Brother Mfc 8220 User Manual

OPTIONAL ACCESSORIES   13 - 5
Before starting installation
Be careful when handling the NC-9100h. There are many delicate 
electronic components that are susceptible to damage from static 
electricity. To avoid such damage, use the following precautions 
when handling the board.
■Leave the NC-9100h in its anti-static bag until you are ready to 
install it.
■Make sure that you are adequately grounded before touching the 
NC-9100h. Use an anti-static wrist strap and a grounding mat if 
possible. If you do...

13 - 6   OPTIONAL ACCESSORIES
Step 1: Hardware installation
WARNING
■DO NOT touch the surface of the main board within 15 minutes 
after turning off the power.
■DO NOT unplug any internal connectors.
■Turn the MFC power switch off, before installing (or removing) the 
NC-9100h board.
1Disconnect the telephone line cord and handset curled cord 
from the MFC, turn the MFC power switch off, unplug the MFC 
power cord from the AC outlet, and then disconnect the 
interface cable.
2Remove the side cover....

OPTIONAL ACCESSORIES   13 - 7
3Loosen the two screws, and then remove the metal cover plate.
4Plug the NC-9100h into connector P1 located on the main board 
as shown in the illustration (press firmly) and secure the 
NC-9100h with the two screws.
5Put the metal shield plate back on and secure it with the two 
screws.
6Put the side cover back on.
7Reconnect any additional interface cables that you removed.
8Reconnect the power cable and then turn on the MFC power 
switch. 
9Reconnect the telephone line...

13 - 8   OPTIONAL ACCESSORIES
Step 2: Connecting the NC-9100h to an 
Unshielded Twisted Pair 10BASE-T or 
100BASE-TX Ethernet Network
To connect the NC-9100h to a 10BASE-T or 100BASE-TX Network, 
you must have an Unshielded Twist Pair Cable. One side of the cable 
must be connected to a free port on your Ethernet hub and the other 
side must be connected to the 10BASE-T or 100BASE-TX connector 
(an RJ45 Connector) of the NC-9100h.
Verifying successful hardware Installation:
Plug in the AC power cord....

OPTIONAL ACCESSORIES   13 - 9
LED
No light:
If both of the two LEDs are off, then the print server is not connected 
to the network.
Link/Speed LED is orange: Fast Ethernet
This Link/Speed LED will be orange if the print server is connected 
to a 100BASETX Fast Ethernet network.
Link/Speed LED is green: 10 BASE T Ethernet
This Link/Speed LED will be green if the print server is connected to 
a 10 BASE T Ethernet.
Active LED is yellow:
The Active LED will blink if the print server is connected to the...

13 - 10   OPTIONAL ACCESSORIES
Paper Tray #2
You can purchase the Paper Tray #2 accessory (LT-5000) to use as 
a third paper source. Tray #2 holds up to 250 sheets of 80 gsm 
paper.
Paper Tray #2 Holds approx. 250 sheets of 80 gsm
Basis Weight 60 to 105 gsm
Moisture Content 4% to 6% by weight
We Recommend:
Cut sheet:Xerox Premier 80 gsm
Xerox Business 80 gsm
Mode DATACOPY 80 gsm
IGEPA X-Press 80 gsm
 

GLOSSARY   G - 1
G
ADF (Automatic Document Feeder)  The original document can 
be placed in the ADF and scanned one page at a time 
automatically.
Automatic Redial  A feature that enables your MFC to redial the last 
fax number if the fax did not go through because the line was 
busy.
Auto Reduction  Reduces the size of incoming faxes.
Automatic fax transmission  Sending a fax without picking up the 
handset of the MFC (or pressing 
Hook/Hold/Recall).
Batch Transmission  As a cost savings feature, all...

G - 2   GLOSSARY
Compatibility Group  The ability of one fax unit to communicate 
with another. Compatibility is assured between ITU-T Groups.
Contrast  Setting to compensate for dark or light original 
documents, by making faxes or copies of dark original documents 
lighter and light original documents darker.
Cover Page  Prints a page at the other party’s fax machine that 
contains the sender and recipient’s name and fax number, 
number of pages and comment. You can generate an electronic 
cover page...

GLOSSARY   G - 3
FaxAbility  A subscriber service purchased from the telephone 
company that provides another phone number on an existing 
phone line. The Brother fax machine uses the new number to 
simulate a dedicated fax line.
Fax Detect  Enables your MFC to respond to CNG tones if you 
interrupt a fax call by answering it.
Fax Forwarding  Sends a fax received into the memory to another 
pre-programmed fax number.
Fax Storage  You can print stored faxes later at your MFC, or 
retrieve them from...

G - 4   GLOSSARY
Menu mode  Programming mode for changing your MFC’s settings.
MFL-Pro Suite  Turns your MFC into a printer and a scanner and 
enables PC faxing using the MFC.
OCR (optical character recognition)  The bundled ScanSoft
® 
TextBridge® software application converts an image of text to text 
you can edit.
One-Touch  Keys on the MFC control panel where you can store 
numbers for easy dialing. You can store a second number on 
each key if you press 
Shift and the One-Touch key together.
Out of...