Brother Laserprinter Hl 1435 User Guide

1 - 18   ABOUT THIS PRINTER
Printing on envelopes from the manual feed slot 
When the rear cover is lifted up, the printer has a straight paper path from the manual feed slot to the 
back of the printer. Use this paper feed and output method when you want to print envelopes.
1Select the Paper Size, Media Type, Paper Source, and other settings in the printer driver.
Media Type: Thicker paper
Paper Source: Manual
2Open the rear cover.
Figure 1-20
The printer automatically turns on the Manual Feed mode when...

ABOUT THIS PRINTER   1 - 19
3Send the print data to the printer.
4Using both hads, set the width of the manual feed paper guides to the envelope width. 
Figure 1-22
5Using both hands put the envelope in the manual feed slot until the front edge of the envelope 
touches the paper feed roller. Hold the envelope in this position until the printer automatically feeds 
it in for a short distance, and then let go of the envelope.
Figure 1-23
A NO PAPER status is shown by the control panel LEDs until you put a...

1 - 20   ABOUT THIS PRINTER
6After the printed envelope comes out of the printer, the printer will wait until you put in the next 
envelope. Repeat Step 5 for each envelope you want to print.
7After you finish the print job, close the rear cover.
■Make sure the envelope is straight as you insert it sideways in the manual feed slot. If it is not, 
the envelope may not be fed properly, resulting in a skewed printout or a jam.
■Do not put more than one envelope in the manual feed slot at any one time, or it...

ABOUT THIS PRINTER   1 - 21
Printing on transparencies
You can print on transparencies from the paper tray, manual feed slot.
Printing on transparencies from the paper tray
1Select the Paper Size, Media Type, Paper Source, and other settings in the printer driver.
Media Type: Transparencies
Paper Source: Tray1
2Pull the paper tray completely out of the printer.
Figure 1-24
■Do not put more than 10 transparencies in the paper tray. 

1 - 22   ABOUT THIS PRINTER
3While pressing the blue paper-guide release levers, slide the paper guides to fit the transparency 
size. Check that the guides are firmly in the slots.
Figure 1-25
4Put transparencies in the tray. Check that the transparencies are flat and below the maximum paper 
mark (▼). Do not put more than 10 transparencies in the tray at any one time, or it may cause a jam.
Figure 1-26 

ABOUT THIS PRINTER   1 - 23
5Put the paper tray firmly back in the printer.
6Send the print data to the printer.
Caution
Remove each transparency immediately.
Pull out the support flap to prevent transparencies from sliding off the top output tray.
Figure 1-27 

1 - 24   ABOUT THIS PRINTER
Printing on transparencies from the manual feed slot
When the rear cover is lifted up, the printer has a straight paper path from the manual feed slot to the 
back of the printer. 
1Select the Paper Size, Media Type, Paper Source, and other settings in the printer driver.
Media Type: Transparencies
Paper Source: Manual
Figure 1-28
2Open the rear cover.
Figure 1-29 

ABOUT THIS PRINTER   1 - 25
3Send the print data to the printer
4Using both hands, slide the manual feed paper guides to the transparency width.
Figure 1-31
5Using both hands put the transparency in the manual feed slot until its front edge touches the paper 
feed roller. Hold the transparency in this position until the printer automatically feeds it in for a short 
distance, and then let go of the transparency.
Figure 1-32
A NO PAPER status is shown by the control panel LEDs until you put a transparency...

1 - 26   ABOUT THIS PRINTER
6After the printed transparency comes out of the printer, put in the next transparency as described 
in Step 5 above. Repeat for each transparency that you want to print
7After you finish the print job, close the rear cover.
Caution
Remove each transparency immediately after printing. Stacking the printed transparencies may cause 
a paper jam or the transparency to curl.
■Put the transparency into the manual feed slot with the side to be printed face up.
■Make sure that the...

ABOUT THIS PRINTER   1 - 27
Printing on both sides of the paper (Manual duplex printing)
The supplied printer drivers for Windows® 95/98/Me, Windows NT® 4.0, Windows® 2000/XP, Mac® OS 
8.6 to 9.2 and Mac® OS X 10.1 enable manual duplex printing. For more information about how to 
choose the settings, see the Help text in the printer driver.
Manual duplex printing from the paper tray
1Choose the Duplex printing mode from the Advanced tab in the printer driver.
Figure 1-33
2Select the Paper Size, Media...