Apple IPhone 6 Manual
Have a look at the manual Apple IPhone 6 Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 195 Apple manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Chapter 3 Basics 41 Restrictions You can set restrictions for some apps, and for purchased content. For example, parents can restrict explicit music from appearing in playlists, or disallow changes to certain settings. Use restrictions to prevent the use of certain apps, the installation of new apps, or changes to accounts or the volume limit. Turn on restrictions. Go to Settings > General > Restrictions, then tap Enable Restrictions. You’ll be asked to define a restrictions passcode that’s necessary in order to change the settings you make. This can be different than the passcode for unlocking iPhone. Important: If you forget your restrictions passcode, you must restore the iPhone software. See Restore iPhone on page 17 8 . Privacy Privacy settings let you see and control which apps and system services have access to Location Services, and to contacts, calendars, reminders, and photos. Location Services lets location-based apps such as Reminders, Maps, and Camera gather and use data indicating your location. Your approximate location is determined using available information from cellular network data, local Wi-Fi networks (if you have Wi-Fi turned on), and GPS (may not be available in all areas). The location data collected by Apple isn’t collected in a form that personally identifies you. When an app is using Location Services, appears in the status bar. Turn Location Services on or off. Go to Settings > Privacy > Location Services. You can turn it off for some or for all apps and services. If you turn off Location Services, you’re prompted to turn it on again the next time an app or service tries to use it. Turn Location Services off for system services. Several system services, such as compass calibration and location-based ads, use Location Services. To see their status, turn them on or off, or show in the status bar when these services use your location, go to Settings > Privacy > Location Services > System Services. Turn off access to private information. Go to Settings > Privacy. You can see which apps and features have requested and been granted access to the following information: •Contacts •Calendar •Reminders •Photos •Bluetooth Sharing •Microphone •Camera •HomeKit •Health •Motion Activity •Twitter •Facebook You can turn off each app’s access to each category of information. Review the terms and privacy policy for each third-party app to understand how it uses the data it’s requesting. For more information, see support.apple.com/kb/HT6338.
Chapter 3 Basics 42 Security Security features help protect the information on iPhone from being accessed by others. Use a passcode with data protection For better security, you can set a passcode that must be entered each time you turn on or wake up iPhone. Set a passcode. Go to Settings > Touch ID & Passcode (iPhone models with Touch ID) or Settings > Passcode (other models), then set a 4-digit passcode. Setting a passcode turns on data protection, using your passcode as a key to encrypt Mail messages and attachments stored on iPhone, using 256-bit AES encryption. (Other apps may also use data protection.) Increase security. Turn off Simple Passcode and use a longer passcode. To enter a passcode that’s a combination of numbers and letters, you use the keyboard. If you prefer to unlock iPhone using the numeric keypad, create a passcode using numbers only. Add fingerprints and set options for the Touch ID sensor. (iPhone models with Touch ID) Go to Settings > Touch ID & Passcode. See Touch ID, below. Allow access to features when iPhone is locked. Go to Settings > Touch ID & Passcode (iPhone models with Touch ID) or Settings > Passcode (other models). Optional features include: •To d a y •Notifications View •Siri (if enabled, see Siri settings on page 47 ) •Passbook (see Chapter 26, Passbook, on page 12 3 ) •Reply with Message (see When someone calls on page 49) Allow access to Control Center when iPhone is locked. Go to Settings > Control Center. See Control Center on page 33 . Erase data after ten failed passcode attempts. Go to Settings > Touch ID & Passcode (iPhone models with Touch ID) or Settings > Passcode (other models), then tap Erase Data. After ten failed passcode attempts, all settings are reset, and all your information and media are erased by removing the encryption key to the data. If you forget your passcode, you must restore the iPhone software. See Restore iPhone on page 17 8 . Touch ID On iPhone models with Touch ID, you can use a fingerprint instead of: •Entering your passcode to unlock iPhone •Using your Apple ID password to make purchases in the iTunes Store, App Store, or iBooks Store •Presenting your credit card or debit card when making a purchase in a store that offers Apple Pay as a method of payment •Providing debit and credit card info, billing and shipping addresses, and contact info when paying in an app that offers Apple Pay as a method of payment Set up the Touch ID sensor. Go to Settings > Touch ID & Passcode. Set whether you want to use a fingerprint to unlock iPhone, and to make purchases. Tap Add a Fingerprint, then follow the onscreen instructions. You can add more than one fingerprint (your thumb and forefinger, for example, or one for your spouse).
