Brother HL 7050N User Manual

3 - 27 CONTROL PANEL
HL7050_US_UG_FM5.5
PRINT MENU
Display ShowsDescription
MEDIA TYPE=PLAIN PAPER/TRANSPARENCIES/THICK PAPER/
THICKER PAPER/BOND PAPER/ENVELOPES/THIN 
PAPER
PAPERSet the paper size to LETTER, LEGAL, A4, EXECUTIVE, 
COM-10, DL, JIS B5, B5, A5, B6, A6, MONARCH, C5 and 
A4 LONG.
COPIESYou can check the total number of printed pages.
Shows the number of printed pages (1 to 999).
ORIENTATIONThis printer can print pages in portrait or landscape 
orientation.
PORTRAIT or LANDSCAPE
PRINT...

CONTROL PANEL 3 - 28
HL7050_US_UG_FM5.5
HP LASERJET
(continued)Subsetting Description
AUTO CR=OFF/ON
ON: LF LF+CR, FF+CR, or 
VT→VT+CR
OFF: LF→LF, FF→FF, or VT→VT
AUTO WRAP=OFF/ON
Select whether a line feed and 
carriage return will happen when the 
printer reaches the right margin.
AUTO SKIP=ON/OFF
Select whether a line feed and 
carriage return will happen when the 
printer position reaches the bottom 
margin.
LEFT MARGIN=##
Set the left margin at column 0 to 70 
columns at 10 cpi.
RIGHT MARGIN=##
Set...

3 - 29 CONTROL PANEL
HL7050_US_UG_FM5.5
EPSON FX-850
(continued)Subsetting Description
AUTO LF=OFF/ON
ON: CR→CR+LF
OFF: CR→CR
AUTO MASK=OFF/ON 
LEFT MARGINSet the left margin at column 0 to 70 
columns at 10 cpi.
RIGHT MARGINSet the right margin at column 10 to 
80 columns at 10 cpi.
TOP MARGINSet the top margin at a distance from 
the top edge of the paper - 0, 0.33, 
0.5, 1.0, 1.5 or 2.0. The factory 
setting is 0.33.
BOTTOM MARGINSet the bottom margin at a distance 
from the bottom edge of the paper -...

CONTROL PANEL 3 - 30
HL7050_US_UG_FM5.5
IBM PROPRINTER
(continued)Subsetting Description
TOP MARGINSet the top margin at a distance from 
the top edge of the paper - 0, 0.33, 
0.5, 1.0, 1.5 or 2.0. The factory 
setting is 0.33.
BOTTOM MARGINSet the bottom margin at a distance 
from the bottom edge of the paper - 
0, 0.33, 0.5, 1.0, 1.5 or 2.0. The 
factory setting is 0.33.  
LINESSet the number of lines on each page 
from 5 to 128 lines.
HP-GL CHAR SET(STD)=####
CHAR SET(ALT)=####
PEN # SIZEPEN1 to 6...

3 - 31 CONTROL PANEL
HL7050_US_UG_FM5.5   
NETWORK (only on a Network)
Display ShowsDescription
TCP/IPSubsetting Description
TCP/IP ENABLE=ON/OFF
IP ADDRESS=###.###.###.###
SUBNET MASK=###.###.###.###
GATEWAY=###.###.###.###
IP BOOT TRIES=#
IP METHOD
=AUTO/STATIC/RARP/BOOTP/DHCP
NETWARE NETWARE ENABLE=ON/OFF
NET FRAME=AUTO/8023/ENET/8022/SNAP
APPLETALK=ON/OFF
NETBEUI=ON/OFF
DLC/LLC=ON/OFF
BANYAN=ON/OFF
LAT=ON/OFF
NETBIOS/IP=ON/OFF
APIPA=ON/OFF
ENET
=AUTO/100B-FD/100B-HD/10B-FD/10B-HD
 

CONTROL PANEL 3 - 32
HL7050_US_UG_FM5.5
INTERFACE
Display ShowsDescription
SELECT=AUTO/PARALLEL/RS-232C/USB/NETWORK
AUTO IF TIME= 1:99 (sec)
You need to set the time-out period for the auto interface 
selection. 
INPUT BUFFER= Level1:15
Increase or 
decrease the input 
buffer capacity.RESTART PRINTER?
PARALLELWhen using the parallel interface
Sub-setting Menu Description
HIGH SPEED=ON/OFF
Turns high-speed parallel 
communications on or off.  
BI-DIR=ON/OFF
Turns bi-directional parallel 
communications on...

3 - 33 CONTROL PANEL
HL7050_US_UG_FM5.5
*1Appears when FAX MODE is off.
*2Appears when FAX MODE is on.
RS-232C
(continued)Sub-setting Menu Description
DTR(ER)
*1=ON/OFF
ROBUST XON 
*1=OFF/ON
RING DELAY 
*2=0/1/2/3/4
REDUCTION 
*2=AUTO/OFF/90%
RAM SIZE 
*2=1:##MBYTE
RECEIVE 
*2=ON/OFF
INTERVAL 
*2=OFF/6H/12H/24H/2D/4D/7D
RESET MENU
Display ShowsDescription
RESET PRINTERResets the printer and restores all printer settings (including 
command settings) to settings you have previously made 
with the control...

CONTROL PANEL 3 - 34
HL7050_US_UG_FM5.5
Set date and time
Press the + or - button until the SETUP mode 
appears (and to display each setting shown below).
Press the Set button, and then press the 
+or - button until DATE & TIME appears.
Press the Set button, and then press the 
+or - button until YEAR appears.
Press the Set button.
Press the + button.
Press the Set button.
Press the Set button.
Press the Set button.
--MENU--
INFORMATION
--MENU--
SETUP
SETUP 
DATE & TIME
DATE & TIME
YEAR
YEAR
=1999...

3 - 35 CONTROL PANEL
HL7050_US_UG_FM5.5
Set IP Address
Press the + or - button until the NETWORK mode 
appears (and to display each setting shown below).
Press the Set button.
Press the Set button.
Press the + button.
Press the Set button.
The last digit in the first part of the number 
is blinking.
Press the + or - button to increase or 
decrease the number.
Press the Set button to go to the next 
number. 
Repeat this process until you have set your 
IP address.
Press the Set button to complete the IP...

CONTROL PANEL 3 - 36
HL7050_US_UG_FM5.5
About emulation modes
This printer has the following emulation modes.  
HP LaserJet Mode
The HP LaserJet mode (or HP mode) is the emulation mode in which 
this printer supports the PCL6 language of the Hewlett-Packard 
LaserJet laser printer.  Many software applications support this type 
of laser printer.  Using this mode will allow your printer to operate at 
its best with those applications. 
BR-Script 3 Mode
BR-Script is an original Brother page description...