Brother DCP 8045D User Manual

INTRODUCTION   1 - 11
4Adjust the paper guides to fit the width of your originals.
5Press Start. The DCP starts scanning the first page.
ADF Document 
Output Support Flap
The documents 
are Face Up
in the ADF
 

1 - 12   INTRODUCTION
Using the scanner glass
You can use the scanner glass to copy one page at a time, or pages 
of a book. To use the scanner glass, the ADF must be empty. You 
can make multiple copies; however, if you want them sorted you 
must use the ADF.
1Lift the document cover.
2Using the document guidelines on the left, center the orignal 
face down on the scanner glass and close the document cover.
3Using the numeric keys, enter the number of copies you want 
(up to 99).
4Press Start.
The DCP...

PAPER   2 - 1
2
About paper
Type and size of paper
The DCP loads paper from the installed paper tray, manual feed tray, 
multi-purpose tray or optional lower tray.
Recommended paper
■Before you buy a large amount of paper, please test some to 
make sure that the paper is suitable.
■Use paper that is made for plain-paper copying.
■Use paper that is 75 to 90 g/m2 (20 to 24 lb).
■Use neutral paper. Do not use acidic or alkaline paper.
■Use long-grain paper.
■Use paper with a moisture content of...

2 - 2   PAPER
Caution
Do not use ink jet paper. It may cause a paper jam and damage your 
DCP. 
Choosing acceptable paper
We recommend that you test paper (especially special sizes and 
types of paper) on the DCP before purchasing large quantities.
■Avoid feeding label sheets that are partly used or your DCP will 
be damaged.
■Avoid using coated paper, such as vinyl coated paper.
■Avoid using preprinted or highly textured paper, or paper with an 
embossed letterhead.
For optimum printing, use a...

PAPER   2 - 3
Paper capacity of the paper trays
Paper size Number of sheets
Multi-purpose tray 
(MP tray)
(DCP-8045D)Width: 2.75 to 8.66 in. 
(69.8 to 220 mm)
Height: 4.57 to 16.0 in. 
(116 to 406.4 mm)50 sheets 
(20 lb or 80 g/m
2)
Manual feed tray
(DCP-8040)Width: 2.75 to 8.66 in. 
(69.8 to 220 mm)
Height: 4.57 to 16.0 in. 
(116 to 406.4 mm)Single sheet
Paper tray (Tray #1)A4, Letter, Legal, B5 (ISO), 
B5 (JIS), Executive, A5, A6, 
B6 (ISO)250 sheets 
(20 lb or 80 g/m
2)
Optional lower tray 
(Tray...

2 - 4   PAPER
Paper specifications for each paper tray
*1 Up to 3 envelopes
*2 Up to 10 sheetsModel DCP-8040 DCP-8045D
Paper 
typesMulti-
purpose 
trayN/A Plain paper, Bond paper, 
Recycled paper, 
Envelope
*1, Labels*2, and 
Transparency*2
Manual 
feed trayPlain paper, Bond paper, 
Recycled paper, 
Envelope, Labels, and 
TransparencyN/A
Paper tray  Plain paper, Recycled paper, and Transparency
*2 
Optional 
Lower tray Plain paper, Recycled paper, and Transparency*2 
Paper 
weightsMulti-
purpose 
trayN/A...

PAPER   2 - 5
How to load paper
To load paper or other media in the paper tray
1Pull the paper tray completely out of the DCP.
2While pressing the paper guide release lever, slide the adjusters 
to fit the paper size.
Check that the guides are firmly in the slots.
For Legal size paper, press the universal guide release button 
and pull out the back of the paper tray.
Universal Guide Release 
Button
 

2 - 6   PAPER
3Fan the stack of paper well to avoid paper jams and misfeeds.
4Put paper in the paper tray.
Check that the paper is flat in the tray, below the maximum 
paper mark, and that the paper guide is flush against the paper 
stack.
5Put the paper tray firmly back in the DCP and unfold the support 
flap before you use the DCP.
When you put paper in the paper tray, please remember the 
following
■The side to be printed on must be face down.
■Put the leading edge (top of the paper) in first and push...

PAPER   2 - 7
To load paper or other media in the manual feed tray 
(For DCP-8040)
1Open the manual feed tray. Slide the paper guides to fit the 
paper size.
2Using both hands put paper in the manual feed tray until the 
front edge of the paper touches the paper feed roller. Hold the 
paper in this position until the DCP automatically feeds the 
paper in for a short distance, and then let go of the paper.
When printing envelopes and labels you should only use the 
manual feed tray.
 

2 - 8   PAPER
When you put paper in the manual feed tray, please remember 
the following
■The side to be printed on must be face up.
■Put the leading edge (top of the paper) in first and push it 
gently into the tray.
■Make sure that the paper is straight and in the proper 
position on the manual feed tray. If it is not, the paper may 
not be fed properly, resulting in a skewed printout or a paper 
jam.
■Do not put more than one sheet of paper or envelope in the 
manual feed tray at any one time, or it...