Brother HL 2700CN User Manual

5 - 16   ROUTINE MAINTENANCE
120K kit
When you see the following message on the LCD, you must replace the items in the 120K kit, which are 
the transfer belt cleaner, transfer roller, paper pick-up roller, separator pad and transfer belt.
Replacing the transfer belt cleaner
1) Turn off the printer power switch.
2) Open the top cover of the printer.
Figure 5-20
■We recommend that you call your service provider when you see the following message on the 
LCD panel:
■It is also recommended that your dealer...

ROUTINE MAINTENANCE   5 - 17
3) Remove the transfer belt cover.
Figure 5-21
4) Remove the transfer belt cleaner by grasping the handle and lift it up.
Figure 5-22
5) Clean the area where the new transfer belt cleaner is to be installed with a dry cotton cloth.
Figure 5-23
6) Put the new transfer belt cleaner into the printer by gently placing the brass bearings into the 
guides, and then pushing the handle down until the bearings click into place. Make sure the 
transfer belt cleaner is free to move...

5 - 18   ROUTINE MAINTENANCE
the housing after you have installed it.
Figure 5-24
7) Put the transfer belt cleaner cover back in, and then close the top cover.
8) Turn the printer power switch back on.
Replacing the transfer roller
1) Turn off the printer power switch.
2) Open the back cover of the printer.
Figure 5-25
3) Release the transfer roller lock levers on the right and left-hand sides, and then lift the levers to 
If you have the duplex unit installed, open the duplex back cover and the duplex...

ROUTINE MAINTENANCE   5 - 19
release the transfer roller.
Figure 5-26
4) Take out the transfer roller by gently pulling the right-hand side up and sliding the transfer roller 
to the right.
 

5 - 20   ROUTINE MAINTENANCE
Figure 5-27
5) Put in the new transfer roller by holding the lock levers of the transfer roller and adjusting the 
angle of the transfer roller lever shafts (both sides) to match the transfer unit grooves. Put the 
transfer roller onto the shafts and place the roller onto the springs as shown below:
Figure 5-28
6) Push the lock levers down to lock the transfer roller into place.
7) Close the back cover.
8) Turn the printer power switch back on.Figure 5-29Figure 5-30
Lock...

ROUTINE MAINTENANCE   5 - 21
Cleaning
Clean the outside and inside of the printer regularly with a dry soft cloth. When you replace the toner 
cartridge, make sure you clean the inside of the printer. If printed pages are stained with toner, clean the 
inside of the printer with a dry soft cloth.
We recommend cleaning the following parts of the printer every 20,000 printed pages or every 12 
months:
■Paper guides of the paper tray
■Registration roller
■Paper pick-up roller
■Transfer roller unit
■Transfer...

5 - 22   ROUTINE MAINTENANCE
Cleaning the outside of the printer
Clean the outside of the printer as follows: 
1Turn off the printer power switch and unplug the printer.
2Take the paper tray out of the printer.
3Wipe the outside of the printer with a soft cloth to remove dust. Dip the cloth in water and wring it 
out thoroughly for cleaning.
Figure 5-31
4Clean the paper guides of the paper tray with a dry soft cloth. Remove anything that is stuck inside 
the paper tray.
Figure 5-32
5Put the paper tray...

ROUTINE MAINTENANCE   5 - 23
Cleaning the inside of the printer
Clean the printer interior as follows:
1Turn off the printer power switch and unplug the printer.
2Open the back cover of the printer.
Figure 5-33
3Clean the registration roller and the paper pick-up roller with a dry soft cloth to prevent paper jams.
When you clean the inside of the printer, pay attention to the following:
■If your clothes are smeared with toner, wipe off the toner with a dry cloth. Immediately wash your 
clothes in cold...

5 - 24   ROUTINE MAINTENANCE
4Clean the transfer roller unit and the transfer roller guide with a dry soft cloth to prevent paper jams.
Figure 5-38
5Clean the exit roller. This will help to prevent paper jams at the paper exit and dirt from appearing 
on your printouts.
Figure 5-39
6Close the back cover.
■Be careful you do not break the actuator while cleaning the registration roller and paper pick-up 
roller.
■Make sure you do not put too much pressure on the registration roller and paper pick-up...

ROUTINE MAINTENANCE   5 - 25
7Open the top cover.
Figure 5-40
8To release the lock, push the green belt cartridge lock levers that are on both sides inwards.
Figure 5-41
9Remove the OPC belt cartridge from the printer.
Figure 5-42
10Place the OPC belt cartridge on a flat surface and cover the shiny green OPC belt with a piece of 
paper to prevent exposing it to light.
■Do not touch the OPC belt surface with your bare hands or gloves.
■If the belt is exposed for more than two minutes to a light source of...