Brother Hl 5130 User Manual
Have a look at the manual Brother Hl 5130 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 331 Brother manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
CONTROL PANEL 3 - 5 Service call indications If there is an error that cannot be cleared by the user, the printer will show that a service call is needed by lighting up all the LEDs as shown in Figure 3-12. Figure 3-12 If you see the service call indication above, follow the steps below: 1Take out the DIMM (Dual Inline Memory Module) from your printer, if you have a DIMM installed. 2Turn off the power switch, wait a few seconds, and then turn it back on and try to print again. If you cannot clear the error and see the same service call indication after turning the printer back on, call your dealer or a Brother authorized service representative. When you press the Go and the Job Cancel buttons together, the LEDs will light up with one of the combinations shown in Table 1. See Table 1: LED indications while pressing Go and Job Cancel on page 3-6 to identify the error. For example, the LED indication below shows a fixing unit failure. Figure 3-13 Toner Drum Paper Status Toner Drum Paper Status
3 - 6 CONTROL PANEL Table 1: LED indications while pressing Go and Job Cancel Make a note of the indication and report the error status to your dealer or a Brother authorized service representative by referring to the above table. *1 If this error occurs, turn the power switch off, wait a few seconds, and then turn it on again. Leave the printer for 10 minutes with the power on. If the error occurs again, consult your dealer or Brother authorized service representative. LEDs Fixing unit failure*1Laser unit failureMain motor failureMain PCB failureEngine PCB failureDIMM failure Toner Drum Paper Status Make sure that the front cover is fully closed before you report a service call.
CONTROL PANEL 3 - 7 Control panel buttons The control panel buttons have the following functions: Cancel printing If you press the Job Cancel button while printing, the printer will immediately stop printing and will then eject the paper. Wake-up If the printer is in Sleep mode, press the Go or Job Cancel button to wake the printer up and go to the Ready state. Form feed If the yellow Status LED is on, press the Go button. The printer will print any data that is left in the printer memory. Error recovery If there is an error, the printer will recover automatically from some errors. If an error is not automatically cleared, press the Go button to clear the error, and then continue to use the printer. Reprint If you want to reprint a document that has just been printed, you can do this by pressing and holding down the Go button until all four LEDs are lit and then release the Go button.
3 - 8 CONTROL PANEL Print a test page You can use the Go button or the printer driver to print a test page. Using control panel button 1Turn off the printer. 2Make sure that the front cover is closed and the power cord is plugged in. 3Hold down the Go button as you turn on the power switch. All the LEDs light up and then go off again. Keep the Go button pressed down until the Toner LED comes on. When the Toner LED comes on, release the Go button. 4Press the Go button again. The printer will print a test page. Using the printer driver If you are using Brother’s Windows® PCL printer driver, click the Print Test Page button. It is in the General tab of the Windows® printer driver.
CONTROL PANEL 3 - 9 Printer Settings You can print the current settings using the control panel button or printer driver. Using the control panel button 1Make sure that the front cover is closed and the power cord is plugged in. 2Turn on the printer and wait until the printer is in the Ready state. 3Press the Go button three times. The printer will print the current printer settings. Using the printer driver If you are using Brother’s Windows® PCL printer driver, you can print the current printer settings by clicking the Print Settings button in the Support tab.
3 - 10 CONTROL PANEL Print fonts (Not available for HL-5130) You can print a list of the internal fonts using the control panel button or printer driver. Using the control panel button 1Turn off the printer. 2Make sure that the front cover is closed and the power cord is plugged in. 3Hold down the Go button as you turn on the power switch. All the LEDs light up and then go off again. Keep the Go button pressed down until the Toner LED comes on. When the Toner LED comes on, release the Go button. 4Press and hold the Go button again until the Drum LED comes on. 5When the Drum LED comes on, release the Go button. The printer will print a list of the internal fonts. Using the printer driver (Not available for HL-5130) If you are using Brother’s Windows® PCL printer driver, you can print a list of the internal fonts by clicking the Print Fonts button in the Support tab.