Chapter 3 Basics 43 Note: If you turn iPhone off after setting up the Touch ID sensor, you’ll be asked to confirm your passcode when you turn iPhone back on and unlock it the first time. You’ll also be asked for your Apple ID password for the first purchase you make in the iTunes Store, App Store, or iBooks Store. Delete a fingerprint. Tap the fingerprint, then tap Delete Fingerprint. If you have more than one fingerprint, touch the Home button to find out which fingerprint it is. Name a fingerprint. Tap the fingerprint, then enter a name, such as “Thumb.” Use the Touch ID sensor to unlock iPhone. Touch the Home button with a finger you’ve added in Settings. You can unlock iPhone from either the Lock screen or the Passcode screen. Use the Touch ID sensor to make a payment in the iTunes Store, App Store, or iBooks Store. When purchasing from the iTunes Store, App Store, or iBooks Store, follow the prompts to enable purchases with your fingerprint. Or go to Settings > Touch ID & Passcode, then turn on iTunes & App Store. Use Touch ID for Apple Pay. (iPhone 6 or iPhone 6 Plus) Go to Settings > Touch ID & Passcode to ensure that Apple Pay is enabled with your Touch ID. For more information see Apple Pay on page 12 4 . iCloud Keychain iCloud Keychain keeps your Safari website user names and passwords, credit card information, and Wi-Fi network information up to date. iCloud Keychain works on all your approved devices (iOS 7 or later) and Mac computers (OS X Mavericks or later). iCloud Keychain works with Safari Password Generator and AutoFill. When you’re setting up a new account, Safari Password Generator suggests unique, hard-to-guess passwords. You can use AutoFill to have iPhone enter your user name and password info, making login easy. See Fill in forms on page 63. Note: Some websites do not support AutoFill. iCloud Keychain is secured with 256-bit AES encryption during storage and transmission, and cannot be read by Apple. Set up iCloud Keychain. Go to Settings > iCloud > Keychain. Turn on iCloud Keychain, then follow the onscreen instructions. If you’ve set up iCloud Keychain on other devices, you need to approve use of iCloud Keychain from one of those devices, or use your iCloud Security Code. Important: If you forget your iCloud Security Code, you’ll have to start over and set up your iCloud Keychain again. Set up AutoFill. Go to Settings > Safari > Passwords & AutoFill. Make sure Names and Passwords, and Credit Cards, are turned on (they’re on by default). To add credit card info, tap Saved Credit Cards. The security code for your credit card is not saved—you have to enter that manually. To automatically fill in names, passwords, or credit card info on sites that support it, tap a text field, then tap AutoFill. To protect your personal information, set a passcode if you turn on iCloud Keychain and AutoFill. Limit Ad Tracking Restrict or reset Ad Tracking. Go to Settings > Privacy > Advertising. Turn on Limit Ad Tracking to prevent apps from accessing your iPhone advertising identifier. For more information, tap About Advertising & Privacy.
