Apple macbook pro 15 inch mid 2009 User Manual
Have a look at the manual Apple macbook pro 15 inch mid 2009 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 195 Apple manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
MacBook Pro (15-inch, Mid 2009) Take Apart — Memory 141 2010-12-15 First Steps Remove: • Bottom case • Battery Caution: Avoid touching anything other than the memory area. Tools • Clean, soft, lint-free cloth • ESD wrist strap and mat Memory
MacBook Pro (15-inch, Mid 2009) Take Apart — Memory 142 2010-12-15 Memory Information Memory cards must be: • 1.18 inch (30 mm) • 2 GB or 4 GB • 204-pin • PC-8500 DDR3, 1066 MHz RAM Removal 1 Push 2 ejection levers outward until the memory pops up at an angle. Make sure you see the half-circle notches on the memory card. If not, press the ejection levers again. 2 Remove memory card from the slot. 3 Hold the card by the edges. 4 Do not touch the gold connectors. This computer comes with a minimum of 4 GB of 1066 GHz Double Data Rate (DDR3) Synchronous Dynamic Random-Access Memory (SDRAM) installed. Both memory slots can accept an SDRAM module that meets the specifications listed. The slots are stacked on the logic board under the bottom case. For best performance, memory should be installed as pairs with an equal memory card in each slot. The maximum amount of memory for this computer is 8 GB, with a 4 GB DIMM installed in each slot.
MacBook Pro (15-inch, Mid 2009) Take Apart — Memory 143 2010-12-15 Replacement 1 Install cards at an angle. If installing just one card, install it in lower slot. 2 Press card down. You will hear a click when inserted correctly. 3 If you installed additional memory, check that the computer recognizes it.
MacBook Pro (15-inch, Mid 2009) Take Apart — Bluetooth Card With Holder 144 2010-12-15 First Steps Remove: • Bottom case • Battery Note: This procedure applies only to anti-glare display models Tools • Clean, soft, lint-free cloth • ESD wrist strap and mat • Magnetized Phillips #00 screwdriver • Black stick Bluetooth Card With Holder Note: This procedure applies only to anti-glare display models.
MacBook Pro (15-inch, Mid 2009) Take Apart — Bluetooth Card With Holder 145 2010-12-15 Removal 1 Disconnect 2 screws. 2 Peel up mylar cover, and disconnect 2 cables: 3 Using black stick, pry camera cable off Bluetooth card holder. 4 Slide Bluetooth holder and card from underneath camera cable and remove assembly from computer.
MacBook Pro (15-inch, Mid 2009) Take Apart — Bluetooth Card With Holder 146 2010-12-15 Replacement Note: Install Bluetooth holder on optical drive as illustrated. Check that • holder slides under camera cable • holder’s clamp secures camera cable • screw holes align • grommets are positioned on top of holder’s screw holes
MacBook Pro (15-inch, Mid 2009) Take Apart — Camera Cable Guide 147 2010-12-15 First Steps Remove: • Bottom case • Battery Tools • Clean, soft, lint-free cloth • ESD wrist strap and mat • Magnetized Phillips #00 screwdriver Camera Cable Guide Note: This procedure does not apply to anti-glare models with the Bluetooth card option. The camera cable guide on these models is built into the Bluetooth card holder.
MacBook Pro (15-inch, Mid 2009) Take Apart — Camera Cable Guide 148 2010-12-15 Removal 1 Remove 2 (8-mm) screws (922-9107). 2 Remove cable guide from the top case. Replacement Note: Be sure to anchor the ground tab when reinstalling the screw closest to the display clutch cover.
MacBook Pro (15-inch, Mid 2009) Take Apart — LVDS Cable Guide 149 2010-12-15 First Steps Remove: • Bottom case • Battery Tools • Clean, soft, lint-free cloth • ESD wrist strap and mat • Magnetized Phillips #00 screwdriver LVDS Cable Guide
MacBook Pro (15-inch, Mid 2009) Take Apart — LVDS Cable Guide 150 2010-12-15 Removal 1 Remove 1 (7-mm) screw (922-8645). Replacement Note: Be sure to anchor the ground tab when reinstalling the screw.