Home > Barco > Projector > Barco Projector Cineversum 70 Quickstart Manual

Barco Projector Cineversum 70 Quickstart Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Barco Projector Cineversum 70 Quickstart Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 183 Barco manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							2. Installation Guidelines
    2. INSTALLATION GUIDELINES
    Overview
    • Safety Warnings
    • General
    • Projector Configuration and Position
    • Safety Area around projector
    • Cleaning the lens
    • Vertical lens shift
    • Battery Insertion in the Remote Control
    • Ceiling Mount assembly
    Before installing the projector, read first the safety instructions in the safety manual delivered with the pro-
    jector and also the safety pages in this manual.
    2.1 Safety Warnings
    Mercury Vapor Warnings
    Keep the following warnings in mind when using the projector. The lamp used in the projector contains mercury. In case of a lamp
    rupture, explosion there will be a mercury vapor emission. In order to minimize the potential risk of inhaling mercury vapors:
    • Ensure the projector is installed only in ventilated rooms.
    • Replace the lamp module before the end of its operational life.
    • Promptly ventilate the room after a lamp rupture, explosion hasoccurred, evacuate the room (particularly in case of a pregnant
    woman).
    • Seek medical attention if unusual health conditions occur after alamp rupture, explosion, such as headache, fatigue, shortness
    of breath, chest-tightening coughing or nausea.
    2.2 General
    Ambient Temperature Conditions.
    Careful consideration of things such as image size, ambient light level, projector placement and type of screen to use are critical to
    the optimum use of the projection system.
    Max. ambient temperature : 40°C or 104 °F
    Min. ambient temperature : 10 °C or 50 °F
    The projector will not operate if ambient air temperature falls outside this range (10°C- 40°C or 50°F-104°F).
    Storage temperature: -35°C to +65°C (-31°F to 149°F)
    Humidity Conditions
    Storage: 0 to 98 % RH Non-condensing
    Operation: 0 to 95 % RH Non-condensing
    Environment
    Do not install the projection system in a site near heat sourcessuch as radiators or air ducts, or in a place subject to direct sunlight,
    excessive dust or humidity. Be aware that room heat rises to the ceiling; check that temperature near the installation site is not
    excessive.
    Environment condition check
    A projector must always be mounted in a manner which ensures the free flow of clean air into the projectors ventilation inlets. For
    installations in environments where the projector is subject to airborne contaminants such as that produced by smoke machines or
    similar (these deposit a thin layer of greasy residue upon the projectors internal optics and imaging electronic surfaces, degrading
    performance), then it is highly advisable and desirable to have this contamination removed prior to it reaching the projectors clean
    air supply. Devices or structures to extract or shield contaminated air well away from the projector are a prerequisite, if this is not a
    feasible solution then measures to relocate the projector to a clean air environment should be considered.
    R5976763 CINEVERSUM 60/70 22042004
    7 
    						
    							2. Installation Guidelines
    Only ever use the manufacturer’s recommended cleaning kit which has been specifically designed for cleaning optical parts, never
    use industrial strength cleaners on the projector’s optics as thesewill degrade optical coatings and damage sensitive optoelectronics
    components. Failure to take suitable precautions to protect the projector from the effects of persistent and prolonged air contam-
    inants will culminate in extensive and irreversible ingrained optical damage. At this stage cleaning of the internal optical units will
    be non-effective and impracticable. Damage of this nature is under no circumstances covered under the manufacturer’s warranty
    and may deem the warranty null and void. In such a case the client shall be held solely responsible for all costs incurred during any
    repair. It is the clients responsibility to ensure at all times that the projector is protected from the harmful effects of hostile airborne
    particles in the environment of the projector. The manufacturer reserves the right to refuse repair if a projector has been subject to
    wantful neglect, abandon or improper use.
    Special Care for Laser Beams
    Special care should be used when DLP projectors are used in the same room as performant laser equipment. Direct or indirect hitting
    of a laser beam on to the lens can severely damage the Digital MicroMirror Devices™ in which case there is a loss of warranty
    Which screen type ?
    There are two major categories of screens used for projection equipment. Those used for front projected images and those for rear
    projection applications.
    Screens are rated by how much light they reflect (or transmit in the case of rear projection systems) given a determined amount
    of light projected toward them. The ‘GAIN’ of a screen is the term used. Front and rear screens are both rated in terms of gain.
    The gain of screens range from a white matte screen with a gain of 1 (x1) to a brushed aluminized screen with a gain of 10 (x10)
    or more. The choice between higher and lower gain screens is largely a matter of personal preference and another consideration
    called the Viewing angle. In considering the type of screen to choose, determine where the viewers will be located and go for the
    highest gain screen possible. A high gain screen will provide a brighter picture but reduce the viewing angle. For more information
    about screens, contact your local screen supplier.
    What image size? How big should the image be?
    The projector is designed for an optimum screen width of :
    • For CineVERSUM 60 : min 1.30 m (52”) to max 1.78 m (70”)
    • For CineVERSUM 70 : min 1.55 m (61) to max 1.98 m (78”)
    (depending on the ambient light conditions), with an aspect ratio of 16 to 9.
    Depending on the used lens, the minimum and maximum diagonal screen sizes are :
    For CineVERSUM 70
    R9010080Short throw lens (1.4 - 1.8)Min : 0.80 m (32”)Max. 6.35 m (250”)
    R9010081Long throw lens (1.8 - 2.4)Min : Wide : 1 m (40”)
    Min : Tele : 0.76 m(30”)Max : Wide : 7.60 m (300”)
    Max : Tele : 5.60 m (222”)
    For CineVERSUM 60
    R9002460Short throw lens (1.7 - 2.25)Min: 1m(39”)Max. 5 m (200”)
    R9002461Long throw lens (2.25 – 3)Min : Wide : 0.8 m (32”)
    Min : Tele : 0.60 m(24”)Max : Wide : 6.0 m (240”)
    Max : Tele : 4.50 m (178”)
    2.3 Projector Configuration and Position
    Which configuration can be used?
    The projector can be installed to project images in four different configurations:
    • Front/table
    • Rear/table
    • Front/ceiling
    • Rear/ceiling
    Positioning the projector
    • The projector should be installed perpendicular with the screen on a distance PD and water leveled in both directions. The
    mounting positions in the following image is shown for a nominal lens position.
    • Position the screen so that it is not in direct sunlight or room light. Light falling directly onto the screen washes out the colors,
    making viewing difficult . Close the curtains and dim the lights when setting up the screen in a sunny or bright room.
    • The projector lens should be centered horizontally in the middle of the screen.
    8
    R5976763 CINEVERSUM 60/70 22042004 
    						
