Barco Projector Cineversum 110 Quickstart Manual

1. Packaging and Dimensions
1.3 Dimensions
Side view
315
[12,40]
691,7
[27,23]
217,2
[8,55] 160
[6,30]
257
[10,118] 25
[0.984]
Image 1-3
Side view
Back view
605,2
[23,83]
225
[8,86]225
[8,86]
Air  outlet
Image 1-4
Back view
R5976697 CINEVERSUM™ 110 12/05/20047 

1. Packaging and Dimensions
Bottom view
450[17 72]
315[12 40]
Air Inlet
Cable intrance
Image 1-5
Bottom view
8R5976697 CINEVERSUM™ 110 12/05/2004 

2. Installation Guidelines
2. INSTALLATION GUIDELINES
Overview
• Safety Warnings
• General
• Safety Area around projector
• Projector Configuration
• Installation requirements and attention points
• Lenses
• Ceiling mount support for CineVERSUM™ 110
• Battery Insertion in the Remote Control
WARNING:Before installing the projector, read first the safety instructions in the safety manual delivered
with the projector and also the safety pages in this manual.
2.1 Safety Warnings
Mercury Vapor Warnings
Keep...

2. Installation Guidelines
Environment
Do not install the projection system in a site near heat sources such as radiators or air ducts, or in a place subject to direct sunlight,
excessive dust or humidity. Be aware that room heat rises to the ceiling; check that temperature near the installation site is not
excessive.
Environment condition check
A projector must always be mounted in a manner which ensures the free flow of clean air into the projectors ventilation inlets. For
installations in environments...

2. Installation Guidelines
Image 2-1
Air flow, safety area
2.4 Projector Configuration
Which configuration can be used?
The projector can be installed to project images in four different configurations:
• Front/table
• Rear/table
• Front/ceiling
• Rear/ceiling
Positioning the projector
The projector should be installed perpendicular to the screen on a distance PD and water leveled in both directions. The mounting
positions in the following image is shown for a nominal lens position. The drawing is given...

2. Installation Guidelines
PDA
B
C
PD
16 9SW
Image 2-2
Projector distance screen – projector
Due to the lens shift functionality, it is possible to mount the projector out of axis in horizontal and in vertical direction.
The lens shift can be defined as : the distance from the middle of the lens to the horizontal or vertical center line of the screen. The
Vertical lens shift is expressed in % of the screen height divided by 2.
The horizontal lens shift is expressed in % of the screen width divided by 2....

2. Installation Guidelines
Optical Axis Projector Lens
16
9
1
2
Optical Axis Projector Lens
16
9
Image 2-3
Lens shift
1 Vertical lens shift
2 Horizontal lens shift
2.5 Installation requirements and attention points
Overview
• Position the projector perpendicular to the screen and leveled to achieve an optimal image. An inclination of the projector is
allowed but limited due to the maximum keystone correction range.
• A swing of the projector is limited to 10° in both directions (due to the lamp position...

2. Installation Guidelines
2.6 Lenses
Overview
• Lenses
• Lens formulas
• Lens installation
• Cleaning the lens
2.6.1 Lenses
Available lenses
CineVERSUM™ lenses :
LensesOrder number
CineVERSUM™ (0.64)R9832640
CineVERSUM™(1.2 - 1.44 : 1)R9842342
CineVERSUM™(1.44 - 1.8 : 1)R9842343
CineVERSUM™(1.8 - 2.4 : 1)R9842344
CineVERSUM™(3.6 - 5.6 : 1)R9842346
Cinema lenses :
LensesOrder number
HC TLD(0.8)R9840901
HC TLD(1.6 - 2)R9642060
HC TLD(2 - 2.8)R9642080
CV TLD(2.8 - 5)R9842349
HC TLD(5 - 8)R9642120
2.6.2...

2. Installation Guidelines
LensesMetric formulas
(meter)Inch formulas
(inch)Hor. shiftVe r t . s h iftScreen size
(diagonal)
CineVER-
SUM™(3.6 - 5.6 :
1)WidePD = 3.6 x SWPD = 3.6 x SW-67% – +46%-50% – +143%
Te l ePD = 5.6 x SWPD = 5.6 x SW-55% – +50%-43% – +149%
173 – 724 cm
68 - 285 in
Cinema lenses :
LensesMetric formulas
(meter)Inch formulas
(inch)Hor. shiftVe r t. s hif tScreen size
(diagonal)
TLD(0.8)PD = 0.8 x SWPD = 0.8 x SW-45% – +37%-50% – +94%178–508cm
70 - 200 in
HC TLD(1.6-2)WidePD = 1.8 x...

2. Installation Guidelines
About horizontal and vertical shift
Image 2-5
Lens shift
What can be learned out of this diagram ?
When shifting completely to vertical+ or vertical -, there is no horizontal shift possible. For maximum vertical shift, the lens should
be horizontally in the middle.
When shifting completely to e.g. horizontal +, there is no vertical shift possible. For maximum horizontal shift, the lens should be
vertically in the middle.
That means :
if the horizontal shift is↑, the maximum...