4
1 White balance R/B gain (A118)
2 Color correction (A118)
3 Area A settings (phase, chroma, area and Y level) 
(A118)
4 Area A revision settings (level and phase) 
(A118)5 Area B settings (phase, chroma, area and Y level) 
(A118)
6 Area B revision settings (level and phase) 
(A118)
7Setup level (A118)
8 Clip exceeding 100% (A118)
1
1 Camcorder’s MAC address  

Displaying the Status Screens
182
[Network Settings 2/9], [Network Settings 3/9] Status Screens
Connection settings of the current network connection (A145)
[Network Settings 4/9], [Network Settings 5/9] Status Screens
TCP/IP settings of the current network connection (A150)
1
2
3
4
5
6
1 Network configuration name (A151)
2Connection type
3 SSID (network name)4 Authentication and encryption method
5WEP index key
6 Wi-Fi channel
1
2
3
4
5
6
1 IP address assignment method
2 IP address
3 Subnet mask
4...

183
Displaying the Status Screens
[Network Settings 6/9] Status Screen
[Network Settings 7/9], [Network Settings 8/9], [Network Settings 9/9] Status Screens
* The password itself will not be displayed.
1
2
Browser Remote settings (A153)
1 Port number 2 Camcorder ID
1
2
3
4
5
6
7
8
FTP server settings (A158)
1 FTP server (host) name
2User name
3 Password protection*
4Port number5 Destination folder on the FTP server
6 Passive mode
7 Create new folders by transfer date
8 Handling of same-named files 

Displaying the Status Screens
184
[GPS Information Display] Status Screen ( mode only)
GPS information (A104)
4
3
1
2
5
1Latitude
2Longitude
3Elevation4 UTC (coordinated universal time) date and time
5 Satellite signal strength 

185
Troubleshooting
Troubleshooting
If you have a problem with your camcorder, refer to this section. Consult your dealer or a Canon Service Center 
if the problem persists.
Power source
The camcorder will not turn on or it turns off by itself.
- The battery pack is exhausted. Replace or charge the battery pack.
- Remove the battery pack and reattach it correctly.
Shortly after turning it on, the camcorder turns off on its own.
- You are using a battery pack that is not compatible for use with this...

Troubleshooting
186
Changing between recording (ÜREC) and record pause (STBY) takes longer than usual.
- When the SD card contains a large number of clips, some operations may take longer than usual. Save your clips 
(A143) and initialize the SD card (A42). Alternatively, replace the SD card.
The camcorder cannot record to an SD card properly.
- This may occur as recordings are made and deleted over time. Save your clips (A143) and initialize the SD card (A42).
After using the camcorder for a long time,...

187
Troubleshooting
 appears in red on the screen.
- In   mode, when [Other Functions] > [Fan] is set to [Automatic], the cooling fan will start automatically (  
appears on the screen).
 appears on the screen.
- The camcorder and lens cannot communicate normally. Clean the lens’s contacts and reattach the lens.
Picture and Sound
The OLED screen is too dark.
- Adjust the brightness with the [OLED/VF Setup] > [OLED Setup] > [Brightness] setting. To make the screen brighter 
temporarily, set [OLED/VF...

Troubleshooting
188
The optional RC-V100 Remote Controller or commercially available remote control does not work.
- Make sure that the [Other Settings] > [REMOTE Term.] setting is set to [RC-V100] when using the optional RC-V100 
Remote Controller or [Standard] when using a commercially available remote control.
- When [Camera Setup] > [/ CINEMA Locked] is set to [On], a protected custom picture file is selected, or no custom 
picture is selected, custom picture settings cannot be adjusted using the...

189
Troubleshooting
The Browser Remote or Playback via Browser screen is not displayed correctly on the Web browser.
- The device, operating system or Web browser used may not be supported. For the latest information about supported 
systems, visit your local Canon Web site.
- Enable JavaScript and cookies in your Web browser's settings. For details, refer to the help modules or online 
documentation of the Web browser used.
Using the Playback via Browser application, playback on a Wi-Fi-enabled...

Troubleshooting
190
Cannot acquire battery information   Continue using this battery pack?
- You attached a battery pack that does not bear the Intelligent System mark.
- If you are using a battery pack that bears the Intelligent System mark, there may be a problem with the camcorder or 
battery pack. Consult a Canon Service Center.
Cannot play back
- The file control information is corrupted or there was a decoder error. Turn off the camcorder and back on again. If this 
does not solve the problem,...