    							2. Installation Guidelines
    Try to avoid an inclination of the projector (forwards, backwards, to the left or to the right) as this will result in
    a keystone deformation of the image. This deformation can be corrected with the keystone function but with
    a loss of resolution as result.
    The drawing is given for a table mounted projector. The same is valid for a ceiling mounted projector.
    PD
    V1
    V2
    V3SH
    CD
    B
    C
    SWPD
    Image 2-1
    Table mounted configuration
    V1 Side view
    V2 Top view
    V3 Back view
    PD Distance projector - screen
    CD Distance bottom side projector - floor
    SH Screen height
    B Distance bottom side screen - floor
    C Distance bottom side projector - perpendicular light axes
    SW Screen width
    For CineVERSUM 70:
    LensPDCD
    1.4 - 1.8Wide : PD = 1.4 x SW
    Te l e : P D = 1 . 8 x S WCD=B+C-5.9cm
    1.8 - 2.4Wide : PD = 1.8 x SW
    Te l e : P D = 2 . 8 x S WCD=B+C-5.9cm
    With C = 0.25 x SH
    R5976763 CINEVERSUM 60/70 22042004
    9 
    						
    							2. Installation Guidelines
    For CineVERSUM 60:
    LensPDCD
    1.7 - 2.25Wide : PD = 1.7 x SW
    Tele : PD = 2.25 x SWCD=B+C-5.9cm
    2.25 - 3Wide : PD = 2.25 x SW
    Te l e : P D = 3 x S WCD=B+C-5.9cm
    With C = 0.23 x SH
    2.4 Safety Area around projector
    Safety area
    Make sure the projector is located so that the air inlets and outlets for the cooling system are not obstructed. Leave at least 50 cm
    between the projector and an object next to the projector.
    A
    B
    Image 2-2
    Do not place inflammable materials within the safety area.
    2.5 Cleaning the lens
    To minimize the possibility of damaging the optical coating or scratching exposed lens surface, we have de-
    veloped recommendations for cleaning the lens. FIRST, we recommend you try to remove any material from
    thelensbyblowing it off with clean, dry deionized air. DO NOT use any liquid to clean the lenses.
    Necessary tools
    To r a y s e eTMcloth, order number : R379058.
    Howtocleanthelens?
    Proceed as follow :
    1. Always wipe lenses with a CLEAN Toraysee
    TMcloth.
    2. Always wipe lenses in a single direction.
    Warning:Do not wipe back and forwards across the lens surface as this tends to grind dirt into the coating.
    3. Do not leave cleaning cloth in either an open room or lab coat pocket, as doing so can contaminate the cloth.
    4. If smears occur when cleaning lenses, replace the cloth. Smears are the first indication of a dirty cloth.
    Do not use fabric softener when washing the cleaning cloth or softener sheets when drying the cloth.
    Do not use liquid cleaners on the cloth as doing so will contaminate the cloth.
    10R5976763 CINEVERSUM 60/70 22042004 
    						
