Barco Rlm R6+ Performer Owners Manual

							12. Image Files Menu
Image 12-21
12.11Zoom-Focus
What can be done ?
As the projector is equipped with TLD lenses, it is possible to store the zoom and focus setting for each file separately.
How to set ?
1. PressMENUto activate the menu bar.
2. Press→to select theImage filesitem. (image 12-22)
3. Press↓to pull down theImage filesmenu.
4. Use↑or↓to selectZoom/Focus.
5. Press→to display the choices.
6. Use↑or↓to select desired choice.
Universal
The same zoom/focus setting will be used for all files.
Unique
The zoom/focus settings will be stored file per file.
Image 12-22
R5976816 RLM R6+ PERFORMER 21/12/2005117 
						

							12. Image Files Menu
118R5976816 RLM R6+ PERFORMER 21/12/2005 
						

							13. Display Setup
13. DISPLAY SETUP
Overview
• Full screen representation
• Startup screen
•TextBox
• Menu bar position
• Status bar position
• Sliderbox position
• Auto Image Setup
• Scenergix
13.1 Full screen representation
Purpose of the Full screen representation
TheFull screen representationfunction forces to use the complete native resolution of the DMD panels independently of the native
resolution of the source.
How to enable/disable the full screen representation ?
1. PressMENUto activate the menu bar.
2. Press→to select theDisplay setupitem. (image 13-1)
3. Press↓to pull down the Display setup menu.
4. Use↑or↓to selectFull screen representation.
5. Press→to pull down the menu.
6. Use↓or↑to selectONorOFF.
On Full screen representation is active. The source resolution will be re-scaled to fill the complete screen.
OffThe will be displayed with chosen aspect ratio.
7. PressENTER.
Image 13-1
TheShow native resolutionfunction inImage, on the other hand forces to use the native resolution of the
source. The Show native resolution function overrules the Full screen representation function.
R5976816 RLM R6+ PERFORMER 21/12/2005119 
						

							13. Display Setup
13.2 Startup screen
What can be done ?
When the startup screen is enabled, the identification screen is displayed for a few seconds at startup.
This startup screen can be disabled.
How to enable/disable the Startup screen?
1. PressMENUto activate the menu bar.
2. Press→to select theDisplay setupitem. (image 13-2)
3. Press↓to pull down theDisplay setupmenu.
4. Use↑or↓to selectStartup screen.
5. Press→to pull down the menu.
6. Use↓or↑to selectOnorOff.
On Start up screen will be displayed.
OffNo start up screen will be displayed during start up.
7. PressENTERto confirm.
Image 13-2
13.3 TextBox
What can be done ?
All menus, dialog boxes and text boxes can be disabled by putting the text box function in the off position.
How to enable/disable the Textbox ?
1. PressMENUto activate the menu bar.
2. Press→to select theDisplay setupitem. (image 13-3)
3. Press↓to pull down theDisplay setupmenu.
4. Use↑or↓to selectTextbox.
5. Press→to pull down the menu.
6. Use↓or↑to enable/disable the textbox.
7. PressENTER.
120
R5976816 RLM R6+ PERFORMER 21/12/2005 
						

							13. Display Setup
Image 13-3
To enable the menus and dialog boxes again, press the TEXT button on the RCU.
13.4 Menu bar position
What can be done ?
The menu bar can be centered vertically. The range is from the top of the screen to the middle of the screen.
This is useful in applications where the top image content is not displayed (e.g. due to blanking).
Image 13-4
Menu bar move
ANormalposition
B New position
How to center the menu ?
1. PressMENUto activate the menu bar.
2. Press→to select theDisplay setupitem. (image 13-5)
3. Press↓to pull down theDisplay setupmenu.
4. Use↑or↓to selectMenu bar position menu.
5. PressENTER.
6. Use↑or↓to position the menu bar.
R5976816 RLM R6+ PERFORMER 21/12/2005
121 
						

							13. Display Setup
Image 13-5
13.5 Status bar position
What can be done ?
The status bar (wizard menu) can be centered vertically. Therange is from the bottom of the screen to the middle of the screen.
Image 13-6
Status bar position
This is useful in applications where the bottom image content is not displayed (e.g. due to blanking).
How to center the menu ?
1. PressMENUto activate the menu bar.
2. Press→to select theDisplay setupitem. (image 13-7)
3. Press↓to pull down theDisplay setupmenu.
4. Use↑or↓to selectStatus bar position.
5. PressENTER.
6. Use↑or↓to position the status bar
Image 13-7
122R5976816 RLM R6+ PERFORMER 21/12/2005 
						

