Brother DCP 8045D User Manual

USING THE DCP AS A PRINTER   6 - 4
Manual Duplex Printing
The DCP prints all the 
even-numbered pages on one 
side of the paper first. 
Then, the Windows
® driver 
instructs you (with a pop-up 
message) to reinsert the paper. 
Before reinserting the paper, 
straighten it well, or you may get 
a paper jam. Very thin or very 
thick paper is not recommended. 
We recommend 20 to 24 lb 
(75 to 90 g/m
2) paper.
Face-down output tray
The DCP ejects paper with printed surfaces face down into the 
output tray in...

6 - 5   USING THE DCP AS A PRINTER
Printing on plain paper
The manual feed tray (For DCP-8040)
1Select the Paper Size, Media Type, Paper Source, and other 
settings in the printer driver.
Media Type: Plain Paper
Paper Source: Manual
2Send the print data to the DCP.
3Open the manual feed tray. Slide the paper guides to fit the 
paper size.
4Using both hands put paper in the manual feed tray until the 
front edge of the paper touches the paper feed roller and the 
DCP grips the paper.
5After the printed...

USING THE DCP AS A PRINTER   6 - 6
The MP tray (For DCP-8045D)
1Select the Paper Size, Media Type, Paper Source, and other 
settings in the printer driver.
Media Type: Plain Paper
Paper Source: MP Tray
2Open the MP tray and lower it gently.
3Pull out the MP tray support flap.
4When loading paper in the MP tray, make sure it touches the 
back of the tray. 
5While pressing the paper-guide release lever, slide the paper 
guide to fit the paper size.
6Send the print data to the DCP.
Make sure that the paper...

6 - 7   USING THE DCP AS A PRINTER
Printing on thicker paper and card stock 
When the back output tray is pulled down, the DCP has a straight 
paper path from the manual feed tray or the MP tray through to the 
back of the DCP. Use this paper feed and output method when you 
want to print on thicker paper or card stock.
The manual feed tray (For DCP-8040)
1Select the Paper Size, Media Type, Paper Source, and other 
settings in the printer driver.
Media Type: Thick paper or Thicker paper
Paper Source:...

USING THE DCP AS A PRINTER   6 - 8
5Send the print data to the DCP.
6After the printed page comes out of the DCP, put in the next 
sheet of paper as in Step 4 above. Repeat for each page that 
you want to print.
7When you have finished the print job, close the back output tray.
Caution
Remove each sheet immediately after printing. Stacking the sheets 
may cause a paper jam or the paper to curl.
 

6 - 9   USING THE DCP AS A PRINTER
The multi-purpose tray (MP tray) (For DCP-8045D)
1Select the Paper Size, Media Type, Paper Source, and other 
settings in the printer driver.
Media Type: Thick paper or Thicker paper
Paper Source: MP Tray
2Open the back output tray, and then pull out the face-up output 
tray support if necessary.
3Open the MP tray and lower it gently.
4Pull out the MP tray support flap.
5When putting paper in the MP tray, make sure it touches the 
back of the tray.
6While pressing the...

USING THE DCP AS A PRINTER   6 - 10
7Send the print data to the DCP.
8When you have finished the print job, close the back output tray.
Caution
Remove each sheet immediately after printing. Stacking the 
sheets may cause a paper jam or the paper to curl.
 

6 - 11   USING THE DCP AS A PRINTER
Printing on envelopes
To print on envelopes use manual feed tray or multi-purpose tray.
1Select the Paper Size, Media Type, Paper Source, and other 
settings in the printer driver.
Media Type: Envelope, Env.thin or Env.thick
For DCP-8040:
2 Open the back output tray.
■The DCP automatically turns on the Manual Feed mode 
when you put paper in the manual feed tray.
■All sides should be properly folded without any wrinkles or 
creases.
 

USING THE DCP AS A PRINTER   6 - 12
3Open the manual feed tray. Slide the paper guides to fit the 
envelope size.
4Using both hands put the envelope in the manual feed tray until 
the front edge of the envelope touches the paper feed roller. 
Hold the envelope in this position until the DCP automatically 
feeds it in for a short distance, and then let go of the envelope.
If envelopes are creased after they have been printed:
At the back of the DCP, open the back output tray and push 
down the blue tabs...

6 - 13   USING THE DCP AS A PRINTER
5After the printed envelope comes out of the DCP, the DCP will 
wait until you put in the next envelope. Repeat Step 4 for each 
envelope you want to print.
6Send the print data to the DCP.
7After you finish the print job, close the back output tray.
For DCP-8045D:
2Open the back output tray, and then unfold the face-up output 
tray support if necessary.
3Open the MP tray and lower it gently.
■Make sure the envelope is straight as you insert it in the 
manual feed...