Brother Laserprinter Hl 1435 User Guide

2 - 7   DRIVER AND SOFTWARE
Accessories tab 
When you install some options, you can add it and select its settings in the Accessories tab as follows.
1You can manually add and remove the options for any optional unit device that is installed on the 
printer. Tray settings will match the installed options.
2Paper Source Setting
This feature recognizes the paper size in each paper tray.
1
2 

DRIVER AND SOFTWARE   2 - 8
Support tab 
■You can download the latest driver by accessing the Brother Solutions Center at 
http://solutions.brother.com
■You can see the printer driver version.
■You can check the current driver settings. 

2 - 9   DRIVER AND SOFTWARE
For Macintosh® 
This printer supports Mac® OS 8.6 to 9.2 and Mac® OS X 10.1 to 10.2.
You can download the latest driver by accessing the Brother Solutions Center at 
http://solutions.brother.com
Page setup
You can set the Paper size, Orientation and Scale.
Layout
Set the Layout, Pages per Sheet and other settings.
The screens in this section are from Mac® OS X 10.1
The screens on your Macintosh
® will vary depending on your Operating System. 

DRIVER AND SOFTWARE   2 - 10
Specific settings
Set the Media Type, Resolution, Toner Save, and other settings. 

CONTROL PANEL   3 - 1
3
This section refers to the Light Emitting Diodes (LEDs) and Control panel button on the control panel. 
Figure 3-1
The LED indications shown in the table below are used in the illustrations in this chapter.
Control panel
LED is off
 or   or LED is on
 or 
 or LED is blinking
When the power switch is off or the printer is in Sleep mode, all the LEDs are off.
Drum
Ready
Alarm
Paper
Toner
Data 

3 - 2   CONTROL PANEL
LEDPrinter status
Figure 3-2
Sleep mode
The power switch is off or the printer is in Sleep mode. Pressing the Control 
panel button wakes up the printer from Sleep mode to Ready mode.
Figure 3-3
Ready to print
The printer is ready to print. Pressing Control panel button wakes up the printer 
to Ready mode. 
Figure 3-4
Warming up (Blinking at 1 second intervals)
The printer is warming up.
Cooling down or stop printing (Blinking at 2 second intervals)
The printer is cooling down and...

CONTROL PANEL   3 - 3
Figure 3-6
Data remaining in memory
Print data remains in the printer memory. If the Data LED is on for a long time 
and nothing has printed, press the Control panel button to print the remaining 
data.
Figure 3-7
Toner low
Indicates that the toner cartridge is nearly empty. Purchase a new toner 
cartridge and have it ready for when Toner Empty is indicated.
Figure 3-8
Toner empty
Replace the toner cartridge with a new one. See Replacing the toner cartridge 
on page 5-3. 
Figure...

3 - 4   CONTROL PANEL
Figure 3-10
Paper jam 
Clear the paper jam. See Paper jams and how to clear them on page 6-5. If the 
printer does not start printing, press the Control panel button. 
No paper 
Put paper in the printer. See Printing on plain paper on page 1-8. Then press 
the Control panel button.
Misfeed
Put the paper back in properly, and then press the Control panel button. The 
printer will start printing again. LED
Printer status
Ready
AlarmPaper
Toner
Data
Drum 

CONTROL PANEL   3 - 5
Service call indications
If there is an error that cannot be corrected, the printer will show that a service call is needed by lighting 
up all the LEDs and then alternating the following combination as shown in Table 1: LED indications 
when the service error occurs on page 3-6.
If you see the service call indication above, turn off the power switch, wait a few seconds, and then turn 
it back on and try to print again. 
If you cannot clear the error and see the same service call...

3 - 6   CONTROL PANEL
Table 1: LED indications when the service error occurs
Make a note of the indication and report the error status to your dealer or a Brother authorized service 
center by referring to the above table.
LEDs Fuser 
MalfunctionLaser BD 
MalfunctionScanner 
MalfunctionROM Error D-RAM Error Service A
Drum
Ready
Alarm
Data
LEDs Service B Engine 
Interface ErrorNV-RAM 
ErrorMain Motor 
MalfunctionCPU Runtime 
Error
Drum
Ready
Alarm
Data
Make sure that the front cover is fully closed before...