Barco Projector Cineversum 70 Quickstart Manual
Have a look at the manual Barco Projector Cineversum 70 Quickstart Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 183 Barco manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
4. Getting Started No.Key nameDescription 9*Aspect ratio button. Opens the selection menu for the aspect ratio. 10FREEZEpress to freeze the projected image. 11TEXTto des-activate or activate the on screen slide bars. 12ENTERto confirm an adjustment or selection in a menu.. Entering the adjustment mode is also possible. 13Cursor keysCursor Keys on RCU : to make item selections in a menu box or to adjust a function when a slide bar is vissible. 14EXITto leave the selected menu box or item (go upwards to previous menu). 15Audio controlsnot implemented 4.2 Switching on Howtoswitchon 1. Press the main power switch on the projector The projector goes to stand by mode. The stand by LED blinks. Start image projection 1. PressStandbykey once on the RCU. Note:It may take about 60 seconds before image projection, i.e. no projection until the completion of several operations (soft- ware initialization,...). The projector scans the inputs and displays the first found active source. 2. To switch to the desired source, press the corresponding digit on the RCU. 4.3 Lamp runtime Lamp runtime indication while running When the total runtime of the lamp is 1400 hours or more, a warning message will be displayed : “Lamp Runtime : 1400 hours”. When the total runtime of the lamp is 1500 hours or more, a second message will be displayed : “Lamp Runtime limit reached : 1500 hours”. This warning message will be repeated at next start up. PressEXITto remove this message. Contact a qualified service technician to replace the lamp. The total life time of the lamp for a safe operation is 1500 hours. Do not use it longer as the lamp could explode. The lamp runtime reset as well as the lamp replacement can only be done by a Barco authorized technician. R5976763 CINEVERSUM 60/70 2204200427
4. Getting Started 4.4 Switching from operational mode to standby Howtoswitchtostandby 1. Press the standby button on the remote control for 2 seconds. A message : “Power down appears”. Projector goes into standby. Standby LED blinks. After a while, the fans stop blowing and the projector switch off automatically. 4.5 Switching off the projector Howtoswitchtooff 1. Press the standby button on the remote control for 2 seconds. A message : Power down appears. Projector goes into standby. Standby LED blinks. After a while, the fans stop blowing and the projector switch off automatically. 2. Press the main power switch on the projector. 4.6 Temperature error DMD Overview When the temperature of the DMD is too low or too high, the projector will switch automatically to standby. The LED on the projector flashes 8 times and an automatic shutdown is activated. 4.7 Using the RCU Pointing to reflective screen Point the front of the RCU to the reflective screen surface. A C B Image 4-3 Via reflective screen Direct pointing to the IR sensors Point the RCU to any of the remote sensors, located on the front, top and the rear of the projector. The remote control can be used up to 9 meters from the projector and within a 45 degree angle with respect to the sensors. 28 R5976763 CINEVERSUM 60/70 22042004
4. Getting Started -+-+-+-+-+-+-+-+-+-+ ADJ EX IT ENT E R P AUS ETEX T ? P HASE SHA RP N BRI GHT N CON TR BAS S T RE B L E BAL A NCETIN T CO L O R F1F2F4F5F3 90 78563412 -+-+-+-+-+-+-+-+-+-+ A D J EX I T E N T E R P AU S E T EX T ?P H A S E S H A R P N B R I G H TN CO N T R B A S S T R E B L E V O L B A L A N C E T I N T CO L O R F 1F 2F 4F 5F 3 9 07 85 63 41 2 4545 Image 4-4 Direct using of the RCU Backlighting When a button is pressed on the RCU, backlight is activated automatically. That allows the user to operate the remote control in a dark room. Backlight is turned off automatically a few seconds after the last button is pressed. 4.8 Projector Address Projector address Address installed in the projector to be individually controlled. Overview The projector address can be set to any value between 0 and 9. Why a projector address ? As more than one projector or device which is remote controlled canbe installed in a room, the separate projector or device should be separately addressable with an RCU. When the projector and another device have the same address, during controlling, interference is possible. To avoid that, set the projector address on a not used address in the room. How to set the projector address ? 