Chapter 3 Basics 44 Find My iPhone Find My iPhone can help you locate and secure your iPhone using the free Find My iPhone app (available in the App Store) on another iPhone, iPad, or iPod touch, or using a Mac or PC web browser signed into www.icloud.com/find. Find My iPhone includes Activation Lock, which is designed to prevent anyone else from using your iPhone if you ever lose it. Your Apple ID and password are required to turn off Find My iPhone or to erase and reactivate your iPhone. Turn on Find My iPhone. Go to Settings > iCloud > Find My iPhone. Important: To use Find My iPhone features, Find My iPhone must be turned on before your iPhone is lost. iPhone must be able to connect to the Internet for you to locate and secure the device. Use Find My iPhone. Open the Find My iPhone app on an iOS device, or go to www.icloud.com/find on your computer. Sign in and select your device. •Play Sound: Play a sound at full volume for two minutes, even if the ringer is set to silent. •Lost Mode: Immediately lock your missing iPhone with a passcode and send it a message displaying a contact number. iPhone tracks and reports its location, so you can see where it’s been when you check the Find My iPhone app. Lost Mode also suspends the use of your credit and debit cards used for Apple Pay (iPhone 6 and iPhone 6 Plus). See Apple Pay on page 12 4 . •Erase iPhone: Protect your privacy by erasing all the information and media on your iPhone and restoring it to its original factory settings. Erase iPhone also removes your credit and debit cards used for Apple Pay (iPhone 6 and iPhone 6 Plus). See Apple Pay on page 12 4 . Note: Before selling or giving away your iPhone, you should erase it completely to remove all of your personal data and turn off Find My iPhone to ensure the next owner can activate and use the device normally. Go to Settings > General > Reset > Erase All Content and Settings. See Sell or give away iPhone on page 18 0 . Charge and monitor the battery iPhone has an internal, lithium-ion rechargeable battery. For more information about the battery—including tips for maximizing battery life—see www.apple.com/batteries . WARNING: For important safety information about the battery and charging iPhone, see Important safety information on page 17 2 . Charge the battery. Connect iPhone to a power outlet using the included cable and USB power adapter. Note: Connecting iPhone to a power outlet can start an iCloud backup or wireless iTunes syncing. See Back up iPhone on page 17 7 and Sync with iTunes on page 18.
Chapter 3 Basics 45 You can also charge the battery by connecting iPhone to your computer, which also allows you to sync iPhone with iTunes. See Sync with iTunes on page 18. Unless your keyboard has a high- power USB 2.0 or 3.0 port, you must connect iPhone to a USB 2.0 or 3.0 port on your computer. Important: The iPhone battery may drain instead of charge if iPhone is connected to a computer that’s turned off or is in sleep or standby mode. See proportion of battery used by each app. Go to Settings > General > Usage, then tap Battery Usage. The battery icon in the upper-right corner shows the battery level or charging status. To display the percentage of battery charge remaining, go to Settings > General > Usage. When syncing or using iPhone, it may take longer to charge the battery. Important: If iPhone is very low on power, it may display an image of a nearly depleted battery, indicating that iPhone needs to charge for up to ten minutes before you can use it. If iPhone is extremely low on power, the display may be blank for up to two minutes before the low-battery image appears. Rechargeable batteries have a limited number of charge cycles and may eventually need to be replaced. The iPhone battery isn’t user replaceable; it can be replaced only by an Apple Authorized Service Provider. See www.apple.com/batteries/replacement-and-recycling/. Travel with iPhone If you travel outside your carrier’s network area, you can avoid roaming charges by turning off voice and data roaming services in Settings > Cellular. See Cellular settings on page 17 9 . Some airlines let you keep your iPhone turned on if you switch to Airplane Mode. You can’t make calls or use Bluetooth, but you can listen to music, play games, watch videos, or use other apps that don’t require network or phone connections. If the airline allows it, you can turn Wi-Fi or Bluetooth back on to enable those services, even while in Airplane Mode. Turn on Airplane Mode. Swipe up from the bottom edge of the screen to open Control Center, then tap . You can also turn Airplane Mode on or off in Settings. When airplane mode is on, appears in the status bar at the top of the screen. Wi-Fi and Bluetooth can also be turned on or off in Control Center.
