Apple studio display 17 crt 16 vis adc User Manual
Have a look at the manual Apple studio display 17 crt 16 vis adc User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 195 Apple manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Studio Display (17 ADC) Take Apart - 19 Discharge the CRT and Remove Anode Cap Discharge the CRT and Remove Anode Cap Tools The following tools are required: ¥ CRT discharge tool (076-0392) Preliminary Steps Before you begin, remove the following: ¥ Monitor stand ¥ Rear housing ¥ CRT shroud
20 - Studio Display (17 ADC) Take Apart Discharge the CRT and Remove Anode Cap Procedure 1. Attach the grounding clip of the CRT discharge tool to the metal frame of the CRT. 2. Insert the tip of the CRT discharge tool beneath the anode cap and make contact with the edge of the anode (anode aperture).
Studio Display (17 ADC) Take Apart - 21 Discharge the CRT and Remove Anode Cap3. Fold up the anode cap, then squeeze together the metal clip to remove it from the internal edge of the anode aperture. 4. For working inside the monitor with the power off, establish an ongoing ground by using a cable with alligator clips at both ends. Connect one end to the anode aperture, and connect the other end to the metal CRT frame. 5. With the CRT discharged and the ongoing ground in place, wear a grounding wriststrap to prevent equipment damage from static electricity.
22 - Studio Display (17 ADC) Take Apart Discharge the CRT and Remove Anode Cap Replacement Note: When replacing the anode cable, secure it behind the tie wrap as shown in the photo below.
Studio Display (17 ADC) Take Apart - 23 Deflection Board and Mount Assembly Deflection Board and Mount Assembly Tools The following tools are required: ¥ #2 Phillips screwdriver ¥ #1 Phillips screwdriver ¥ Small, plastic, flat-blade screwdriver ¥ Wire cutter ¥ JewelerÕs screwdriver Preliminary Steps Before you begin, remove the following: ¥ Monitor stand ¥ Rear housing ¥ CRT shroud ¥ Discharge the CRT
24 - Studio Display (17 ADC) Take Apart Deflection Board and Mount Assembly Procedure 1. Using a jewelers screwdriver, depress Þve plastic tabs while pulling up on the video can. Separate the video can from the video shield. 2. Use #2 Phillips screwdriver to loosen the neck clamp as shown below.
Studio Display (17 ADC) Take Apart - 25 Deflection Board and Mount Assembly3. Pull the video assembly straight up and off the neck of the CRT. Replacement Note: Visually inspect the pins on the CRT and straighten any that are bent. Carefully align and position the video assembly connector on the neck of the CRT before pressing it down Þrmly. 4. Remove four screws from the stand tilt base.
26 - Studio Display (17 ADC) Take Apart Deflection Board and Mount Assembly 5. Use wire cutters to cut four tie wraps. The three tie wraps on right side of CRT neck are shown below; the fourth tie wrap is on the left side of the CRT neck. 6. Disconnect the degauss cable from deßection board connector B981.
Studio Display (17 ADC) Take Apart - 27 Deflection Board and Mount Assembly7. Disconnect two anode cables from connectors at the rear of the CRT/yoke board. 8. Using a small, plastic ßat-blade screwdriver, release two tabs at the top of the CRT/ yoke board cover and separate the cover from the CRT/yoke board.
28 - Studio Display (17 ADC) Take Apart Deflection Board and Mount Assembly 9. Remove two screws and four ground cables from the the video shield. 10. Tilt back the entire deßection/mount assembly for better access in the following steps. Disconnect the CRT ground cable (1) and the control board cable (2) from connector B101.