Apple studio display 17 crt 16 vis adc User Manual

Studio Display (17 ADC)  Take Apart - 39
 CRT
 CRT
Tools
The following tools are required:
¥ #2 Phillips screwdriver
¥ #1 Phillips screwdriver
Preliminary Steps
Before you begin, remove the following:
¥ Monitor stand
¥ Rear housing
¥ CRT shroud
¥ Discharge the CRT
¥ Deflection board and mount assembly
¥ Deflection board assembly
¥ Video cable 

40 - Studio Display (17 ADC) Take Apart
 CRT
Procedure
1. Remove four screws (1) from the metal degauss frame. Remove four more (black) 
screws (2) from bezel mount and degauss frame. 
2. Lift slightly the bottom side of the degauss frame and disconnect the power button 
cable and the launch button cable. Remove the CRT from the front bezel assembly. 

Studio Display (17 ADC)  Take Apart - 41
 Front Bezel
Front Bezel
Tools
The following tools are required:
¥ #1 Phillips screwdriver
Preliminary Steps
Before you begin, remove the following:
¥ Monitor stand
¥ Rear housing
¥ CRT shroud
¥ Discharge the CRT
¥ Deflection board and mount assembly
¥ Deflection board assembly
¥ Video cable
¥ CRT 

42 - Studio Display (17 ADC) Take Apart
 Front Bezel
Procedure
1. Use a small, plastic ßat-blade screwdriver to disengage four plastic mounting tabs, 
and pull up to separate the bezel mount from the front bezel. 
2. Remove two screws and the power button board (1) from the front bezel. 
  

Studio Display (17 ADC)  Take Apart - 43
 Front Bezel3. Remove two screws and the launch button board (2) from the bezel. 
4. Remove the power button (1) and the launch button (2) from the front bezel.  

 
© 2002 Apple Computer, Inc. All rights reserved. 
ð 
  
Service Source
Adjustments 
Studio Display (17 CRT, 16 VIS,
ADC) 

ContentsIntroduction-----------------2Hardware Requirements-----------------2Hardware Setup-----------------2CA100 Equipment Setup-----------------3Software Requirements-----------------3Alignment Condition Requirements-----------------3Alignment Procedures-----------------4Turning ON the unit -----------------4Data Upload -----------------4Data Download -----------------4B+ voltage check and adjustment -----------------4USB output voltage check -----------------51V check and adjustment...

2IntroductionThis is the read-me file for the documentation of the Mac-based Cabernet rework(version 1.1) software. This documentation should be used in conjunction with the ADICabernet service manual. Refer to the appendix A for descriptions on the availablesoftware features and functions in this rework software.Hardware Requirements1. Power PC with PCI slot and serial ports.2. ADS USB card.3. Quantum 801GF with Mac serial cable connected to serial printer port.4. Minolta CA100 with Mac serial cable...

3CA100 Equipment Setup1. Check that the CA100 has been set to FL.2. Check that the baud rate has been set to 2400.3. Connect the DB25 connector of the serial cable to the CA100 RS232 terminal and theDIN 8 to the Mac serial modem port.4. The Minolta color analyzer CA100 must be calibrated with a high accuracycolorimeter (e.g. LMT) or photometer for the following color temperature in thememory channels:· Channel 1 = 4100.· Channel 2 = 5000.· Channel 3 = 6500.· Channel 5 = 9300.· Channel 6 = Red.· Channel 7...

4Alignment ProceduresTurning ON the unit1. Click on “Preset & read” to ensure that the Cabernet can be found on the USB.Message should show “UUT found”, if not check the connection. Also ensure that thecheck box “Preset Contrast” is ticked.2. Click on the button “UUT ON” to power ON the UUT.  Important note: Must clickon the button “UUT OFF” to power OFF the UUT after adjustment. Failure to click“UUT OFF” will result in higher power consumption in sleep mode and abnormalpower ON operation (i.e. degauss...