1. Press TheAddresskey (recessed key) with a pencil. The projector displays a message box to announce that you can enter an address between 0 and 9. 2. Enter the address by pressing a digit key between 0 and 9. The projector address and the address of the RCU will be changed to the new entered address. 3. PressEXITto return to operational mode. 4.9 Controlling the projector Input Selection Key in the corresponding input with the digit keys on the RCU. The selected source will be displayed. When an source is displayed and more sources are connected and switched on: •press↑key to display the previous source. •press↓key to display the next source. When no previous or next source, the projector returns to the actual source (only whenAuto searchis on). R5976763 CINEVERSUM 60/70 22042004 29
4. Getting Started The following key numbers are valid : 1. PC source 2. RGB/Component source (5 RCA input) 3. DVI 4. S-Video 5. Video 6. Component (3 RCA) Picture Controls When an image control is pressed, a text box with a bar scale and function name of the control, e.g. ’brightness...’ appears on the screen (only ifBarscale statusisYe s). The length of the bar scale and the value of the numeric indication indicate the current memorized setting for this source. The bar scale changes as the arrows on the RCU are pressed or the + or - buttons on the local keypad. The picture settings are saved in the image file. BrightnessUse the + button for a higher brightness. Use the - button for a lower brightness. ContrastUse the + button for a higher contrast. Use the - button for lower contrast. ColorUse the + button for richer colors. Use the - button for lighter colors. Tint (Hue)Tint is only active for Video and S-Video when usinga60Hzsource(likeNTSC4.43orNTSC3.58). Use the + button Use the - button. SharpnessUse the + button for a sharper picture. Use the - button for a softer picture. FreezePressFreezeto freeze the displayed image. The Pause Key When the Pause key is pressed, the image projection is stopped, the image is removed from the screen. To restart the image projection: •PressPAUSEkey 30 R5976763 CINEVERSUM 60/70 22042004
5. Getting used to the menu structure 5. GETTING USED TO THE MENU STRUCTURE Overview • How to start up the menus • How to use the menus • How to make an adjustment • Access Control via a password 5.1 How to start up the menus Box like menu structure The menu structure is built up with boxes which allow easy access to different parameters for setting up the projector. A menu box item can generate at its turn a menu box or it can generate an adjustment box such as a slide bar. How to activate the menu structure 1. PressADJorENTERon the RCU. The Main menu box will be displayed. (menu 5-1) Main Menu Image settings Advanced settings Installation Service 1. PC 2. RGB/Component 3. DVI 4. SVideo * 5. Video 6. Component Shutdown Back Menu 5-1 5.2 How to use the menus How to select an item 1. Use the↑or↓keys to highlight the desired item. (menu 5-2) 2. PressENTERto select. If the selected item has sub menus, this sub menu will open. If the selected item is an adjustment or selection, the adjustment or selection will be executed. 3. Use theEXITkey to close an adjustment or to return to the previous menu. Note:The menu will be closed automatically when there is no action on the menu detected about 5 seconds. 4. UseADJto quit the menu structure completely from anywhere in the menu tree. Main Menu Image settings Advanced settings Installation Service 1. PC 2. RGB/Component 3. DVI 4. SVideo * 5. Video 6. Component Shutdown Back Menu 5-2 R5976763 CINEVERSUM 60/70 2204200431
