ATT System 25 Administration Manual

Removing an Attendant Console
NOTE: If you have two DTACs, you must remove the second console before you remove the
first console. (If you need to check the attendant position number, see the preceding
procedure for Action = 60. SLACs can be removed in any order.
To remove an attendant
console:1     From the Main Menu prompt, enter 1.
2     At 
Port =, enter the CSSPP for the attendant console you
are removing.
3     At 
Action =, enter 1.
4     At 
Data =, enter 0.
You will see a warning message for...

To move the selector
console to a port other
than the default port:1     From the Main Menu prompt, enter 1.
2     At 
Port =, enter the CSSPP for the selector console you
want to move.
3     At 
Action =, enter 1.
4     At 
Data =, enter 0 to remove the current selector
console port assignment.
5     Type t and at 
Port =, enter the new CSSPP for the
selector console.
6     At 
Action =, enter 1.
7     At 
Data =, enter:
1601 for the first selector console.
1602 for the second selector console.
NOTE:...

To assign PDC ranges toNOTE: There are seven possible PDC ranges the attendant can
the selector console groupaccess with group select buttons. 
Action = 21 assigns a PDC
select buttons:hundreds group to the first group select button. 
Action = 22
does the same for the second group select button. You assign
the additional PDC ranges using the numbers 23 through 27 at
Action = .
1     At 
Action =, enter a number, 21-27.
2     At 
Data =, enter the hundreds group followed by two


The defaults are through...

Assigning Class of Service to an Attendant Console
To assign Class of Service1     From the Main Menu prompt, enter 2.
to an attendant console:
2     At 
PDC =, enter the attendant console PDC.
Calling Restrictions
To restrict dial access to
the Central Office (CO)
trunk pool:1     At 
Action =, enter 3.
2     At 
Data =, enter 1 for yes or 0 for no.
The default is 0.
To restrict dial access to
1     At 
Action =, enter 4.
all other trunk pools:
2     At 
Data =, enter 1 for yes or 0 for no.
The default...

To assign an ARS FRL:1     At Action =, enter 15.
2     At 
Data =, enter the FRL number, 0-3, from the following
list:
LevelAllowed FRL Pools
0 -0
1 -
0,1
2 -0,1,2
3 -0,1,2,3
The default is 3.
To assign the account1     At 
Action =, enter 21.
code entry type:
2     At 
Data =, enter:
—0 for optional account code entry
—1 for forced account code entry on all outside calls
—2 for forced account code entry for calls that require
dialing a “0” or “1”
The default is 0.
9-8 Administering Attendant Equipment 

Line Preference
To assign ringing line
preference:1     At 
Action =, enter 5. †
2     At 
Data =, enter 1 for yes or 0 for no.
The default is 1 @.
To assign prime line1     At 
Action =, enter 6.
preference:
2     At 
Data =, enter the button on which this line appears
(the preferred button number), or enter 0 for no line
preference.
The default is 7.
NOTE: For SLACs, prime line preference can only be
assigned to one of the five loop buttons.
Coverage
To specify which receiver1     At 
Action =, enter...

To send ringing to the
coverage station when
this station is busy:1     At Action =, enter 9. ‡
2     At 
Data =, enter 1 for yes or 0 for no.
The default is 1 @.
Pickup: To assign this
1     At 
Action =, enter 11.
station to a pickup group:
2     At 
Data =, enter the pickup group number, 1-16, or 0
for none. The default is 0.
Personal Speed Dialing:
1     At 
Action =, enter 16.
To enable Personal Speed
Dialing at this station:2     At 
Data =, enter 1 for yes or 0 for no.
The default is 0 for...

To assign the number of1     At Action =, enter 42.
times the system will
2     At 
Data =, enter the number of callback retries (after the
retry callback for an
first try) for an outgoing facility, 0 - 15. The default is 2.
outgoing call:
To assign the number of1     At 
Action =, enter 43.
rings per callback try for
2     At 
Data =, enter the maximum number of times the
an outgoing facility:
telephone should ring per callback (2-15). The default is 3.
To enable automatic1     At 
Action =, enter 44....

To delete a trunk from
this station’s Night
Service list:1     At Action =, enter 53.
2     At 
Data =, enter a 4-digit trunk number.
Assigning Attendant Options (DTAC and SLAC)
To assign options to an
attendant console:
To assign the number ofFrom the Main Menu prompt, enter 4.
Assign options to the DTAC or SLAC as described below.
1     At 
Action =, enter 3.
rings before unanswered
calls extended by the2     At 
Data =, enter the number of rings (1-31).
The default is 5.
attendant return to the...

To allow calls to FPDCs
that are not logged in
anywhere to ring at the
attendant console:1     At Action =, enter 5.
2     At 
Data =, enter 1 for yes or 0 for no.
The default is 1 @.
To assign the number of
1     At 
Action =, enter 6.
seconds before a camped-
on call returns to the2     At 
Data =, enter the number of seconds (1-120; 0 means
attendant console:camp-on is not allowed).
The default is 30 @.
To assign PDCs used to
NOTE: 
Action = 11 with a default Data of 800 is the first of 8
park calls...