Barco Rlm R6+ Performer Owners Manual

							13. Display Setup
13.8.4 ScenergiX overlap zone (vertical scenergix)
Definitions
Image 13-17
Scenergix overlap zone vertical
Overlap : number of pixels that overlap
Vertical resolution of 1 projector : 768 for Graphics versions, 1024 for Reality versions, 1050 for SXGA projectors.
Total vertical screen resolution : [(Vertical resolution of 1 projector) x 2] minus (overlap)
Vertical Resolution source : number of active lines of the source
Adjustment of Active lines (Lact) of the first projector
1. Go to File –> Edit menu of first projector.
2. Enter value for vertical act (= Lact) as follows :
Lact = [(vert.. resolution of 1 projector)/(Total Vert. screen resolution)] x (Verti. resolution source)
3. Vertical start (= Lstart) remains the same.
Adjustment of Active lines (Lact) of second projector
1. Go to File –> Edit menu of second projector.
2. Enter value for vertical act (= Lact) as follows :
Lact = [(Vert.. resolution of 1 projector)/(Total vert. screen resolution)] x (vert. resolution source)
3. Vertical start (= Lstart) = original start + [(Vert. resolution source) minus (newly calculated Lact)]
Example
Vertical resolution source : 1200 lines
Vertical resolution projector 1 & 2: 768 lines
Overlap : 50 lines
Total vertical screen size : 1486 lines
Lact projector 1 = (768 / 1486) x 1200 = 620 lines
Lact projector 2 = (768 / 1486/) x 1200 = 620 lines
Lstart projector 2 = Lstart projector 1 + (1200 – 620)
13.8.5 ScenergiX border adjustment
What can be done with the ScenergiX border menu?
Within this menu the width of the blending zone is set up.
How to select a border?
1. PressMENUto activate the menu bar.
2. Press→to select theDisplay setupitem. (image 13-18)
R5976816 RLM R6+ PERFORMER 21/12/2005
127 
						

							13. Display Setup
3. Press↓to pull down theDisplay setupmenu.
4. Use↑or↓to selectScenergiX.
5. Press→to select theScenergiXitem.
6. Use↑or↓to selectBorder.
7. PressENTERto select.
A dialog box will be displayed. The actual scenergix border will be displayed.
8. Use↑or↓to select the desired adjustment.
Image 13-18
Adjusting with the arrow keys.
1. When on an adjustment, use the→or←key to move the border line to the desired position.
The border line will move in the desired direction and the light output in the overlap area will be adapted to. (image 13-19)
Set first the width of the first projector and repeat for the second one.(image 13-20, image 13-21)
Image 13-19
Width selections
128R5976816 RLM R6+ PERFORMER 21/12/2005 
						

							13. Display Setup
Image 13-20
Width set up for projector 1
Image 13-21
Width set up for projector 2
Adjusting by entering the exact values.
1. When on an adjustable item, the input box background will be colored. PressENTER.
The value will change to a 3 digit value and the first digit is selected.
2. Enter a value with the digit keys on the remote control.
The cursor jumps automatically to the next digit.
3. PressENTERto activate the new value.
Use reset to return to the default settings.
13.8.6 Black level of the images
Why
For dark images, the overlap zone will be brighter then the rest of the images. Therefore we can rise the black level of the remaining
image (excluding the overlap zone)
How to adjust
1. PressMENUto activate the menu bar.
R5976816 RLM R6+ PERFORMER 21/12/2005
129 
						

							13. Display Setup
2. Press→to select theDisplay setupitem. (image 13-22)
3. Press↓to pull down theDisplay setupmenu.
4. Use↑or↓to selectScenergiX.
5. Press→to select theScenergiXitem.
6. Use↑or↓to selectBlack level.
7. PressENTERto select.
A dialog box will be displayed on a black level background.
Adjust the black level of area A until the black level of area A, B and C or equal (area C should be adjusted on the second
projector). (image 13-23)
Use the up or down arrow key to select the adjustment (All, Red, Green or Blue)
Use the left or right arrow key to select the adjustment direction and speed.
PressENTERto increment or decrement the value. Stay pressing onENTERuntil the desired value is reached.
Image 13-22
ACB
12
13
11R
G
BRGB
Image 1Image 2
Image 13-23
Black level adjustment
130R5976816 RLM R6+ PERFORMER 21/12/2005 
						

							14. Installation menu
14. INSTALLATION MENU
Overview
• Lens adjustments
• Projector address
• Orientation
• Language
• Quick access keys
• RS baudrate
• RS mode
• Automatic startup
• Security
14.1 Lens adjustments
What can be done ?
Motorized lenses can be adjusted in the installation menu or via the dedicated keys on the remote (see chapter “Getting Started”,
“Quick lens adjustment”).
The following parameters can be adjusted:
•Zoom
• Focus
• Shift (also for non motorized lenses)
How to Zoom/focus or shift ?
1. PressMENUto activate the menu bar.
2. Press→to select theInstallation. (image 14-1)
3. Press↓to pull down theInstallationmenu.
4. Use↑or↓to selectLens adjustment.
5. PressENTERto start zoom/focus adjustment.
A text box appears on the screen. (image 14-2)
↑or↓
Lens zoom
←or→
Lens focus
ENTER
to switch the cursor key between zoom/focus and vertical/horizontal shift.
Logo
to switch the image between active source or test pattern
6. PressENTERto switch to the shift mode.
See image 14-3.
←or→
Horizontal shift
↑or↓
Vertical shift
ENTER
to switch the cursor key between vertical/horizontal shift and zoom/focus
Logo
to switch the image between active source or test pattern
R5976816 RLM R6+ PERFORMER 21/12/2005131 
						

