Apple macbook 13 inch aluminum late 2008 User Manual
Have a look at the manual Apple macbook 13 inch aluminum late 2008 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 195 Apple manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
MacBook (13-inch, Aluminum, Late 2008) Take Apart — Memory 131 2010-06-15 Removal Memory cards must be: • 1.25 inch or smaller • 1 GB or 2 GB • 204-pin • PC-8500 DDR3, 1066 MHz RAM 1 Press out 2 ejection levers until the card pops up completely, The card pops up at an angle. Before removing the card, make sure you see the half- circle notches. If not, press the ejection levers again. 2 Pull out the card. 3 Hold the card by the edges. 4 Do not touch the gold connectors. This computer comes with a minimum of 2 GB of 1066 MHz Double Data Rate 3 (DDR3) Synchronous Dynamic Random-Access Memory (SDRAM) installed. It has two slots that can accept SDRAM Small Outline Dual Inline Memory Modules (SO-DIMMs). The slots are stacked on the logic board under the bottom case. For best performance, memory should be installed as pairs with an equal memory card in each slot. The maximum amount of memory for this computer is 4 GB, with a 2 GB DIMM installed in each slot.
MacBook (13-inch, Aluminum, Late 2008) Take Apart — Memory 132 2010-06-15 Replacement 1 Install cards at an angle. If installing just one card, install it in lower slot. 2 Spread ejection levers, and press card down. Note: New memory cards might have a harmless white residue on the gold connectors. 3 If you installed additional memory, check that computer recognizes it.
MacBook (13-inch, Aluminum, Late 2008) Take Apart — Mid Wall 133 2010-06-15 First Steps Remove: • Access door • Battery • Bottom case Tools • Clean, soft, lint-free cloth • ESD wrist strap and mat • Magnetized Phillips #00 screwdriver Caution: The screws for this procedure require a newer screwdriver. Using a dull screwdriver can damage the screw heads. Mid Wall
MacBook (13-inch, Aluminum, Late 2008) Take Apart — Mid Wall 134 2010-06-15 Removal To prevent scratches to the computer housing, use a soft cloth when removing and installing screws. 1 Remove 4 (10.5-mm) 922-8656 screws in order shown. Replacement Note: Install screws in order shown. 2 Lift out mid wall.
MacBook (13-inch, Aluminum, Late 2008) Take Apart — Battery Connector Cover 135 2010-06-15 First Steps Remove: • Access door • Battery • Bottom case • Mid wall To prevent scratches to the computer housing, use a soft cloth when removing and installing screws. Tools • Clean, soft, lint-free cloth • ESD wrist strap and mat • Magnetized Phillips #00 screwdriver • Black stick Battery Connector Cover
MacBook (13-inch, Aluminum, Late 2008) Take Apart — Battery Connector Cover 136 2010-06-15 Removal 1 Remove 3 screws: • 1 (2.5 mm) 922-8652 • 2 (1.5 mm) 922-8651 Replacement Note: Install screws in order shown. 2 Lift out battery connector cover.
MacBook (13-inch, Aluminum, Late 2008) Take Apart — Battery Cable Guide 137 2010-06-15 First Steps Remove: • Access door • Battery • Bottom case • Mid wall • Battery connector cover To prevent scratches to the computer housing, use a soft cloth when removing and installing screws. Tools • Clean, soft, lint-free cloth • ESD wrist strap and mat • Magnetized Phillips #00 screwdriver Battery Cable Guide
MacBook (13-inch, Aluminum, Late 2008) Take Apart — Battery Cable Guide 138 2010-06-15 Removal 1 Remove 2.7-mm (922-8661) screw. 2 Lift out battery cable guide.
MacBook (13-inch, Aluminum, Late 2008) Take Apart — Battery Power Cable 139 2010-06-15 First Steps Remove: • Access door • Battery • Bottom case • Mid wall • Battery connector cover • Battery cable guide Tools • Clean, soft, lint-free cloth • ESD wrist strap and mat Battery Power Cable
MacBook (13-inch, Aluminum, Late 2008) Take Apart — Battery Power Cable 140 2010-06-15 Removal 1 Disconnect the battery cable, and peel it up from the top case. 2 Route the cable through the top case slot. Replacement 1 Connect cable to logic board. 2 Press cable to top case so it lays flat.