ATT System 25 Administration Manual

To assign a PDC to the1     Follow the procedures stated on page 6-1.
Delay Announcement
2     At 
Action =, enter 2.
machine:
3     At 
Data =, enter the PDC that identifies the delay
announcement machine for DGC usage.
NOTE: After the delay announcement machine is assigned a
port and a PDC, it may be assigned to DGC groups. See
Section 11, “DGC Groups”.
To allow dial access1     Follow the procedures stated on page 6-1.
to the DA:
2     At 
Action =, enter 3.
3     At 
Data =, enter -1 for yes or -O...

Music-on-Hold
To assign Music-on-Hold:1     Follow the procedures stated on page 6-1.
2     At 
Action =, enter 1.
3     At 
Data =, enter 254.
4     Special Hold: A caller is placed on Special Hold when a
multiline set user presses either Transfer or Conference.
You need to indicate whether or not callers will hear music
during the short interval when they are on Special Hold.
You see 
Action = 2 At Data =, enter:
- O if you do not want Music on Special Hold
- 1 if you want Music on Special Hold
VOICE...

To restrict dial access to1     Follow the procedures stated on page 6-1.
all other trunk pools:
2     At 
Action =, enter 4.
3     At 
Data =, enter 1 for yes or 0 for no.
The default is 0.
To restrict this station1     Follow the procedures stated on page 6-1.
from making any
2     At 
Action =, enter 13.
outward calls:
3     At 
Data =, enter 1 for yes or 0 for no.
The default is 0.
To assign a toll1     Follow the procedures stated on page 6-1.
restriction class:
2     At 
Action =, enter 14.
3...

This page intentionally left blank.
6-4b Administering Auxiliary EquipmentNovember 1995 

To make the VMS port an
extended station:NOTE: This option is for TN742 ports only.
1     At 
Action =, enter 10.
2     At 
Data =, enter 1 for yes or 0 for no. The default is 0
To assign or remove a1     At 
Action =, enter 90.
VMS port Display ID:
2     At 
Data =, enter the Display ID (not more than 11
characters, enclosed in double quotes), or enter “ ” to
remove the ID.
Pooled Modem
To assign a Pooled
Modem CP:NOTE: See the procedure for setting pooled modem options
under “Administering System-Wide...

Administering Voice Stations
n     
Assign voice terminals
n     Remove voice terminals
n     Assign and change station dial codes
n     Assign Class of Service
Using the Port and PDC menus: Class-of-Service options for single-line and multiline voice
terminals can be administered from either the PDC menu (Main Menu item 2) or from the Port
menu (Main Menu item 1). This makes it convenient for you to administer a station based on the
information you have. If you know the station PDC, use Menu 2; if you...

TABLE 7-1 Voice Terminal Type Codes
If the Terminal Type is:
Code:
SINGLE-LINE VOICE TERMINALS:
Without message waiting indicator
201
With message waiting indicator202
MERLIN CS (ATL) VOICE TERMINALS:
5-Button, Z7302H01
5-Button Cordless ATL
10-Button, Z7303H01
10-Button Hands-Free Answer on Intercom, Z7309H01
10-Button Built-in-Speakerphone, Z7313H01A
22-Button Built-in-Speakerphone, Z7314H01A
34-Button, Z7305H01
34-Button Deluxe, Z7305H02, (NOT attendant)
34-Button Built-in-Speakerphone, Z7305H03 (NOT...

Display Support
To assign or remove a
PDC Display ID:1     At Action =, enter 90.
2     At 
Data = , enter the Display ID (not more than 11
characters, enclosed in double quotes), or enter “ ” to
remove the ID.
Is this a display voice1     At 
Action =, enter 19. †
terminal?2     At Data =, enter 1 for yes or 0 for no. The default
is 0.
To enable automatic1     At 
Action =, enter 20. †
incoming call
identification messages:2     At 
Data =, enter 1 for yes or 0 for no.
If Action 19 has been set to 1,...

To go on with the action, respond to the system message,
C for continue, any other key for abort . When there are no more
associations with the station you want to remove, you see:
NO MORE BLOCKS
C for continue, any other key for abort
5     Enter C.
You see the following display when the station is
removed:
Action = 1 Data = 0
NOTE: If you remove a station that is associated with other
stations, you may need to reassign features on those other
stations as well.
Changing a Station Dial Code
You can only...

To move a station to a
new port:
1     From the Main Menu prompt, enter 2.
2     At 
PDC =, enter the PDC of the station you want to move.
3     At 
Action =, enter 0.
NOTE: the system displays the station’s present port
assignment at 
Data = CSSPP.
4     Type d, and at Data =, enter the new port assignment
(CSSPP).
Assigning Class of Service
for Single-Line Voice Stations
This section describes the Class-of-Service (COS) options—the calling restrictions and features—
you can administer for single-line...