Apple studio display 17 crt 16 vis adc User Manual

							 
© 2003 Apple Computer, Inc. All rights reserved. 
ð 
  
Service Source
 Studio Display (17 CRT, 16
VIS, ADC 
 11 March 2003 
						

							 
© 2002 Apple Computer, Inc. All rights reserved. 
ð 
  
Service Source
Take Apart 
Studio Display (17 CRT, 16 VIS,
ADC) 
						

							 
Studio Display (17 ADC)  Take Apart -   
1  
 General Information 
General Information 
Safety Guidelines 
Warning: 
 This product contains high voltage and a high-vacuum picture tube. To 
prevent serious injury, review CRT safety from the displays product area of 
rollover links on Service Source online. 
Warning: 
 Never use a grounding wriststrap until after discharging the CRT and 
setting up an ongoing ground connection. 
Warning: 
 When the rear housing is removed, avoid the sharp sheet-metal edges of 
the EMI shield, board chassis, and other metal areas of the display assembly. 
						

							 
2 -  
Studio Display (17 ADC) Take Apart
 General Information 
Tools 
The following tools are required:
¥ Soft, clean towel on which to place the display face down
¥ Hex driver, 3/32 inch
¥ #2 Phillips screwdriver
¥ #1 Phillips screwdriver
¥ CRT discharge tool (076-0392)
¥ Small, plastic, flat-blade screwdriver
¥ Needlenose pliers
¥ JewelerÕs screwdriver kit  
Note:  
  To organize the screws your remove from the computer, use a tray with divided 
compartments (such as a plastic ice cube tray). 
Serial Number Location 
The serial number label on the Studio Display (17 CRT, 16 VIS, ADC) may be difÞcult to 
locate. To locate the serial number label:
1. Swivel the monitor so the display is tilted down, and you are facing the side of the 
monitor.
2. Position yourself so you are at eye level with the ADC cable exit point.
3. Locate the serial number label directly in front of the ADC cable exit point.
Serial Number LabelADC Cable
Exit Point 
						

							 
Studio Display (17 ADC)  Take Apart -   
3  
 General Information 
Protecting the Translucent Housing 
Important: 
 Because the housing of this monitor is made of translucent plastic, 
surface scratches can be more visible than on standard plastic housing. To avoid 
cosmetic damage and protect the housing during service procedures, please keep 
in mind the following precautions:
¥ Use a soft towel that is clean and free of debris whenever you service the 
display.
¥ Use caution working with metal tools to avoid scratching the housing.
¥ Before placing the display face on a towel, ensure the surface provides 
protection from scratches. 
						

							 
4 -  
Studio Display (17 ADC) Take Apart
 Monitor Stand 
Monitor Stand  
Note:  
 The monitor stand is a customer-installable part and its replacement is covered by 
the Customer Installable Parts (CIP) program.  The following replacement procedure is 
packed in-the-box with all replacement monitor stands.
Be sure to follow the instructions in this sheet carefully. Failure to follow these instructions 
could result in damage to your equipment and may void your warranty.
Replacing your monitor stand requires Þve basic steps:
¥ Turn off the computer and disconnect the display cable.
¥ Place the monitor upside down on a thick cloth.
¥ Remove the monitor stand.
¥ Install the replacement monitor stand.
¥ Place the monitor upright, connect the display cable, and restart the computer. 
Note: 
 Written and video instructions covering customer-installable parts are available at
http://www.info.apple.com/installparts/. 
Tools 
Two jewelerÕs ßat-blade screwdrivers are required for this procedure. 
Note: 
 If you do not have jewelerÕs screwdrivers, two long carpenterÕs nails can be used. 
However, the head of the nail must be at least 6 mm wide to prevent the nail from sliding 
into the enclosure. 
Warning: If any tools or parts drop into the monitor, do not turn on the monitor. 
Contact Apple for further assistance. Never turn on your monitor unless all of its 
internal and external parts are in place and it is closed. Operating the monitor when 
it is open or missing parts can damage your monitor or cause injury. 
Preliminary Steps 
No preliminary steps are required before you begin this procedure. 
						

							 
Studio Display (17 ADC)  Take Apart -   
5  
 Monitor Stand 
Removing the Monitor Stand 
1. Warning: Turn off your computer and disconnect the display cable as follows: 
¥ Unplug the display cable from the computer.
¥ Wait five minutes for the computerÕs internal components to cool down.
2. 
Warning: 
 The monitor weighs 20 kg (45 pounds). Be careful when repositioning the 
monitor. 
Use a thick, soft, clean cloth (such as a folded blanket or towel) as a cushion. Place 
the monitor upside down on the cloth so the screen is away from you and the monitor 
stand is in front of you.
3. Slide the monitor stand toward the display cable.
Monitor
Stand
Cloth
Display Cable 
						

							 
6 -  
Studio Display (17 ADC) Take Apart
 Monitor Stand 4. In the center of the monitor stand, locate the two identical round openings in the 
retaining clip.
5. Using two jewelerÕs ßat-blade screwdrivers, place one in each of the round openings 
and gently pry up the retaining clip until it is out of the monitor stand. 
Warning: If any tools or parts drop into the monitor, do not turn on the monitor. 
Contact Apple for further assistance. Never turn on your monitor unless all of 
its internal and external parts are in place and it is closed. Operating the 
monitor when it is open or missing parts can damage your monitor or cause 
injury.
Retaining Clip
Round Openings 
						

							 
Studio Display (17 ADC)  Take Apart -   
7  
 Monitor Stand6. Rotate the stand clockwise (1/4 turn) so it is positioned as shown.
7. Peer into the center of the monitor stand and swivel it somewhat until you can see the 
locking tabs line up with the slots in the base.
Locking Tabs 
						

							 
8 -  
Studio Display (17 ADC) Take Apart
 Monitor Stand 8. With the tabs aligned, gently pull the stand toward you. Then tilt the stand up off the 
base. 
Positioning the Plastic Rings 
After you remove the monitor stand, two plastic rings should remain on the base. These 
rings are Þtted in a special orientation so the replacement stand will Þt properly. However, 
if the rings are dislodged, replace them as follows:
1. Place the white plastic ring on the base so that you can still read the words Serial 
Number when the ring is slid all the way down. Turn the ring over if the words are not 
visible
White Ring
Correctly Installed