Apple macbook 13 inch aluminum late 2008 User Manual
Here you can view all the pages of manual Apple macbook 13 inch aluminum late 2008 User Manual. The Apple manuals for Notebook are available online for free. You can easily download all the documents as PDF.
Page 131
MacBook (13-inch, Aluminum, Late 2008) Take Apart — Memory 131 2010-06-15 Removal Memory cards must be: • 1.25 inch or smaller • 1 GB or 2 GB • 204-pin • PC-8500 DDR3, 1066 MHz RAM 1 Press out 2 ejection levers until the card pops up completely, The card pops up at an angle. Before removing the card, make sure you see the half- circle notches. If not, press the ejection levers again. 2 Pull out the card. 3 Hold the card by the edges. 4 Do not touch the gold connectors. This computer comes...
Page 132
MacBook (13-inch, Aluminum, Late 2008) Take Apart — Memory 132 2010-06-15 Replacement 1 Install cards at an angle. If installing just one card, install it in lower slot. 2 Spread ejection levers, and press card down. Note: New memory cards might have a harmless white residue on the gold connectors. 3 If you installed additional memory, check that computer recognizes it.
Page 133
MacBook (13-inch, Aluminum, Late 2008) Take Apart — Mid Wall 133 2010-06-15 First Steps Remove: • Access door • Battery • Bottom case Tools • Clean, soft, lint-free cloth • ESD wrist strap and mat • Magnetized Phillips #00 screwdriver Caution: The screws for this procedure require a newer screwdriver. Using a dull screwdriver can damage the screw heads. Mid Wall
Page 134
MacBook (13-inch, Aluminum, Late 2008) Take Apart — Mid Wall 134 2010-06-15 Removal To prevent scratches to the computer housing, use a soft cloth when removing and installing screws. 1 Remove 4 (10.5-mm) 922-8656 screws in order shown. Replacement Note: Install screws in order shown. 2 Lift out mid wall.
Page 135
MacBook (13-inch, Aluminum, Late 2008) Take Apart — Battery Connector Cover 135 2010-06-15 First Steps Remove: • Access door • Battery • Bottom case • Mid wall To prevent scratches to the computer housing, use a soft cloth when removing and installing screws. Tools • Clean, soft, lint-free cloth • ESD wrist strap and mat • Magnetized Phillips #00 screwdriver • Black stick Battery Connector Cover
Page 136
MacBook (13-inch, Aluminum, Late 2008) Take Apart — Battery Connector Cover 136 2010-06-15 Removal 1 Remove 3 screws: • 1 (2.5 mm) 922-8652 • 2 (1.5 mm) 922-8651 Replacement Note: Install screws in order shown. 2 Lift out battery connector cover.
Page 137
MacBook (13-inch, Aluminum, Late 2008) Take Apart — Battery Cable Guide 137 2010-06-15 First Steps Remove: • Access door • Battery • Bottom case • Mid wall • Battery connector cover To prevent scratches to the computer housing, use a soft cloth when removing and installing screws. Tools • Clean, soft, lint-free cloth • ESD wrist strap and mat • Magnetized Phillips #00 screwdriver Battery Cable Guide
Page 138
MacBook (13-inch, Aluminum, Late 2008) Take Apart — Battery Cable Guide 138 2010-06-15 Removal 1 Remove 2.7-mm (922-8661) screw. 2 Lift out battery cable guide.
Page 139
MacBook (13-inch, Aluminum, Late 2008) Take Apart — Battery Power Cable 139 2010-06-15 First Steps Remove: • Access door • Battery • Bottom case • Mid wall • Battery connector cover • Battery cable guide Tools • Clean, soft, lint-free cloth • ESD wrist strap and mat Battery Power Cable
Page 140
MacBook (13-inch, Aluminum, Late 2008) Take Apart — Battery Power Cable 140 2010-06-15 Removal 1 Disconnect the battery cable, and peel it up from the top case. 2 Route the cable through the top case slot. Replacement 1 Connect cable to logic board. 2 Press cable to top case so it lays flat.