5. Getting used to the menu structure When no action is taken within a few seconds while a menu box or slide bar is displayed, the projector quits the menu structure or slide bar (adjustment). The menus inserted in this manual are always full menus: all the items are visible. Greyed out menu items are not available for the current selected source or current software version. 5.3 How to make an adjustment How to perform ? 1. Use the arrow keys to adjust the selected control. The following keys are mostly combined: -The↑and→key perform an adjustment in the positive direction (or to the right, or upwards). -The↓and←key perform an adjustment in the negative direction (or to the left, or downwards). 5.4 Access Control via a password Password protection Some items (Advanced settings, installation and service) in the Main menucan be password protected. This password protects the user against misalignment of the projector. Only the dailynecessary items are available for non experienced users. This password protection can be enabled or disabled in the servicemenu. Once the password protection is set, this password will be necessary to disable it again. The customer is allowed to create his own password. How to get access ? 1. Select a item which is password protected. TheEnter passwordbox appears with the first position highlighted. 2. Use the↑or↓keys to select first character. The characters can be alphanumeric (from 0 to 9 and from a to z). 3. PressENTERto accept. The second character will be highlighted. 4. Select the second character and pressENTERto accept. 5. Select the third character and pressENTERto continue in the adjustment mode. 32 R5976763 CINEVERSUM 60/70 22042004
6. Source Selection 6. SOURCE SELECTION Overview • Selecting a source 6.1 Selecting a source How to select 1. PressADJorENTERto start up the Main menu. (menu 6-1) An asterisk (*) is displayed before the actual selected source. 2. Push the cursor key↑or↓to highlight the desired source, e.g. 4. SVideo. 3. PressENTERto select. When the source is available, it will be selected. A dialog box appears with the message “Calibrating input ...” Main Menu Image settings Advanced settings Installation Service 1. PC 2. RGB/Component 3. DVI 4. SVideo * 5. Video 6. Component Shutdown Back Menu 6-1 R5976763 CINEVERSUM 60/70 2204200433
6. Source Selection 34R5976763 CINEVERSUM 60/70 22042004
7. Image Settings menu 7. IMAGE SETTINGS MENU Overview • Image settings menu overview • Starting the Image settings menu • Brightness • Contrast • Saturation • Tint (hue) • Sharpness • Gamma • Color Temperature • White peak 7.1 Image settings menu overview Overview • Brightness • Contrast • Saturation •Tint • Sharpness • Gamma • Color Temperature - Predefined color temperatures - Custom color balance - Color standard • White peak 7.2 Starting the Image settings menu How to start up ? 1. PressADJorENTERto start up menus. (menu 7-1) 2. Push the cursor key↑or↓to highlightImage settings. 3. PressENTERto select. TheImage settingsmenu will be displayed. (menu 7-2) Main Menu Image settings Advanced settings Installation Service 1. PC 2. RGB/Component 3. DVI 4. SVideo * 5. Video 6. Component Shutdown Back Menu 7-1 Image settings Brightness Contrast Saturation Tint Sharpness Gamma Color temperature White peak Off Back Menu 7-2 R5976763 CINEVERSUM 60/70 2204200435
7. Image Settings menu 7.3 Brightness About brightness The brightness function is used to adjust the overall light output. How to change the brightness ? 1. Push the cursor key↑or↓to highlightBrightness. (menu 7-3) 2. PressENTERto select. A slider box appears. 3. Use the cursor keys to adjust the brightness setting. ↑or→key for higher brightness (higher values). ↓or←key for lower brightness (lower values). Image settings Brightness Contrast Saturation Tint Sharpness Gamma Color temperature White peak Off Back Menu 7-3 7.4 Contrast About contrast The contrast function is used to adjust the contrast between thelight and dark areas of the displayed image. A correct ’contrast’ setting is important for good image reproduction. How to change the contrast ? 1. Push the cursor key↑or↓to highlightContrast. (menu 7-4) 2. PressENTERto select. A slider box appears. 3. Use the cursor keys to adjust the contrast setting. ↑or→key for higher contrast (higher values). ↓or←key for lower contrast (lower values). Image settings Brightness Contrast Saturation Tint Sharpness Gamma Color temperature White peak Off Back Menu 7-4 7.5 Saturation About saturation The saturation function is used to adjust the color saturation levels for Video, S-Video and component input signals. 36 R5976763 CINEVERSUM 60/70 22042004