CONTROL PANEL 3 - 11 Network factory default setting (For HL-5170DN) If you wish to reset the print server back to its default factory settings (resetting all information such as the password and IP address information), please follow these steps: 1Turn off the printer. 2Make sure that the front cover is closed and the power cord is plugged in. 3Hold down the Go button as you turn on the power switch. All the LEDs will light up. Keep the button pressed down until the Toner LED comes on. When the Toner LED comes on, release the Go button. 4Hold down the Go button and keep it pressed down until the yellow Status LED comes on. When the Status LED comes on, release the Go button. 5When all the LEDs light up again, the printer will start warming up. The print server has been reset to its default factory settings. Disabling the APIPA protocol (For HL-5170DN) If you wish to automatically disable the APIPA protocol, please follow these steps: 1Turn off the printer. 2Make sure that the front cover is closed and the power cord is plugged in. 3Hold down the Go button as you turn on the power switch. All the LEDs will light up. Keep the button pressed down until the Toner LED comes on. When the Toner LED comes on, release the Go button. 4Hold down the Go button and keep it pressed down until the green Status LED comes on. When the Status LED comes on, release the Go button. ■For more information on APIPA, see the Network User’s Guide or visit http://solutions.brother.com ■You can also disable the APIPA protocol using EWS, BRAdmin Professional or Web BRAdmin.
4 - 1 OPTIONS 4 This printer has the following optional accessories. You can increase the capabilities of the printer with these items. Click the symbol L in the table to see the information for each item. DIMM We recommend that you expand the printer memory to avoid any memory full errors. For HL-5140 and HL-5150D This printer has 16 MB of standard memory and a slot for optional additional memory. The memory can be expanded up to a total of 144 MB by installing a commercially available DIMM (Dual In-line Memory Module). For HL-5170DN This printer has 32 MB of standard memory and a slot for optional additional memory. The memory can be expanded up to a total of 160 MB by installing a commercially available DIMM (Dual In-line Memory Module). The following DIMM size can be installed: In general, DIMM must have the following specifications: Options Model DIMM Lower tray unit Print server HL-5130N/A N/AL HL-5140LLL HL-5150DLLL HL-5170DNLLStandard ■16 MB ■32 MB ■64 MB ■128 MB TECHWORKS TECHWORKS TECHWORKS TECHWORKS12456-0001 12457-0001 12458-0001 12459-0001 For more information, visit Techworks web site at www.techworks.com Type CAS Latency Clock Frequency Capacity Height Parity DRAM Type100 pin and 32 bit output 2 or 3 66MHz or more 16, 32, 64 MB or 128 MB 35 mm (1.4 inches) or less NONE SDRAM 4 Bank
OPTIONS 4 - 2 Installing additional memory 1Turn off the printer power switch, and then unplug the printer. Disconnect the interface cable from the printer. Figure 4-1 Caution Make sure you turn the printer OFF before you install or remove the DIMM. 2Remove the side cover. Use a coin to loosen the two screws, and then remove the metal plate. 3Unpack the DIMM and hold it by the edges. Caution DIMM boards can be damaged by even a small amount of static electricity. Do not touch the memory chips or the board surface. Wear an antistatic wrist strap when you install or remove the board. If you do not have an antistatic wrist strap, frequently touch the bare metal on the printer. ■Additional memory is useful and may be necessary if you are using the Page Protection function. (For HL-5170DN) ■You have to expand the printer memory by adding a DIMM to use the FTP/IPP protocol. Figure 4-2 Figure 4-3
4 - 3 OPTIONS 4Hold the DIMM by the side edges. Line up the notches on the DIMM with the DIMM slot. (Check that the locks on each side of the DIMM slot are open or facing outwards.) Figure 4-4 5Press the DIMM straight into the slot (press firmly). Make sure the locks on each side of the DIMM click into place. (To remove a DIMM, you must release the locks.) 6Put the metal plate back on and secure the metal plate with the two screws. 7Put the side cover back on. 8Reconnect the interface cable (printer cable) to your computer. Plug the printer back in, and then turn on the printer power switch. To check that you have installed the DIMM correctly, print the printer settings by using the selection in the driver and check the printout to make sure it shows the additional memory. See Printer Settings and Print fonts in Chapter 3.