Brother DCP 8065DN User Manual

							Safety and Legal39
To use the machine safelyA
Please keep these instructions for later reference and read them before attempting any 
maintenance.
WARNING
There are high voltage electrodes inside the 
machine. Before you clean the inside of the 
machine, make sure you have unplugged the 
power cord from the AC power outlet.
 
Do not handle the plug with wet hands. Doing this 
might cause an electrical shock.
 
After you have just used the machine, some 
internal parts of the machine will be extremely hot. 
When you open the front or back cover of the 
machine, DO NOT touch the shaded parts shown 
in the illustration.
 
The fuser unit is marked with a caution label. Please do 
not remove or damage the label.
 
To prevent injuries, be careful not to put your 
hands on the edge of the machine under the 
document cover.
 
 
						

							40
To prevent injuries, be careful not to put your 
fingers in the area shown in the illustrations.
 
DO NOT use a vacuum cleaner to clean up scattered toner. Doing this might cause the toner 
dust to ignite inside the vacuum cleaner, potentially starting a fire. Please carefully clean the 
toner dust with a dry, lint-free cloth and dispose of it according to local regulations.
When you move the machine, grasp the side hand 
holds that are under the scanner. DO NOT carry 
the machine by holding it at the bottom.
 
This product must be installed near an AC power outlet that is easily accessible. In case of 
an emergency, you must disconnect the power cord from the AC power outlet to shut off the 
power completely.
To reduce the risk of shock or fire, use only a No. 26 AWG or larger telecommunication line cord.
 
						

							Safety and Legal41
CAUTION 
Lightning and power surges can damage this product! We recommend that you use a quality 
surge protection device on the AC power line or unplug the cord during a lightning storm.
 
WARNING 
IMPORTANT SAFETY INSTRUCTIONS
When using your equipment, basic safety precautions should always be followed to reduce the 
risk of fire, electric shock and injury to people, including the following:
1 Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, washing machine, or in a wet basement or near a swimming pool.
2 Avoid using this product during an electrical storm. There may be a remote risk of electric  shock from lightning.
3 Do not use this product to report a gas leak in the vicinity of the leak.
4 Use only the power cord provided with the machine.
SAVE THESE INSTRUCTIONS
 
 
						

							42
Important InformationA
Federal Communications Commission (FCC) 
Declaration of Conformity (USA only)A
declares, that the products
Product Name: DCP-8060, DCP-8065DN
comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This 
device may not cause harmful interference, and (2) this device must accept any interference 
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment generates, uses, and can 
radiate radio frequency energy and, if not installed and used in accordance with the instructions, 
may cause harmful interference to radio communications. However, there is no guarantee that 
interference will not occur in a particular installation. If this equipment does cause harmful 
interference to radio or television reception, which can be determined by turning the equipment 
off and on, the user is encouraged to try to correct the interference by one or more of the following 
measures: „ Reorient or relocate the receiving antenna.
„ Increase the separation between the equipment and receiver.
„ Connect the equipment into an outlet on a circuit different from that to which the receiver is 
connected.
„ Call the dealer or an experienced radio/TV technician for help.
ImportantA
Changes or modifications not expressly approved by Brother Industries, Ltd. could void the user’s 
authority to operate the equipment.
Important — about the interface cableA
A shielded interface cable should be used to ensure compliance with the limits for a Class B digital 
device.Responsible Party:
Brother International Corporation
100 Somerset Corporate Boulevard
Bridgewater, NJ 08807–0911 USA
TEL: (908) 704–1700
 
						

							Safety and Legal43
Industry Canada Compliance Statement (Canada only) A
This Class B digital apparatus complies with Canadian ICES–003. 
Cet appareil numérique de la classe B est conforme à la norme NMB–003 du Canada.
Disconnect deviceA
This product must be installed near an electrical jack that is easily accessible. In case of 
emergencies, you must disconnect the power cord from the electrical jack to shut off power 
completely.
LAN connection A
CAUTION 
Do not connect this product to a LAN connection that is subject to over-voltages.
 
International ENERGY STAR® Compliance StatementA
The purpose of the International ENERGY STAR® Program is to promote the development and 
popularization of energy-efficient office equipment.
As an ENERGY STAR
® Partner, Brother Industries, Ltd. has determined that this product meets 
the ENERGY STAR
® guidelines for energy efficiency.
 
