ATT System 25 Administration Manual

To assign a toll
restriction class:1     At Action =, enter 14.
2     At 
Data =, enter the toll class number, 0 - 5, from the
following list:
O = Not toll restricted
1 = Toll Calls Allowed Lists 1-5
2 = Toll Calls Allowed Lists 2-5
3 = Toll Calls Allowed Lists 3-5
4 = Toll Calls Allowed List 4-5
5 = Toll Calls Allowed List 5 (only)
The default is 0.
NOTE: To allow Toll Restriction station to make operator-
assisted trunk calls, 
Action = 17, Data = 1 must be set for
each trunk used.
To assign an ARS...

To allow toll-restricted
stations to make IXC
codes+1NPA calls:1     At Action =, enter 23.
2At Data =, enter:
- 1 to allow calls
- O to disallow calls
The default is 0.
To allow toll-restricted1     At 
Action =, enter 24.
stations to make IXC
codes+011 calls:
2At Data =, enter:
- 1 to allow calls
- O to disallow calls
The default is 0.
To allow toll-restricted1     At 
Action =, enter 25.
stations to make IXC
codes+NXX calls:
2At Data =, enter:
- 1 to allow calls
- O to disallow calls
The default is...

This page intentionally left blank.
8-6b Administering Data Line and STARLAN CP PortsNovember 1995 

To restrict Third-Party
Call Setup so the user
can only establish calls
for the associated station:
—
—
1     At Action =, enter 22.
2     At 
Data =, enter:
1: to restrict Third-Party Call Setup to just the
associated station specified with Action = 21, or to
totally disable the feature for this terminal (if you
entered Data = 0 for Action = 21).
0: to allow this terminal to call any endpoint station,
or to enable this feature for a STAR-LAN CP.
The default is 1.
Setting Baud Rate and Parity
NOTE: For...

Can this terminal operate
at a baud rate of 1200
bps?
1     At Action =, enter 64 . ‡
2     At 
Data =, enter 1 for yes or 0 for no.
The default is 1.
Can this terminal operate
at a baud rate of 2400
bps?
1     At Action =, enter 65. ‡
2     At 
Data =, enter 1 for yes or 0 for no.
The default is 1.
Can this terminal operate
at a baud rate of 4800
bps?
1     At Action =, enter 66 . ‡
2     At 
Data =, enter 1 for yes or 0 for no.
The default is 0.
Can this terminal operate
at a baud rate of 9600
bps?
1...

To assign the parity
setting to correspond to
the terminal’s parity
setting:NOTE: This setting only specifies the parity the data port will
use when sending text messages to the terminal. All data is
transmitted eight bits per character.
1     At Action =, enter 69. ‡
2     At Data =, enter a number that represents one of the
following parity settings:
0 - zero in the parity bit
1 - one in the parity bit
2 - even parity (may be used for none)
3 - odd parity
The default is 
2.
Assigning Other Data...

To echo dialed characters1     At Action =, enter 73. ‡
during call setup:
2     At 
Data =, enter 1 for yes or 0 for no.
The default is 1.
To set your disconnect1     At 
Action =, enter 74 . ‡
code:
To display call progress
text messages:2     At 
Data =, enter:
—1 for two short BREAKS
—0 for one long BREAK
The default is 1.
1     At 
Action =, enter 75. ‡
2     At 
Data =, enter 1 for yes or 0 for no.
The default is 1.
To display connection1     At 
Action =, enter 77. ‡
indication message:
2     At...

Administering Attendant Equipment
System 25 can have up to two attendant consoles, either Switched Loop Attendant Consoles
(SLACs) or Direct Trunk Attendant Consoles (DTACs). You cannot mix a DTAC and a SLAC
in the same system; both consoles must be the same type.
If you have two attendant consoles, you will sometimes need to distinguish between the first
and second consoles during administration. For administration purposes, the first attendant
console you assign to the system (or the default attendant...

Direct Extension Selector Console System 25 assigns by default a selector console,
associated with the first attendant console, to the second ATL port in the system. Therefore,
if you do not have a selector console, you need to remove the default assignments before you
can reassign the port.
Assigning a Switched Loop Attendant Console
To replace the default
DTAC with a SLAC:1     From the Main Menu prompt, enter 1.
2     At 
Port =, enter the default port assignment for the
attendant console (CSSPP).
3...

4     At Data =, enter:
—309 for a DTAC
—310 for a SLAC
5     You see the prompt, 
Action = 2.
6     At Data =, enter the PDC for the second
attendant console.
Moving Attendant Consoles
To move an attendant1     From the Main Menu prompt, enter 2.
console to a different port
(DTAC or SLAC):2     At 
PDC =, enter the PDC for the attendant you want to
move.
3     At 
Action =, enter 0
4     At 
Data =, enter the new CSSPP for this
attendant console.
Changing an Attendant PDC
To change the attendant1...