Brother Laserprinter Color Hl 3450cn User Guide

							CHAPTER 6 OPTIONS 
6-5 
12.Install the Paper Cassette into the Lower Tray Unit. 
13.Install the Paper Cassette into the printer. 
 
  
						

							CHAPTER 6 OPTIONS 
6-6 
H H
HO O
O
W W
W
T T
T
O O
OC C
CL L
L
E E
E
A A
A
R R
RP P
PA A
A
P P
P
E E
E
R R
RJ J
JA A
A
M M
M
S S
S
I I
I
N N
N
T T
T
H H
H
E E
EL L
LO O
O
W W
W
E E
E
R R
RT T
TR R
R
A A
A
Y Y
YU U
UN N
N
I I
I
T T
T
Paper Jam in the Cassette
1. When a Paper Jam has occurred in the Paper Cassette, remove the 
Paper Cassette from the printer. Pull the Cassette out half way, slightly 
lift it, and then pull the cassette from the printer. 
2. Remove the jammed paper and reinstall the cassette into the printer. 
Paper Jam at the Rear of the Lower Tray Unit
1. When a Paper Jam has occurred at the rear of the Lower Tray Unit, 
open the Rear Cover of the Lower Tray Unit. 
2. Remove the jammed paper, and then close the Rear Cover of the 
Lower Tray Unit.  
						

							CHAPTER 6 OPTIONS 
6-7 
   
D D
U U
P P
L L
E E
X X
   
U U
N N
I I
T T
   
( (
D D
X X
- -
3 3
4 4
0 0
0 0
) )
   
The following paper sizes can be used for the Duplex Unit. 
330 x 483 mm (13 x 19), A3, A4, B4, B5 
Executive, Ledger, Legal, Letter 
Note 
 The Lower Tray Unit must be connected before you install the Duplex 
Unit. 
 When you perform maintenance on the printer, open the Duplex Top 
Cover Assembly first. 
 When you want to open the Rear Access Cover of the printer, open the 
Duplex Lower Cover and the inside unit. 
 
1. Turn the printer off, and then unplug the power cord from the AC outlet. 
2. Remove the Fuser Cover that is 
located at the rear top of the 
printer. Remove the Rear Caps (2 
pieces) from the fuser unit. We 
recommend you remove those 
caps with a coin or a screwdriver. 
 
Fig. 6-10 
3. Remove the left hand side cover 
of the Lower Tray Unit. 
 
Fig. 6-11  
						

							CHAPTER 6 OPTIONS 
6-8 
 
4. Remove the Back caps (2 pieces) 
of the Lower Tray Unit. Push 
down lightly on the caps and slide 
them to the rear of the printer to 
remove them. 
 
Fig. 6-12 
5. Use the handholds of the Duplex 
Unit to lift the Duplex Unit up. 
 
Fig. 6-13 
 
 
Note 
Ensure that the Duplex Cover Top Assembly is aligned and latched 
straight with the lower part of the duplex unit. 
 
6. Insert the fixing pins at the sides 
of the Duplex Unit into the 
installation grooves in the Lower 
Tray Unit. 
 
Fig. 6-14 
 
 
Note 
Make sure that the Rear Cover of the Lower Tray Unit is closed.  
						

							CHAPTER 6 OPTIONS 
6-9 
 
7. Secure the pawls of the Duplex 
Unit into the rectangular holes in 
the back of the printer. 
 
Fig. 6-15 
8. Open the Duplex Cover Top Assembly. 
9. Securely connect the Duplex Unit 
and the Printer with the thumb 
screws (2 pieces). 
 
Fig. 6-16 
10. Close the Duplex Cover Top Assembly.  
						

							CHAPTER 6 OPTIONS 
6-10 
 
 
11. Connect the connector cable to 
the upper connector on the 
printer. 
 
Fig. 6-17 
12. Fit the left hand side cover of the Lower Tray Unit to the Lower Tray Unit. 
13. Plug the power cord into the AC outlet, and then turn the printer on.  
						

