ATT 993 Corded 2line Speakerphone Instruction Manual

28
Telephone operation
Feature setup
Set call history                                                                        
You can choose whether or not to store calls in call 
history.
Press ENTER to begin feature setup.
Press  until the screen displays CALLER ID.
Press ENTER. The screen displays AREA CODES.
Press  until the screen displays CALL HISTORY and 
the current setting.
Press  or  to select between All Calls and No Calls.
When the correct setting is shown, press  or ENTER 
to save your...

29
Telephone operation
Feature setup
Turn caller ID with call waiting on or off                              
If you subscribe to combined caller ID with call waiting 
service from your telephone service provider, activate this 
feature in order to see call information for call waiting 
calls.
Press ENTER to begin feature setup.
Press  until the screen displays CALLER ID.
Press ENTER. The screen displays AREA CODES.
Press  until the screen displays CID-CALL WAIT and 
the current setting.
Press  or  to...

30
Telephone operation
Basic operation
Make, answer or end a call                                             
Handset
To make a call, lift the handset and dial the number. The 
number appears on screen when dialing.
To answer a call, lift the handset.
To override automatic line selection, lift the handset, 
then press and release a LINE button.
— OR —
Press the LINE button for the desired line and lift the 
handset.
To end the call, replace the handset.
Speakerphone
To make a call, press SPEAKER. The...

3
Telephone operation
Basic operation
Make, answer or end a call                                             
Headset
Make sure the headset is plugged into the headset 
jack. There will be a low pitch (error) tone if you press 
HEADSET when the headset is not plugged in.
To make a call, press and release HEADSET. The HEADSET 
light goes on. Wait for a dial tone, then dial the call. The 
number appears on screen when dialing.
To answer a call, press HEADSET.
To override automatic line selection,...

32
Telephone operation
Basic operation
Timer                                                                                     
When you are not on a call, the timer starts when you 
make or receive a call on either line. Calls placed on hold 
will not stop the timer. The screen displays the elapsed 
time in minutes and seconds (up to 59:59) and then 
displays the hours and minutes up to  0 hours (09:59) 
before starting at 00:00 again. The timer will not stop 
until all calls have ended.
Volume...

33
Telephone operation
Basic operation
Redial                                                                                      
The last number dialed on this telephone (up to 24 digits) 
is stored in redial memory until another number is dialed.
Handset
To dial the same number again, lift the handset, listen for 
the dial tone, and press (AUTO) REDIAL.
Speakerphone or headset
To dial the same number again, press SPEAKER or 
HEADSET, then press (AUTO) REDIAL. The telephone 
automatically dials the...

34
Telephone operation
Basic operation
Auto redial                                                                             
The telephone can automatically redial the last outgoing 
number up to  0 times, until the other telephone rings or 
you cancel auto redial. It will activate the speakerphone 
to make auto redial calls.
While the telephone is on hook, press (AUTO) REDIAL. 
It dials the number in redial memory using the primary 
line selected or automatic line selection if it is turned 
on....

Telephone operation
35
Options while on calls
Hold                                                                                
While on a call, press HOLD. The LINE light for the call 
will flash slowly while the call is on hold. You can replace 
the handset in the cradle without disconnecting the 
line and the speakerphone or headset is automatically 
disabled.
To release hold and return to the call:
Press the LINE button for the call.
The call will automatically be reconnected in the original...

Telephone operation
36
Options while on calls
Mute                                                                       \
        
Mute allows you to hear the other party, but the other 
party cannot hear you.
To activate this feature, press and release MUTE. The 
MUTE light goes on. 
To return to the conversation, press and release MUTE 
again. 
NOTE: Switching from handset to speakerphone or headset, or from speakerphone or headset to handset, changing lines, and putting acall on hold will cancel...

Telephone operation
37
Options while on calls
Conference calls                                                                   
Talk privately with one caller
Press HOLD.
Press the LINE button of the person with whom you 
wish to speak privately.
Press CONFERENCE to continue the conference call.
To disconnect one party from a conference call and keep 
the other on the line, press the LINE button of the call 
you want to continue.
Low battery indicator...