ATT System 25 Administration Manual

9
10
11
12
Administering Attendant Equipment
Administering Attendant Equipment
Default Attendant Assignments
Assigning a Switched Loop Attendant Console
Assigning a Second Attendant Console
Moving Attendant Consoles
Changing an Attendant PDC
Checking Attendant Position Number
Removing an Attendant Console
Assigning a Direct Extension Selector Console(s) 9-4
Assigning Selector Console Buttons
Display Support
Assigning Class of Service to an
Attendant Console
Assigning Attendant Options (DTAC
and SLAC)...

14
15
16System Searches
System Searches14-1
Administering RS-232 Parameters
Administering RS 232 Parameters15-1
Command Reference
16 Command Reference
Command Reference16-1
16-3
17
18Requirements for the SAT
Requirements for the SAT17-1
Administering the T1 Carrier
Interface (DS1/HI D CKT)
Administering the T1 Carrier Interface (DS1)
TN746 Analog Line Circuit
Administration
High Density Circuit (HI D CKT)
Administration
Port Administration
Timing Administration
18-1
18-1a
18-2
18-6
18-7
IIndex
IndexI-1...

Introduction
This manual provides the information you need to administer AT&T System 25 station,
network access, and system features. This includes configuring the system for initial service
(that is, initializing the system) and making day-to-day changes required for efficient
operation. This manual is for Release 3 systems only. If you have a Release 1, Version 1
system, obtain the Administration Manual numbered 555-500-500. If you have a Release 1,
Version 2 system, obtain the Administration Manual...

The System Administrator is responsible for the following:
n
n
n
n
Training other station users and the Attendant.
After the system has been initialized, assuring that any additions, changes, or deletions to
system or terminal features are made. Your System Administrator may make these
changes or you can contact AT&T to have the technician make the changes.
Maintaining system security.
Notifying company management (and AT&T) about problems, alarms, and service
complaints.
For more information concerning...

How to Use the System
This chapter describes the way you interact with the system using the System Administration
Terminal (SAT). First, it tells you how to log in to System 25. Then, how to use the Main
Menu to access areas of the system you want to administer. Next, it tells you how enter
administration commands to view and change the way your system operates. Finally, it
describes the kinds of warning, error, and text messages the system supplies.
Logging In to System 25
System Security
For security...

Leaving an Administration Session
When you complete an administration session, or if you want to interrupt a session at any
point, just turn off the terminal.
You can also end an administration session by:
n    Unplugging the cable from the modular jack connecting the terminal to the system.
n    Disconnecting the RS232 connector from the terminal.
n    Hanging up to drop the Data Terminal Ready (DTR) signal on disconnect if you are
connected via a modem.
Correcting Typing Errors
You can correct a typing...

The System 25 Administration Main Menu
When you log into the administration terminal, you see the Main Menu. This menu allows you to
enter one of several command areas (Port, PDC, etc.). The Main Menu looks like this (you may
find minor variations on your display):
MAIN MENU
1) PORT7) TOLL ALLOWED LIST
2) PDC8) SEARCH
3) HIDCKT9) SAVE/RESTORE
4) SYSTEM10) RS232
5) FPDC11) ARS
6) DGC12) reserved
Make one selection from menu ->
SCREEN 2-1 Main Menu
When you select an item from the Main Menu, you enter a...

Selecting a Main Menu Item
To select an item from the Main Menu, just type the number of the item you want followed by
[ 
Enter ].
If you type [ 
Enter ] by itself or if you type a number that is not between 1 and 12, the following
message is displayed.
Must be a number from 1-12
Make one selection from menu->
Administration Commands
Once you select an item from the Main Menu, you can administer the features and parameters
accessible in that command area by entering commands. You use commands to tell the...

Command Functions
The previous section introduced you to the basic command formats. This section shows you
how to enter or change an action number, data value, or target value.
Entering Commands
Keep the following considerations about the Return key in mind as you enter commands:
n    As you will see in the section below, to enter information means to type the required
numbers or letters and press [ 
Return ]. The Return key is included in the examples in this
chapter to accustom you to using it....

Here is an example of the D command.
You see:
Port = 10604 Action = 7 Data = 0
>
To change, you enter D 5 [ Return ] and see:
> Data = 5
Port = 10604 Action = 7 Data = 5
>
Changing a Target Value
You can change target values under the following Main Menu items:
n    Port
n    PDC
n    DGC
n    Toll Allowed List
n    RS232.
As examples, the next two sections show you how to change a target value under the Port
and PDC Main Menu items. You change target values under the other command areas in the
same...