Home > Barco > Projector > Barco Projector Cineversum 110 Quickstart Manual

Barco Projector Cineversum 110 Quickstart Manual

Here you can view all the pages of manual Barco Projector Cineversum 110 Quickstart Manual. The Barco manuals for Projector are available online for free. You can easily download all the documents as PDF.

Page 41

4. Getting Started
ON
OFFLamp 1
Lamp 2
Runtime(hrs)
Lamp Status
X(Lamp Take Over)
X-30 (W ARNING)2X-30 (W ARNING)2X (ALERT)
ON
OFFLamp 1 +Lamp 2
Runtime(hrs)
Lamp Status
X-30 (W ARNING)X (ALERT)
A
B
Image 4-4
Lamp runtime management
A Single lamp mode
B Dual lamp mode
x Maximum lamp runtime
In single mode, a lamp switch will be executed as far as the secondlamp has not reached its maximum runtime.
WARNING:Using a lamp for more than x hours is dangerous as the lamp could explode.
The lamp runtime reset as...

Page 42

4. Getting Started
Ambient temperature range within the operating temperature range of the DMD is situated : +10°C and +40°C.
4.7 Using the RCU
Pointing to a reflective screen
1. Point the front of the RCU to the reflective screen surface. (image 4-5)
F
1F
2F
3
F
4
F
5
A
DJ
E
X
I
T
E
N
T
E
R
P
A
U
S
E
P
H
A
S
E T
E
X
T
S
H
A
RP
N
T
I
N
T
C
O
L
O
R
B
R
I
G
H
T
N
C
O
N
T
R
T
R
E
B
L
EB
A
L
A
N
C
E
B
A
S
S
V
OL9
0
7856
3
4
12
IR Sensor (C)
Screen (B) Remote Control (A)
Image 4-5
Pointing RCU to the screen
A...

Page 43

4. Getting Started
1
2
ABC
D
2
3
1
Image 4-7
Stereo jack pin configuration
A tip: Left channel
B ring: right channel
C screen: common (GND)
Dexternalswitch
1Stereojack
2 Mono jack
The Remote connection uses a standard two wire cable terminated on each end with a 3.5 mm male
(mono/stereo) phone jack.
This cable is not delivered but is available in most electronic or audio shops.
Directly to one of the IR sensors
1. When using the wireless remote control, make sure you are within the effective operating...

Page 44

4. Getting Started
Common address
Default address. Projector will always execute the command coming from a RCU programmed with that common
address.
Why a projector address ?
As more than one projector can be installed in a room, the separate projector should be separately addressable with an RCU or
computer. Therefor each projector has its own address.
Set up an individual Projector Address.
The set up of a projector address can be done via the software.
Projector controlling.
Every projector requires an...

Page 45

4. Getting Started
Contrast
20
0
100
Image 4-9
BrightnessUse the + button for a higher brightness.
Use the - button for a lower brightness.
ContrastUse the + button for a higher contrast.
Use the - button for lower contrast.
ColorUse the + button for richer colors.
Use the - button for lighter colors.
Tint (Hue)Tint is only active for Video and S-Video when using the NTSC 4.43 or NTSC 3.58 system.
Use the + button
Use the - button.
SharpnessUse the + button for a sharper picture.
Use the - button for a...

Page 46

4. Getting Started
A2
D
A
A1
1
2
...... Installation ......Lens adjustment
Projector address
......
Lens adjustment
Use 
↑ and ↓ for zoom
Use ← and → for focus
Press  for SHIFT mode
Press  or 
for test pattern
Lens adjustment
Use 
↑ and ↓ for vertical shift
Use ← and → for horizontal shift
Press  for ZOOM/FOCUS
Press  or 
for test pattern
B
C
3
Lens adjustment
Use ↑ and ↓ for zoom
Use ← and → for focus
Press  for SHIFT mode
Press  or 
for test pattern
Lens adjustment
Use ↑ and ↓ for verti cal shi ft
Use...

Page 47

4. Getting Started
AB
CD
Image 4-12
Digital zoom
A Normal image
B Digital zoom out
C Digital zoom in
D Panning of the zoomed image
To return to the normal image, press MENU, go toTools, selectPiP selectand checkFull screen.
R5976697 CINEVERSUM™ 110 12/05/200443 

Page 48

4. Getting Started
44R5976697 CINEVERSUM™ 110 12/05/2004 

Page 49

5. Getting used with the Menu structure
5. GETTING USED WITH THE MENU STRUCTURE
5.1 How to start up the menus
PC like menu structure
The CineVERSUM™ 110 has a build in “PC like” menu bar which allows easy access to different parameters for setting up the
projector.
How to activate
1. PressMENUon the RCU.
The menu bar will be displayed on the screen.
Menu items which are greyed out are not accessible for the current displayed source.
5.2 Using the menu
Menu Layout
The existence of a submenu is indicated...

Page 50

5. Getting used with the Menu structure
How to pull down a submenu ?
1. Use→to pull down a submenu.
How to exit the submenu ?
1. PressBACKto exit a submenu.
Press MENU to exit the menu
5.3 Using the Dialog boxes
How to use the dialog boxes ?
Some parameters are modified by means of a dialog box, where selections can be made and/or values can be entered.
The values can be entered in several ways:
Entering numeric values using the numeric keys on the remote control
1. PressENTERto activate the input field....
Start reading Barco Projector Cineversum 110 Quickstart Manual

Related Manuals for Barco Projector Cineversum 110 Quickstart Manual

All Barco manuals