							13. Display Setup
13.6 Sliderbox position
What can be done ?
The sliderbox can be displayed anywhere on the screen. The exact location can be set in sliderbox menu due to the coarse and
fine adjustment.
How to reposition the sliderbox?
1. PressMENUto activate the menu bar.
2. Press→to select theDisplay setupitem. (image 13-8)
3. Press↓to pull down theDisplay setupmenu.
4. Use↑or↓to selectSliderbox position.
5. PressENTERto confirm.
A sliderbox is displayed. Use the 4 arrow keys to move the box to the desired position.
The X and Y coordinate will change simultaneously while moving the box. (image 13-9)
6. Quit withBACK.
Image 13-8
Sliderbox position
X position :   619   Y position :   618
Press  for fine adjustment
Image 13-9
There is a coarse and a fine adjustment of the position, use ENTER (when sliderbox is displayed) to switch
between the two.
13.7 Auto Image Setup
What can be done ?
Auto image allows to detect automatically the characteristics of the source (total pixels per line,...) and uses this information to adapt
the image to the DLP panels.
Auto image can adapt the image based on following data :
• Total pixels per line and total lines
• Start pixel and start line
• Phase
• Contrast/brightness levels
R5976816 RLM R6+ PERFORMER 21/12/2005
123 
						

							13. Display Setup
Auto image works only for data signals.
How to set up Auto Image?
1. PressMENUto activate the menu bar.
2. Press→to select theDisplay setupitem. (image 13-10)
3. Press↓to pull down theDisplay setupmenu.
4. Use↑or↓to selectAuto Image setup.
5. PressENTERto confirm.
A dialog box is displayed. (image 13-11)
6. Check first Enabled.
All other items in the list become available. (image 13-12)
7. Use the arrow keys to select the desired item and pressENTERto enable or disable that item.
Image 13-10
Image 13-11Image 13-12
How to perform Auto Image ?
1. pressAuto Imageon the RCU
A text box showing a progress bar is displayed. (image 13-13)
Image 13-13
124R5976816 RLM R6+ PERFORMER 21/12/2005 
						

							13. Display Setup
During the AUTO IMAGE measuring process the data source disappears temporarily (logo is displayed if back-
ground is set to logo)
13.8 Scenergix
Overview
• Introduction
• Preparations
• ScenergiX overlap zone (horizontal scenergix)
• ScenergiX overlap zone (vertical scenergix)
• ScenergiX border adjustment
• Black level of the images
13.8.1 Introduction
Why ScenergiX ?
When working in a multichannel setup the RLM R6+ Performer and its Soft Edge possibilities enable an image blending that gives
the appearance of a single view, thus achieving realistic immersion for the majority of wide screen applications.
Image 13-14
Why Soft Edge?
What is the Basic Principal of ScenergiX ?
The principle of edge blending is archived by linear modulation of the light output in the overlap zone so that the light output in that
zone equals the light output of the rest of the image.
Adjustable overlapping area
50% 100%50% 100%
image 2 image 1
image 2 image 1
Light output per image
Total composite light output
Image 13-15
ScenergiX Basic Principle
R5976816 RLM R6+ PERFORMER 21/12/2005125 
						

							13. Display Setup
13.8.2 Preparations
ScenergiX Preparations
To ensure proper ScenergiX adjustment, be sure that the following adjustments are done perfectly on all projectors:
• Convergence (Electronic Convergence).
• Geometry
• Color Matching (Color Temperature, Input Balance, Gamma)
13.8.3 ScenergiX overlap zone (horizontal scenergix)
Definitions
Image 13-16
Scenergix set up
Overlap : number of pixels that overlap
Horizontal resolution of 1 projector : 1024 for Graphics versions, 1280 for Reality versions, 1400 for SXGA projectors.
Total horizontal screen resolution : [(horizontal resolution of 1 projector) x 2] minus overlap.
Horizontal Resolution source : number of active pixels of the source.
Adjustment of Active pixels (Pact) of the first projector
1. Go to File –> Edit menu of first projector.
2. Enter value for horizontal active (= Pact) as follows :
Pact = [(Horz. resolution of 1 projector)/(Total horz. screen resolution)] x (horz. resolution source)
3. Horizontal start (= Pstart) remains the same.
Adjustment of Active pixels (Pact) of second projector
1. Go to File –> Edit menu of second projector.
2. Enter value for horizontal active (= Pact) as follows :
Pact = [(Horz. resolution of 1 projector)/(Total horz. screen resolution)] x (horz. resolution source)
3. Horizontal start (= Pstart) = original start + [(Horz. resolution source) minus (newly calculated Pact)]
Example
Horizontal resolution source : 1600 pixels
horizontal resolution projector 1 & 2 : 1024 pixels
Overlap : 100 pixels
Total horizontal screen size in pixels : 1948 pixels
Pact projector 1 = [(1024 / 1948)] x 1600 = 841 pixels
Pact projector 2 = [(1024 / 1948)] x 1600 = 841 pixels
Pstart projector 2 = Pstart projector 1 + (1600 – 841)
126
R5976816 RLM R6+ PERFORMER 21/12/2005