    							2. Installation Guidelines
    Other lenses can also be cleaned safely with this TorayseeTMcloth.
    2.6 Vertical lens shift
    What can be done ?
    The image can be shifted in a vertical way to position the image correctly on the screen.
    Necessary tools
    Spanner delivered in the package
    How to shift the lens ?
    1. Turn the lens shift bolt on the bottom side of the projector, just below the lens, until the desired image position is obtained.
    (image 2-3)
    When table mounted, turning to the left (clockwise) will shift the image upwards. Turning to the right (counter clockwise), will shift
    the image downwards.
    AImage 2-3
    Vertical lens shift bolt
    A Lens shift bolt
    R5976763 CINEVERSUM 60/70 22042004
    11 
    						
    							2. Installation Guidelines
    Vertical lens shift ranges
    A
    B
    SH
    SH
    Image 2-4
    Vertical lens shift
    The distance between the middle of the projected image and the perpendicular line from the projector.
    For CineVERSUM 60 :
    • A = 0.275 x SH
    •B=0.86xSH
    For CineVERSUM 70 :
    •A=0.24xSH
    • B = 0.625 x SH
    2.7 Battery Insertion in the Remote Control
    Where to find the batteries
    The batteries are not placed in the remote control to avoid remote control operation in its package, resulting in a shorter battery life
    time.
    How to install the batteries
    1. Push the cover tab (A) with the fingernail a little backwards and pull upwards the cover top (B). (image 2-5)
    2. Slide the cover forwards to remove. (image 2-6)
    3. Push the battery body towards the spring and lift it up to remove. (image 2-7)
    4. Insert two AA size batteries, making sure the polarities match the + and – marks inside the battery compartment (image 2-7).
    5. Insert the lower tab of the battery cover in the gap at the bottom of the remote control, and press the cover until it clicks in place
    (image 2-6).
    12
    R5976763 CINEVERSUM 60/70 22042004 
    						
    							2. Installation Guidelines
    Image 2-5
    Battery cover unlock
    Image 2-6
    Battery cover removal
    Image 2-7
    Battery removal
    2.8 Ceiling Mount assembly
    Overview
    Aceiling mount is available to mount the projector to the ceiling. Always use this ceiling mount.
    Order number : R9852060
    For a more detailed description on how to mount the ceiling mount, consult the ceiling mount installation manual (R5976750) which
    can be found in the box of the ceiling mount assembly or separately ordered by Barco.
    R5976763 CINEVERSUM 60/70 22042004
    13 
    						
    							2. Installation Guidelines
    14R5976763 CINEVERSUM 60/70 22042004 
    						
    							3. Connections
    3. CONNECTIONS
    Overview
    • Removing the Connector cover
    • Power Connection
    • Input facilities
    • S-Video input
    • Composite Video input
    • 5-Cable input
    • Component Input
    • Digital Visual Interface (DVI) input
    • Computer input (RGB analog)
    • RS232-422 IN connection
    • Trigger outputs
    3.1 Removing the Connector cover
    What is behind this cover ?
    The power connector and all inputs are situated behind this cover.
    How to remove the cover ?
    1. Loosen the locking screw. (image 3-1)
    2. Left up at the bottom and pull on the cover to loose.
    The cover makes a loud ’snap’ when removed. This is normal and does not damage the cover.
    Image 3-1
    Removing the input cover
    When all connections are done, close the cover again and fix the locking screw.
    3.2 Power Connection
    AC Power (mains) cord connection
    Use the supplied power cord to connect your projector to the wall outlet.
    Plug the female power connector into the male connector at the back of the projector.
    Plug the male connector into wall outlet.
    R5976763 CINEVERSUM 60/70 22042004
    15 
    						
    							3. Connections
    ASPECT
    RATIO
    12V TRIGGERSCREENS-VIDEO VIDEO VHR/PrB/Pb
    G/Y
    Pr Pb Y
    RS232/RS422
    IN CONTROL
    DVI INPUT
    VGA INPUT COMPONENT VIDEO INPUT RGB/COMPONENT INPUT
    Image 3-2
    The power input is auto-ranging from 90 to 240 VAC.
    About the power cord
    Mainslead(ACPowercord)withCEE7plugupto16A
    The colors of the mains lead are colored in accordance with the following code:
    • Green-and-yellow: Earth (safety earth)
    • Blue: Neutral
    •Brown:Line
    3.3 Input facilities
    Overview
    •S-Video
    • Video
    • 5 cable input on RCA
    -RGBS
    -RGBHV
    - Component video (Pr/Y/Pb)
    • Component input on 3 RCA
    •DVIinput
    • VGA input (=analog RGB)
    • Communication connections
    - RS232/RS422
    - Aspect ratio
    16
    R5976763 CINEVERSUM 60/70 22042004 
    						
    All Barco manuals Comments (0)

    Related Manuals for Barco Projector Cineversum 70 Quickstart Manual