Apple studio display 17 crt 16 vis adc User Manual
Have a look at the manual Apple studio display 17 crt 16 vis adc User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 195 Apple manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Studio Display (17 ADC) Take Apart - 9 Monitor Stand2. Place the clear plastic ring over the white ring so that the white ring Þts inside the clear ring. 3. Check that the rings are properly aligned. They should easily slide in unison, and when they are close to the serial number label, you should be able to see the serial number bar code but not be able to clearly see the words Serial Number. Rings Correctly Installed
10 - Studio Display (17 ADC) Take Apart Monitor Stand Installing the Replacement Monitor Stand 1. Holding the new monitor stand, align the slots in the center of the stand with the tabs on the base of the monitor. 2. Slide the stand up to engage the locking tabs. 3. Turn the stand counterclockwise. 4. Align the retaining clip and press it down until it clicks into place. The retaining clip is keyed and only Þts one way. 5. Check that the stand slides easily. 6. Turn your monitor upright and reconnect it to the computer. Locking Tabs
Studio Display (17 ADC) Take Apart - 11 Monitor Stand7. Restart your computer. Warning: Never turn on your monitor unless all of its internal and external parts are in place and it is closed. Operating the monitor when it is open or missing parts can damage your monitor or cause injury. ð Apple Computer, Inc. © 2001 Apple Computer, Inc. All rights reserved. Under the copyright laws, this document may not be copied, in whole or in part, without the written consent of Apple. The Apple logo is a trademark of Apple Computer, Inc., registered in the U.S. and other countries. Use of the ÒkeyboardÓ Apple logo (Option-Shift-K) for commercial purposes without the prior written consent of Apple may constitute trademark infringement and unfair competition in violation of federal and state laws. Every effort has been made to ensure that the information in this document is accurate. Apple is not responsible for printing or clerical errors. Apple Computer, Inc. 1 InÞnite Loop Cupertino, CA 95014-2084 408-996-1010 http://www.apple.com Apple and the Apple logo are trademarks of Apple Computer, Inc., registered in the U.S. and other countries.
12 - Studio Display (17 ADC) Take Apart Remove Rear Housing Remove Rear Housing Tools The following tools are required: ¥ Hex driver, 3/32 inch ¥ Small, plastic, flat-blade screwdriver ¥ #1 Phillips screwdriver ¥ Needlenose pliers ¥ JewelerÕs screwdriver kit Preliminary Steps Before you begin, remove the monitor stand.
Studio Display (17 ADC) Take Apart - 13 Remove Rear Housing Procedure 1. Remove six hex screws from the rear housing.
14 - Studio Display (17 ADC) Take Apart Remove Rear Housing 2. Remove four short hex screws (1) and two longer hex screws (2) from the rear of the housing and the stand tilt base. 3. Locate the USB port. Use a small, plastic flat-blade screwdriver or needlenose pliers to peel off the USB label.
Studio Display (17 ADC) Take Apart - 15 Remove Rear Housing Replacement Note: Replace the USB label. The USB label should not be re-used because the adhesive may not hold the label properly. 4. Remove two screws and the plastic USB hub (1) from the USB port. 5. To remove the rear housing, use a plastic flat-blade screwdriver to push in locking tabs at six locations around the bottom of the rear housing.
16 - Studio Display (17 ADC) Take Apart Remove Rear Housing 6. Lift off the rear housing. Replacement Note: When replacing the rear housing, push down Þrmly along each side of the housing until you hear it snap securely onto the bezel.
Studio Display (17 ADC) Take Apart - 17 Remove CRT Shroud Remove CRT Shroud Tools The following tool is required: ¥ #2 Phillips screwdriver Preliminary Steps Before you begin, remove the following: ¥ Monitor stand ¥ Rear housing
18 - Studio Display (17 ADC) Take Apart Remove CRT Shroud Procedure 1. Remove two screws from the CRT shroud. 2. Bow out slightly the bottom of the shroud and remove it from the CRT as shown.