Apple macbook 13 inch aluminum late 2008 User Manual
Here you can view all the pages of manual Apple macbook 13 inch aluminum late 2008 User Manual. The Apple manuals for Notebook are available online for free. You can easily download all the documents as PDF.
Page 141
MacBook (13-inch, Aluminum, Late 2008) Take Apart — Battery Indicator Light (BIL) Cable 141 2010-06-15 First Steps Remove: • Access door • Battery • Bottom case • Mid wall • Battery connector cover Tools • Clean, soft, lint-free cloth • ESD wrist strap and mat • Magnetized Phillips #00 screwdriver • Permanent marking felt-tip pen Battery Indicator Light (BIL) Cable
Page 142
MacBook (13-inch, Aluminum, Late 2008) Take Apart — Battery Indicator Light (BIL) Cable 142 2010-06-15 Removal 1 Draw line on inner edge of cable. to mark cable routing. 2 Remove 2.7 mm (922-8661) screw. 3 Disconnect cable from logic board. 4 Remove battery cable guide. 5 Route cable through top case wall.
Page 143
MacBook (13-inch, Aluminum, Late 2008) Take Apart — Battery Indicator Light (BIL) Cable 143 2010-06-15 6 Remove 3 (3-mm) 922-8657 screws. 7 Lift up BIL board from side of top case. 8 Disconnect cable from BIL board. Note: With board removed, BIL button might pop out. Make sure you retain the BIL button.
Page 144
MacBook (13-inch, Aluminum, Late 2008) Take Apart — Battery Indicator Light (BIL) Cable 144 2010-06-15 Replacement 1 Make sure rubber gasket is installed on inner side of BIL board. 2 Set and hold button in top case wall. Then install cable and BIL board. 3 Press cable so it lays completely flat.
Page 145
MacBook (13-inch, Aluminum, Late 2008) Take Apart — Camera Cable Guide 145 2010-06-15 First Steps Remove: • Access door • Battery • Bottom case Tools • Clean, soft, lint-free cloth • ESD wrist strap and mat • Magnetized Phillips #00 screwdriver • Black stick Camera Cable Guide
Page 146
MacBook (13-inch, Aluminum, Late 2008) Take Apart — Camera Cable Guide 146 2010-06-15 Removal 1 Remove 3 screws: • 1 (4-mm) 922-8650 • 2 (8-mm) 922-8665 Replacement Note: Install screws in order shown. 2 Use a black stick to tilt out the camera cable guide. Replacement 1 Important: Insert the cable guide under the speaker and install the 4-mm screw (922- 8650). 2 Make sure the ground tab is over the cable guide before installing the 2 remaining screws.
Page 147
MacBook (13-inch, Aluminum, Late 2008) Take Apart — LVDS Cable Guide 147 2010-06-15 First Steps Remove: • Access door • Battery • Bottom case Tools • Clean, soft, lint-free cloth • ESD wrist strap and mat • Magnetized Phillips #00 screwdriver LVDS Cable Guide
Page 148
MacBook (13-inch, Aluminum, Late 2008) Take Apart — LVDS Cable Guide 148 2010-06-15 Removal 1 Remove 2 screws: • 5-mm in corner (922- 8658) • 7-mm (922-8645) 2 Lift out cable guide. Replacement Note: Align locator pin to hole in top case.
Page 149
MacBook (13-inch, Aluminum, Late 2008) Take Apart — Display Assembly 149 2010-06-15 First Steps Remove: • Access door • Battery • Bottom case • Camera cable guide • LVDS cable guide Tools • Clean, soft, lint-free cloth • ESD wrist strap and mat • Magnetized Phillips #00 screwdriver • Torx T6 screwdriver • Foam wedge fixture Display Assembly
Page 150
MacBook (13-inch, Aluminum, Late 2008) Take Apart — Display Assembly 150 2010-06-15 Removal 1. Close display and place on soft cloth. 2. In the direction shown, peel off foam gasket from the LVDS connector. Caution: Refer to Connector Types before disconnecting cables. 3. Disconnect and unroute 3 cables: • subwoofer • camera • LVDS 4. Remove 4-mm screw (922-8644) from the subwoofer.