Apple macbook pro 15 inch mid 2010 User Manual
Have a look at the manual Apple macbook pro 15 inch mid 2010 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 195 Apple manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
MacBook Pro (15-inch, Mid 2010) Take Apart — Trackpad 181 2010-12-15 6 Turn top case over. Tighten screws at flexures. 7 Check that gaps between trackpad and top case are even on all sides. If not, loosen screws and adjust. 8 Replace 1 T6 set screw. 9 Slowly turn set screw in small increments until trackpad has a normal clicking motion. Important: Do not overtighten set screw or you may damage trackpad. 10 Press trackpad flex cable into place on top case.
MacBook Pro (15-inch, Mid 2010) Take Apart — Left Speaker 182 2010-12-15 First Steps Remove: • Bottom case • Battery • AirPort/Bluetooth flex cable • Right fan • Logic board Tools • Clean, soft, lint-free cloth • ESD wrist strap and mat • Magnetic Phillips #00 screwdriver Left Speaker
MacBook Pro (15-inch, Mid 2010) Take Apart — Left Speaker 183 2010-12-15 Removal 1 Carefully peel back tape and disconnect speaker cable from logic board. Replacement Note: Be sure to replace the tape covering the speaker cable. If you cannot reuse the original tape, use a piece of Kapton tape. 2 Remove 2 (4.5 mm) 922-8744 screws. Note: Do not touch the soft speaker cone. 3 Disconnect microphone cable from logic board. 4 Remove speaker and microphone from top case. Replacement Note: If you are replacing the speaker, transfer microphone to replacement speaker before installing new speaker.
MacBook Pro (15-inch, Mid 2010) Take Apart — Microphone 184 2010-12-15 First Steps Remove: • Bottom case • Battery • AirPort/Bluetooth flex cable • Right fan • Logic board • Left speaker Tools • Clean, soft, lint-free cloth • ESD wrist strap and mat • Black stick Microphone
MacBook Pro (15-inch, Mid 2010) Take Apart — Microphone 185 2010-12-15 Removal Use black stick to pry microphone cable from speaker assembly.
MacBook Pro (15-inch, Mid 2010) Take Apart — MagSafe Board 186 2010-12-15 First Steps Remove: • Bottom case • Battery • AirPort/Bluetooth flex cable • Right fan • Logic board Tools • Clean, soft, lint-free cloth • ESD wrist strap and mat • Magnetized Torx T6 screwdriver MagSafe Board
MacBook Pro (15-inch, Mid 2010) Take Apart — MagSafe Board 187 2010-12-15 Removal 1 Remove 2 (7.5 mm) 922-9042 Torx T6 screws. 2 Remove MagSafe board from case. Replacement Note: After installing the MagSafe screws, check the port connection by plugging in a disconnected power adapter cable. If the MagSafe port is off center, the cable will not plug in securely, and you must reinstall the MagSafe board.
MacBook Pro (15-inch, Mid 2010) Take Apart — Battery Indicator Light Cable and Board 188 2010-12-15 First Steps Remove: • Bottom case • Battery • AirPort/Bluetooth flex cable • Right fan • Logic board Tools • Clean, soft, lint-free cloth • ESD wrist strap and mat • Magnetized Phillips #000 screwdriver • Black stick Battery Indicator Light Cable and Board
MacBook Pro (15-inch, Mid 2010) Take Apart — Battery Indicator Light Cable and Board 189 2010-12-15 Removal 1 Place tape over battery button on outside of top case to prevent losing the button. 2 Remove 3 (1.8 mm) 922-9069 screws. 3 Using a black stick, pry back the EMI spring shield to access the BIL cable. Note: If replacing the BIL board, discard the bent EMI spring shield. Install new shield that came with BIL assembly. 4 Peel the cable off the top housing. Replacement Note: Before replacing the BIL board, check that: • the long rubber gasket is assembled on top of the LEDs • the BIL button is installed in the top case • the EMI spring shield is installed
MacBook Pro (15-inch, Mid 2010) Take Apart — Center Bracket 190 2010-12-15 First Steps Do the following: • Remove bottom case • Remove battery • Remove AirPort/ Bluetooth flex cable • Rotate AirPort/ Bluetooth card holder back from bottom case • Remove optical drive • Remove right fan • Remove logic board Tools • Clean, soft, lint-free cloth • ESD wrist strap and mat • Magnetized Phillips #00 screwdriver Center Bracket