 
						

							44
Laser safetyA
This equipment is certified as a Class 1 laser product under the U.S. Department of Health and 
Human Services (DHHS) Radiation Performance Standard according to the Radiation Control for 
Health and Safety Act of 1968. This means that the equipment does not produce hazardous laser 
radiation.
Since radiation emitted inside the equipment is completely confined within protective housings 
and external covers, the laser beam cannot escape from the machine during any phase of user 
operation.
FDA regulationsA
U.S. Food and Drug Administration (FDA) has implemented regulations for laser products 
manufactured on and after August 2, 1976. Compliance is mandatory for products marketed in the 
United States. The following label on the back of the machine indicates compliance with the FDA 
regulations and must be attached to laser products marketed in the United States.
WARNING 
Use of controls, adjustments or performance of procedures other than those specified in this 
manual may result in hazardous invisible radiation exposure.
Internal laser radiation 
Max. Radiation Power  5 mW
Wave Length 770 – 810 nm
Laser Class Class 3B
 
Manufactured:
BROTHER CORP. (ASIA) LTD.
BROTHER BUJI NAN LING FACTORY 
Gold Garden Industry, Nan Ling Village, Buji, Rong Gang, Shenzhen, China. 
This product complies with FDA performance standards for laser products except for deviations 
pursuant to Laser Notice No. 50, dated July 26, 2001.
 
						

							Safety and Legal45
Important safety instructionsA
1 Read all of these instructions.
2 Save them for later reference.
3 Follow all warnings and instructions marked on the product.
4 Unplug this product from the wall outlet before cleaning inside of the machine. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
5 Do not place this product on an unstable cart, stand, or table. The product may fall, causing  serious damage to the product.
6 Slots and openings in the cabinet at the back or bottom are provided for ventilation. To ensure  reliable operation of the product and to protect it from overheating, these openings must not 
be blocked or covered. The openings should never be blocked by placing the product on a bed, 
sofa, rug, or other similar surface. This product should never be placed near or over a radiator 
or heater. This product should never be placed in a built-in installation unless proper ventilation 
is provided.
7 This product should be connected to an AC power source within the range indicated on the  rating label. Do NOT connect it to a DC power source. If you are not sure, contact a qualified 
electrician.
8 This product is equipped with a 3-wire grounded plug. This plug will only fit into a grounded  power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, call 
your electrician to replace your obsolete outlet. Do not defeat the purpose of the grounded 
plug.
9 Use only the power cord supplied with this machine.
10 Do not allow anything to rest on the power cord. Do not place this product where people can  walk on the cord.
11 If an extension cord is used with this product, make sure that the total ampere ratings on the  products plugged into the extension cord do not exceed the extension cord ampere rating. 
Also, make sure that the total of all products plugged into the AC power outlet does not exceed 
15 amperes (US only).
12 Do not place anything in front of t he machine that will block printed pages.
13 Wait until pages have exited the machine before picking them up.
14 Never push objects of any kind into this product through cabinet slots, since they may touch  dangerous voltage points or short out parts resulting in the risk of fire or electric shock. Never 
spill liquid of any kind on the product. Do not attempt to service this product yourself because 
opening or removing covers  may expose you to dangerous voltage points and other risks and 
may void your warranty. Refer all servicing to a Brother Authorized Service Center. For the 
location of your nearest Brother Authorized Service Center, please call 
In USA : 1-800-284-4357
In Canada : 1-877-BROTHER.
(See  Brother numbers  on page i.)
 
						

							46
15 Unplug this product from the AC power outlet and refer all servicing to Brother Authorized Service Personnel under the following conditions:
„ When the power cord is damaged or frayed.
„ If liquid has been spilled into the product.
„ If the product has been exposed to rain or water.
„ If the product does not operate normally w hen the operating instructions are followed. 
Adjust only those controls that are covered by the operating instructions. Improper 
adjustment of other controls may result in  damage and will often require extensive work by 
a qualified technician to restore the product to normal operation.
„ If the product has been dropped or the cabinet has been damaged.
„ If the product exhibits a distinct change in performance, indicating a need for service.
16 To protect your product against power surges,  we recommend the use of a power protection 
device (Surge Protector).
17 To reduce the risk of fire, electric shock and injury to people, note the following: „Do not use this product near appliances that use water, a swimming pool or in a wet 
basement.
„ Do not use the machine during an electrical storm (there is the remote possibility of an 
electrical shock).
 
						

							Safety and Legal47
TrademarksA
The Brother logo is a registered trademark of Brother Industries, Ltd.
Brother is a registered trademark of Brother Industries, Ltd.
Multi-Function Link is a registered trademark of Brother International Corporation.
Windows and Microsoft are registered trademarks of Microsoft in the U.S. and other countries.
Macintosh and TrueType are registered trademarks of Apple Computer, Inc.
PaperPort is a registered trademark of ScanSoft, Inc.
Presto! PageManager is a registered trademark of NewSoft Technology Corporation.
BROADCOM, SecureEasySetup and the SecureEasySetup logo are trademarks or registered 
trademarks of Broadcom Corporation in the United States and/or other countries.
Java and all Java-based trademarks and logos are  trademarks or registered trademarks of Sun 
Microsystems, Inc. in the United States and other countries.
Each company whose software title is mentioned in this manual has a Software License 
Agreement specific to its proprietary programs.
All other brand and product names mentioned in this User’s Guide, the Software User’s 
Guide, and the Network User’s Guide are registered trademarks of their respective 
companies.
 
						

							48
B
OptionsB
This machine has the following optional accessories. You can increase the capabilities of the 
machine with these items.
OptionsB
Lower tray unitDIMM memory
LT-5300