							14. Installation menu
Image 14-1
Lens adjustment
Use 
↑ and ↓ for zoom
Use 
← and → for focus
Press  for SHIFT mode
Press  or 
for test pattern
Image 14-2
Lens adjustment
Use 
↑ and ↓ for vertical shift
Use 
← and → for horizontal shift
Press  for ZOOM/FOCUS
Press  or 
for test pattern
Image 14-3
14.2 Projector address
What can be done ?
In some cases the projector address must be changed, for example if an unique RCU is used to control 2 or more projectors in a
room.
The projector address setting on the projector must match the setting on the RCU.
What can be changed ?
Within the ’Change Projector Address’ menu, the following items can be changed
•Projector address: address defined by the user. Can be set between 0 and 255 when controlled via RS232 and between 0 and
9whencontrolledviatheRCU
• Common address : address may be 0 or 1
How to change the projector’s address ?
1. PressMENUto activate the menu bar.
2. Press→to select theInstallation. (image 14-4)
3. Press↓to pull down theInstallationmenu.
4. Use↑or↓to selectProjector address.
5. PressENTERto confirm .
A dialog box appears on the screen. Projector address is selected. (image 14-5)
6. PressENTERto go to the edit mode.
The most right digit will be selected. Use the left arrow key to jump to the other digits. (image 14-6)
7. Enter an address between 0 and 255 with the digit keys on the RCU and pressENTERto activate.
132
R5976816 RLM R6+ PERFORMER 21/12/2005 
						

							14. Installation menu
Image 14-4
Image 14-5Image 14-6
How to change the common address ?
1. PressMENUto activate the menu bar.
2. Press→to select theInstallation. (image 14-7)
3. Press↓to pull down theInstallationmenu
4. Use↑or↓to selectProjector address
5. PressENTER
A dialog box appears on the screen. Use the↑to scroll to Common RC5 address. (image 14-8)
6. PressENTERto go to the edit mode.
The digit will be selected. (image 14-9)
7. Enter the common address, 0 or 1.
Image 14-7
Image 14-8Image 14-9
R5976816 RLM R6+ PERFORMER 21/12/2005133 
						

							14. Installation menu
14.3 Orientation
Projector orientations
Depending on how the projector is oriented, the projector’s internal settings have to be adapted. See also Chapter “Installation”,
“Orientation”.
How to change the orientation ?
1. PressMENUto activate the menu bar.
2. Press→to select theInstallationitem. (image 14-10)
3. Press↓to pull down theInstallationmenu.
4. Use↑or↓to selectOrientation.
5. Press→to pull down the menu.
6. Use↓or↑to select the desired orientation.
7. PressENTERto confirm.
The projection is adapted and a white bullet shows the active configuration.
Image 14-10
14.4 Language
List of languages
The list of selectable languages depends on the software of the projector.
Standard available languages:
• English
• French
•German
• Spanish
How to change the Language ?
1. PressMENUto activate the menu bar.
2. Press→to select theInstallationitem. (image 14-11)
3. Press↓to pull down theInstallationmenu.
4. Use↑or↓to selectLanguage.
5. Press→to pull down the menu.
6. Use↓or↑to select the desired language.
7. PressENTERto confirm.
The language is adapted and a white bullet shows the active configuration.
134
R5976816 RLM R6+ PERFORMER 21/12/2005 
						

							14. Installation menu
Image 14-11
14.5 Quick access keys
What can be done ?
The 3 function keys on top of the RCU (F1, F2 and F3) can be associated with a particular item in one of the menus.
Each function which is not password protected can be associated to a function key.
How to get an overview of the quick access keys ?
1. PressMENUto activate the menu bar.
2. Press→to select theInstallation. (image 14-12)
3. Press↓to pull down theInstallationmenu.
4. Use↑or↓to selectQuick access keys.
5. PressENTER.
The quick access keys overview text box appears on the screen. (image 14-13)
Default factory pre-programmed functionsare : color, brightness and contrast.
Image 14-12
Image 14-13
How to program the quick access keys ?
1. Scroll through the menu bar to the desired menu item.
R5976816 RLM R6+ PERFORMER 21/12/2005
135 
						

							14. Installation menu
2. Push the desired function key for 3 seconds.
The menu item is stored behind the quick access key. The messageQuick Access key storedwill be displayed.
14.6 RS baudrate
How to change the RS baudrate?
1. PressMENUto activate the menu bar.
2. Press→to select theInstallationitem. (image 14-14)
3. Press↓to pull down theInstallationmenu.
4. Use↑or↓to selectRS232 baudrate
5. Press→to pull down the menu.
6. Use↓or↑to select the desired baudrate.
7. PressENTERto confirm.
Image 14-14
14.7 RS mode
How to change the mode?
1. PressMENUto activate the menu bar.
2. Press→to select theInstallationitem. (image 14-15)
3. Press↓to pull down theInstallationmenu.
4. Use↑or↓to selectRS mode
5. Press→to pull down the menu.
6. Use↓or↑to select the desired mode.
The following modes are possible:
- RS232
- RS422
- RS422 terminated
7. PressENTERto confirm.
136
R5976816 RLM R6+ PERFORMER 21/12/2005