Apple studio display 17 crt 16 vis adc User Manual

 
Studio Display (17 ADC)  Take Apart -   
9  
 Monitor Stand2. Place the clear plastic ring over the white ring so that the white ring Þts inside the clear 
ring. 
3. Check that the rings are properly aligned. They should easily slide in unison, and 
when they are close to the serial number label, you should be able to see the serial 
number bar code but not be able to clearly see the words Serial Number.
Rings
Correctly Installed 

 
10 -  
Studio Display (17 ADC) Take Apart
 Monitor Stand 
Installing the Replacement Monitor Stand 
1. Holding the new monitor stand, align the slots in the center of the stand with the tabs 
on the base of the monitor.
2. Slide the stand up to engage the locking tabs.
3. Turn the stand counterclockwise.
4. Align the retaining clip and press it down until it clicks into place. The retaining clip is 
keyed and only Þts one way.
5. Check that the stand slides easily.
6. Turn your monitor upright and...

 
Studio Display (17 ADC)  Take Apart -   
11  
 Monitor Stand7.  Restart your computer. 
Warning: Never turn on your monitor unless all of its internal and external parts 
are in place and it is closed. Operating the monitor when it is open or missing 
parts can damage your monitor or cause injury. 
ð 
  
Apple Computer, Inc. 
© 2001 Apple Computer, Inc. All rights reserved.
Under the copyright laws, this document may not be copied, in whole or in part, without the 
written consent of Apple.
The Apple...

 
12 -  
Studio Display (17 ADC) Take Apart
 Remove Rear Housing 
Remove Rear Housing 
Tools 
The following tools are required:
¥ Hex driver, 3/32 inch
¥ Small, plastic, flat-blade screwdriver
¥ #1 Phillips screwdriver
¥ Needlenose pliers
¥ JewelerÕs screwdriver kit 
Preliminary Steps 
Before you begin, remove the monitor stand. 

 
Studio Display (17 ADC)  Take Apart -   
13  
 Remove Rear Housing 
Procedure 
1. Remove six hex screws from the rear housing.  

 
14 -  
Studio Display (17 ADC) Take Apart
 Remove Rear Housing 2. Remove four short hex screws (1) and two longer hex screws (2) from the rear of the 
housing and the stand tilt base.
 
3. Locate  the USB port. Use a small, plastic flat-blade screwdriver or needlenose pliers 
to peel off the USB label. 

 
Studio Display (17 ADC)  Take Apart -   
15  
 Remove Rear Housing 
Replacement Note: 
 Replace the USB label. The USB label should not be re-used 
because the adhesive may not hold the label properly.
4. Remove two screws and the plastic USB hub (1) from the USB port.
 
5. To remove the rear housing, use a  plastic flat-blade screwdriver to push in locking 
tabs at six locations around the bottom of the rear housing.  

 
16 -  
Studio Display (17 ADC) Take Apart
 Remove Rear Housing 6. Lift off the rear housing. 
Replacement Note: 
 When replacing the rear housing, push down Þrmly along each 
side of the housing until you hear it snap securely onto the bezel. 

 
Studio Display (17 ADC)  Take Apart -  
17  
 Remove CRT Shroud 
Remove CRT Shroud 
Tools 
The following tool is required:
¥ #2 Phillips screwdriver 
Preliminary Steps 
Before you begin, remove the following:
¥ Monitor stand
¥ Rear housing 

 
18 -  
Studio Display (17 ADC) Take Apart
 Remove CRT Shroud 
Procedure 
1. Remove two screws from the CRT shroud. 
2. Bow out slightly the bottom of the shroud and remove it from the CRT as shown.