Brother HL 6050D User Manual

3 - 20   CONTROL PANEL
NETWORK (only on a Network)
Display ShowsDescription
TCP/IPSubsetting Description
TCP/IP ENABLE=ON/OFF
IP ADDRESS=###.###.###.###
SUBNET MASK=###.###.###.###
GATEWAY=###.###.###.###
IP BOOT TRIES=#
IP METHOD=AUTO, STATIC, RARP, BOOTP, DHCP
APIPA=ON/OFF
NETWARE NETWARE ENABLE=ON/OFF
NET FRAME=AUTO, 8023, ENET, 8022, SNAP
APPLETALK=ON/OFF
NETBEUI=ON/OFF
DLC/LLC=ON/OFF
NETBIOS/IP=ON/OFF
ENET=AUTO, 100B-FD, 100B-HD, 10B-FD, 10B-HD
 

CONTROL PANEL   3 - 21
INTERFACE
Display ShowsDescription
SELECT=AUTO/PARALLEL/USB/NETWORK
AUTO IF TIME= 1, 2, 3 ... 99 (sec)
You need to set the time-out period for the auto interface selection. 
INPUT BUFFER= Level1, 2, 3 ... 15
Increases or decreases the 
input buffer capacity.RESTART PRINTER?
PARALLELWhen using the parallel interface
Sub-setting Menu Description
HIGH SPEED=ON/OFF
Turns high-speed parallel communications ON or 
OFF. 
BI-DIR=ON/OFF
Turns bi-directional parallel communications ON 
or...

3 - 22   CONTROL PANEL
Set IP Address
Press the + or - button until NETWORK appears (and to display each setting 
shown below).
Press the Set button.
Press the Set button.
Press the + button.
Press the Set button.
The last digit in the first part of the number is blinking.
Press the + or - button to increase or decrease the number.
Press the Set button to go to the next number. 
Repeat this process until you have set your IP address.
Press the Set button to complete the IP address.
An asterisk appears at...

CONTROL PANEL   3 - 23
About emulation modes
This printer has the following emulation modes. 
HP LaserJet Mode
The HP LaserJet mode (or HP mode) is the emulation mode in which this printer supports the PCL6 
language of the Hewlett-Packard LaserJet laser printer. Many software applications support this type of 
laser printer. Using this mode will allow your printer to operate at its best with those applications. 
BR-Script 3 Mode
BR-Script is an original Brother page description language and a...

3 - 24   CONTROL PANEL
List of factory settings
Table 3-1 shows the factory settings. 
Network factory default setting
If you wish to reset the print server back to its default factory settings (resetting all information such as 
the password and IP address information), hold down the network test button on the network board 
(NC-6100h) for more than 5 seconds.
■The emulation mode affects the setting. Effective modes are shown in brackets in the following 
table.
■The following settings cannot be...

CONTROL PANEL   3 - 25
Table 3 - 1: List of factory settings 
Display ShowsSubmenuFactory setting
PAPER SOURCE=AUTO
PRIORITY=MP>T1>T2
MP FIRST=OFF
MP SIZE=ANY
MANUAL FEED=OFF
TRAY1 SIZE=DETECT SENSOR
TRAY2 SIZE=DETECT SENSOR
DUPLEX=OFF
QUALITY RESOLUTION=600
HRC=MEDIUM
TONER SAVE=OFF
DENSITY0
SETUP LANGUAGE=ENGLISH
PANEL CONTROLSubsetting Factory setting
LCD DENSITY =0
AUTO ONLINE =ON
BUTTON REPEAT =0.1 SEC
MESSAGE SCROLL LEVEL 1
ERROR BUZZER=OFF
PANEL BUZZER=OFF
BUZZER VOLUME=LOW
POWER SAVE TIME=30 MIN...

3 - 26   CONTROL PANEL
PRINT MENU 
(continued)HP LASERJETSubsetting Factory setting
FONT NO. =59
FONT PITCH =10.00/12.00
SYMBOLSET =PC8
AUTO LF =OFF
AUTO CR =OFF
AUTO WRAP =OFF
AUTO SKIP =ON
LEFT MARGIN =####
RIGHT MARGIN =####
TOP MARGIN =####
BOTTOM MARGIN =####
LINES =####
EPSON FX-850FONT NO. =59
FONT PITCH =10.00/12.00
SYMBOLSET =US ASCII
AUTO LF =OFF
AUTO MASK =OFF
LEFT MARGIN =####
RIGHT MARGIN=####
TOP MARGIN=####
BOTTOM MARGIN=####
LINES=####
IBM PROPRINTER FONT NO.=59
FONT PITCH=10.00/12.00...

CONTROL PANEL   3 - 27
*1 Automatic Private IP Addressing (APIPA) protocol automatically configures an IP address and subnet mask. 
For more details, see the Network Users Guide, which is provided on the CD-ROM. NETWORK TCP/IPSubsetting Factory setting
TCP/IP ENABLE=ON
IP ADDRESS=169.254.###.### *
1
SUBNET MASK =255.255.0.0 *1
GATEWAY=0.0.0.0
IP BOOT TRIES=3
IP METHOD=AUTO
APIPA=ON
NETWARENETWARE ENABLE=ON
NET FRAME=AUTO
APPLETALK=ON
NETBEUI=ON
DLC/LLC=ON
NETBIOS/IP=ON
ENET=AUTO
INTERFACE SELECT=AUTO...

3 - 28   CONTROL PANEL
For visually-impaired users
Buzzer indications
The control panel has a buzzer. The buzzer will sound when one of the control panel buttons is pressed, 
or the status of the printer changes. See the table for a description of the buzzer meanings.
You can change the settings of the buzzer by using the buttons on the control panel. 
To change the setting of the buzzer, press the + (plus) button until SETUP is displayed, then press the 
Set button. Press the + (plus) button until ERROR...

CONTROL PANEL   3 - 29
Braille symbols
The control panel buttons are marked with Braille characters for visually-impaired users as shown in the 
table.
*Braille indicates the first 2 or 3 letters of the English button name. For example, Job Cancel is shown 
as “can” in Braille.
The control panel with Braille symbols is optionally available for some countries. If you want to buy 
an optional control panel with Braille symbols, call the dealer you bought the printer from.
Table 3 - 3: Braille symbols list...