							CHAPTER 6 OPTIONS 
6-11 
   
C C
O O
M M
P P
A A
C C
T T
F F
L L
A A
S S
H H
   
C C
A A
R R
D D
   
/ /
   
H H
A A
R R
D D
   
D D
I I
S S
K K
   
D D
R R
I I
V V
E E
   
( (
H H
D D
- -
6 6
G G
/ /
H H
D D
- -
E E
X X
) )
   
C C
CO O
O
M M
M
P P
P
A A
A
C C
C
T T
TF F
FL L
L
A A
A
S S
S
H H
HC C
CA A
A
R R
R
D D
D
This printer has a slot for an optional CompactFlash card, which is a 
memory card. 
If you install an optional CompactFlash memory card, you can save macros, 
print log and fonts on it, and also select the re-print functions via the 
network. 
The following types of CompactFlash memory cards can be installed: 
 
Type I 
 16MB   SDCFB-16-505 
 32MB   SDCFB-32-505 
 48MB   SDCFB-48-505 
 64MB   SDCFB-64-505 
 80MB   SDCFB-80-505 
 96MB   SDCFB-96-505 
 128MB   SDCFB-128-505 
 160MB   SDCFB-160-505 
 196MB   SDCFB-196-505 
 
Type II 
 256MB   SDCFB-256-668 
 300MB   SDCFB-300-668 
 
Note 
 Do not install or remove cards with the power on, or you may lose all 
data from the card and may seriously damage the card. 
 For more information about these cards, consult the dealer where you 
purchased the printer.  
 For the latest information: http://solutions.brother.com  
						

							CHAPTER 6 OPTIONS 
6-12 
H H
HA A
A
R R
R
D D
DD D
DI I
I
S S
S
K K
KD D
DR R
R
I I
I
V V
V
E E
E( (
(
H H
H
D D
D
- -
-
6 6
6
G G
G
/ /
/
H H
H
D D
D
- -
-
E E
E
X X
X
) )
)
If you install an optional HDD, you can save macros, print log and fonts on 
it, and also select your print job and re-print it through the network. 
Confirm that the box contains the following items. 
 Hard disk 
 Hard disk cables (2) 
 Shoulder screws (4) 
 Screws (4) 
 Setup guide  
 
 
Note 
The supplied longer cable is for other printers, do not use it for this printer 
model. 
 
 
 
 
S S
SE E
E
L L
L
E E
E
C C
C
T T
T
I I
I
N N
N
G G
G
T T
T
H H
H
E E
EO O
OP P
P
T T
T
I I
I
O O
O
N N
N
A A
A
L L
LF F
FO O
O
N N
N
T T
T
S S
S
After you have installed the optional font card, you can select optional fonts 
using any of the following methods:   
1.  Through your application software 
 
2.  With a font selection command 
 
3.  With the Control Panel menu functions. 
  
When you select fonts through your application software, follow the 
instructions specific to your software. Refer to your software manual if you 
need assistance. When you select fonts with a font selection command, 
embed the font selection command in your program. See the Technical 
Reference Manual, which is optionally available for this printer.   
						

							CHAPTER 6 OPTIONS 
6-13 
 
Note 
When you select the fonts through your software or with a command, note 
the following: 
 You do not need to be concerned about the Font control panel setting. 
The software or command setting overrides the printer setting. 
 Be sure to install the font card that has your desired fonts. The printer 
automatically selects the font that has exactly the same or similar 
characteristics as those you set through the software or with a 
command. If the installed font card happens to have a font of similar 
characteristics, the printer will print in an unexpected font. 
 
To select fonts with the Control Panel setting menu, follow these basic 
steps:   
1. Press any of the Menu buttons (+, –, Set or Back) to take the printer 
Off Line. 
2. Press + or – until “INFORMATION” appears on the LCD display. 
3. Press Set to proceed to the next menu level, and then press + or – 
until “PRINT FONTS” appears. 
4. Press Set to print the list of optional fonts (Fig. 6-18). 
5. Find the Font Number on the list. 
  
						

							CHAPTER 6 OPTIONS 
6-14 
 
 
Fig. 6-18 
 
6. Use + or – on the Control Panel to select “PRINT MENU.” 
7. Press Set to proceed to the next menu level, and then press + or – to 
select:  “HP LASERJET,” “EPSON FX-850”, or “IBM PROPRINTER.” 
8. Press the Set key to select the Emulation for the fonts you want to 
select; “HP LASERJET,” “EPSON FX-850,” or “IBM PROPRINTER.” 
9. Use + or – key to select “FONT NO,” and then select the Font Number 
of the font you want. 
Font Number