Brother Laserprinter Hl 1435 User Guide

1 - 8   ABOUT THIS PRINTER
Printing methods
Printing on plain paper 
You can print on plain paper from the paper tray or manual feed slot. For the paper you want to use, 
please see What kind of paper can I use? in this chapter.
Printing on plain paper from the paper tray
1Select the Paper Size, Media Type, Paper Source, and other settings in the printer driver.
Media Type: Plain Paper
Paper Source: Tray1
2Pull the paper tray completely out of the printer.
Figure 1-5 

ABOUT THIS PRINTER   1 - 9
3While pressing the blue paper-guide release lever, slide the paper guides to fit the paper size. 
Check that the guides are firmly in the slots.
Figure 1-6
4Put paper in the tray. Check that the paper is flat in the tray at all four corners.
Figure 1-7 

1 - 10   ABOUT THIS PRINTER
5Put the paper tray firmly back in the printer. Check that it is inserted fully into the printer.
6Send the print data to the printer.
Do not put more than 250 sheets of paper (80 g/m2) in the tray, or paper jams may occur. Check 
that paper is below the maximum paper mark (▼).
Figure 1-8
For two-sided printing, put the side that is going to be printed on (blank side) face down, with the 
top of the paper at the front of the tray.
Pull up the support flap to prevent paper from...

ABOUT THIS PRINTER   1 - 11
Printing on plain paper from the manual feed slot 
1Select the Paper Size, Media Type, Paper Source, and other settings in the printer driver.
Media Type: Plain Paper
Paper Source: Manual
2Send the print data to the printer.
The printer automatically turns on the Manual Feed mode when you put paper into manual feed slot.
A NO PAPER message is shown in the Status Monitor and indicated by the control panel LEDs until 
you put a sheet of paper in the manual feed slot.
Figure...

1 - 12   ABOUT THIS PRINTER
3Using both hands, slide the manual feed slot paper guides to the paper width to be used.
Figure 1-11
4Using both hands, insert into the paper into the manual feed slot until the front edge of the paper 
touches the paper feed roller.  Hold the paper in this position until the printer automatically feeds the 
paper in for a short distance, and then let go of the paper.
Figure 1-13
Pull up the support flap to prevent paper from sliding off the top output tray.
Figure 1-12
If...

ABOUT THIS PRINTER   1 - 13
5After the printed page comes out of the printer, put in the next sheet of paper as in Step 4 above. 
Repeat for each page that you want to print.
■Put the paper into the manual feed slot with the side to be printed face up.
■Make sure that the paper is straight and in the proper position on the manual feed slot. If it is not, 
the paper may not be fed properly, resulting in a skewed printout or a paper jam.
■Do not put more than one piece of paper in the manual feed slot at...

1 - 14   ABOUT THIS PRINTER
Printing on thicker paper and card stock 
When the rear cover is lifted up, the printer has a straight paper path from the manual feed slot  to the 
back of the printer. Use this paper feed and output method when you want to print on thicker paper or 
card stock.
When you select the paper you want to use, please see What kind of paper can I use? in this chapter.
1Select the Paper Size, Media Type, Paper Source, and other settings in the printer driver.
Media Type: Thick paper...

ABOUT THIS PRINTER   1 - 15
3Send the print data to the printer.
4Using both hands, set the width of the manual feed paper guides to the paper width you want to use. 
Figure 1-16
5Using both hands, insert the paper into the manual feed slot until the front edge of the paper touches 
the paper feed roller. Hold the paper in this position until the printer automatically feeds the paper 
in for a short distance, and then let go of the paper.
Figure 1-17
A NO PAPER status is shown by the control panel LEDs...

1 - 16   ABOUT THIS PRINTER
6After the printed page comes out of the printer, put in the next sheet of paper as in Step 5 above. 
Repeat for each page that you want to print.
7Close the rear cover.
Caution
Remove each sheet immediately after printing. Stacking the sheets may cause a paper jam or the 
paper to curl.
Figure 1-18
■Put the paper into the manual feed slot with the side to be printed face up.
■Make sure that the paper is straight and in the proper position in the manual feed slot. If it is...

ABOUT THIS PRINTER   1 - 17
Printing on envelopes 
Types of envelopes to avoid
Do not use envelopes:
■that are damaged, curled, wrinkled, or an usual shape 
■that are extremely shiny or textured 
■with clasps, snaps or tie strings
■with self-adhesive closures
■that are of a baggy construction
■that are not sharply creased
■that are embossed (have raised writing on them)
■that were previously printed by a laser printer
■that are pre-printed on the inside
■that cannot be arranged when put in a pile
■that...