Avaya Partner Advanced Communications System 1600 Dsl Module User Guide

Avaya, Inc. - x - PARTNER ACS 1600 DSL module User Guide
B. PARTNER ACS 1600 DSL module specifications.....186
C. Connector pinouts......................................................188
D. USI Cables...................................................................190
DTE or DCE?...................................................................... 190
Which Hardware Protocol?................................................. 190
E. IP...

Avaya, Inc. - 11 - PARTNER ACS 1600 DSL module User Guide
1. Introduction
The Avaya PARTNER
 Advanced Communications
System(ACS) 1600 DSL module allows you to simultaneously
transport both voice and data services over a DSL, without the
cost of additional lines.
The PARTNER ACS 1600 DSL module supports a variety of
network transports, including ATM and Frame Relay, as well
as SDSL and phone connections.
Supported Interface standards include:
DSL-SDSL (Symmetrical Digital Subscriber Line) that
supplies...

Avaya, Inc. - 12 - PARTNER ACS 1600 DSL module User Guide
Chapter 6, “Router configuration”, describes how to configure
the PARTNER ACS 1600 DSL module as a router.
Chapter 7, “Bridge configuration”, describes how to configure
the PARTNER ACS 1600 DSL module as a bridge.
Chapter 8, “NAT configuration”, walks you through the steps
required to configure the Network Address Translation (NAT).
Chapter 9, “DHCP server configuration”, walks you through
the steps required to configure the Dynamic Host...

Avaya, Inc. - 13 - PARTNER ACS 1600 DSL module User Guide
2. PARTNER ACS 1600 DSL module
basics
This chapter describes the PARTNER ACS 1600 DSL module
hardware and software requirements, as well as the physical
IAD.
Hardware and
software
requirements
You must use a terminal emulation program, such as
HyperTerminal or ProCommPlus, to configure the PARTNER
ACS 1600 DSL module.  Once you configure an IP address,
you can also use Telnet to remotely administer the PARTNER
ACS 1600 DSL module.  For more...

Avaya, Inc. - 14 - PARTNER ACS 1600 DSL module User Guide
Front View
DSL LineEthernet
LAN
Console
V.35
PARTNER Power LED 

Avaya, Inc. - 15 - PARTNER ACS 1600 DSL module User Guide
3. Getting started
This chapter walks you through the procedures to connect
and log on to the PARTNER ACS 1600 DSL module.  It also
provides information about the Menu interface, restarting the
PARTNER ACS 1600 DSL module, auto log off, exiting the
menu interface and verifying an IP address.
For more information on the menus, submenus and
commands in this chapter, see the “Menu interface” chapter.
Connecting
You can configure the PARTNER ACS 1600...

Avaya, Inc. - 16 - PARTNER ACS 1600 DSL module User Guide
Using a terminal emulation program
To use a terminal emulation program to log on to a PARTNER
ACS 1600 DSL module
1. Open the terminal emulation program.
2. Select the name, icon and COM port for the PARTNER
ACS 1600 DSL module connection.
3. Type or select the following settings, and then save your
changes.
Bits per second:19200
Data bits:8
Parity:None
Stop bits:1
Flow control:None
Emulation:ANSI
Font:Terminal
For more information, see your...

Avaya, Inc. - 17 - PARTNER ACS 1600 DSL module User Guide
8. Configure Login
9. System Utilities
D. Configure DHCP Server
N. Configure NAT
T. Derived Timing
Z. Diagnostics Menu
C. Command Line Interface
P. VoicePath Configure
For more information on the menus, submenus and
commands on the Main Menu, see the “Menu interface”
chapter.
Using a Telnet program
You must set an IP address for the Ethernet port before you
can use a Telnet program to access the PARTNER ACS 1600
DSL module.
Configuring a port IP...

Avaya, Inc. - 18 - PARTNER ACS 1600 DSL module User Guide
2. Select Configure Port IP Address.
The following instructions display on-screen:
Available Interfaces :
1. SDSL
2. 10/100BaseT Ethernet
3. Universal Serial
0. (Abort)
Selection :
Interfaces may or may not display, depending on the IAD
in use.
3. Type the number of the port for which you want to
configure an IP address.
The following message (or one similar) displays:
IP interfaces on port 1:
ID IPAddr
IPMaskPriority
0 255.255.255.0 255.255.255.0...

Avaya, Inc. - 19 - PARTNER ACS 1600 DSL module User Guide
Running the Telnet program
To use a Telnet program to log on to a PARTNER ACS 1600
DSL module
1. Open the Telnet program.
2. Type the IP address of the port that you configured in
steps 1-6, press CONNECT, and then press any key.
The log on message displays.
Enter Login ID >
3. Type your User ID, and press ENTER.
The following are the default User IDs and passwords:
Access Level User ID Password
User User TBD
Network Administrator NetMan TBD
For...