4 46 Siri Make requests Siri lets you speak to iPhone to send messages, schedule meetings, place phone calls, and much more. Siri understands natural speech, so you don’t have to learn special commands or keywords. Ask Siri anything, from “set the timer for 3 minutes” to “what movies are showing tonight?” Open apps, and turn features like Airplane Mode, Bluetooth, Do Not Disturb, and VoiceOver on or off. Siri is great for keeping you updated with the latest sports info, helping you decide on a restaurant, and searching the iTunes Store or App Store for purchases. Note: To use Siri, iPhone must be connected to the Internet. See Connect to the Internet on page 16. Cellular charges may apply. Summon Siri. Press and hold the Home button until Siri beeps, then make your request. Control when Siri listens. Instead of letting Siri notice when you stop talking, you can continue to hold down the Home button while you speak, and release it when you finish. Hey Siri. With iPhone connected to a power source (or if you’ve already started a conversation with Siri), you can use Siri without even pressing the Home button. Just say “Hey Siri,” then make your request. To turn Hey Siri on or off, go to Settings > General > Siri > Allow “Hey Siri”. If you’re using a headset, you can use the center or call button in place of the Home button. Tap to speak to Siri. Siri’s response Often you can tap the screen for additional info or further action. For hints, ask Siri “what can you do,” or tap . Depending on your request, the onscreen response from Siri often includes information or images that you can tap for additional detail, or to perform some other action like searching the web or opening a related app. Change the voice gender for Siri. Go to Settings > General > Siri (may not be available in all areas). Adjust the volume for Siri. Use the volume buttons while you’re interacting with Siri. Tap to speak to Siri. Tjsj
Chapter 4 Siri 47 Tell Siri about yourself If you tell Siri about yourself—including things like your home and work addresses, and your relationships—you can get personalized service like, “remind me when I get home to call my wife.” Tell Siri who you are. Fill out your info card in Contacts, then go to Settings > General > Siri > My Info and tap your name. To let Siri know about a relationship, say something like “Emily Parker is my wife.” Note: Siri uses Location Services when your requests require knowing your location. See Privacy on page 41 . Make corrections Want to cancel that last command? Say “cancel,” tap the Siri icon, or press the Home button. If Siri doesn’t get something right, you can tap to edit your request. Or tap again, then clarify your request verbally. Siri settings To set options for Siri, go to Settings > General > Siri. Options include: •Turning Siri on or off •Turning Allow “Hey Siri” on or off •Language •Voice gender (may not be available in all areas) •Voice feedback •My Info card Prevent access to Siri when iPhone is locked. Go to Settings > Touch ID & Passcode (iPhone models with Touch ID) or Settings > Passcode (other models). You can also disable Siri by turning on restrictions. See Restrictions on page 41 .
5 48 Phone Phone calls Make a call Making a call on iPhone is as simple as choosing a number in your contacts, or tapping one of your favorites or recent calls. Or just ask Siri to “call Bob Jones.” WARNING: For important information about avoiding distractions that could lead to dangerous situations, see Important safety information on page 17 2 . Add favorites. With Favorites, you can make a call with a single tap. To add someone to your Favorites list, tap . You can also add names to Favorites from Contacts. In Contacts, tap Add to Favorites at the bottom of a card, and tap the number to add. Delete a name or rearrange your Favorites list. Tap Edit. Return a recent call. Tap Recents, then tap the call. Tap to get more info about the call, or the caller. A red badge indicates the number of missed calls. You can also reach recent and favorite people you’ve been in contact with from the multitasking screen—just double-click the Home button. Dial manually. Tap Keypad, enter the number, then tap Call. •Paste a number to the keypad: Tap the screen above the keyboard, then tap Paste. •Enter a soft (2-second) pause: Touch the “*” key until a comma appears.
Chapter 5 Phone 49 •Enter a hard pause (to pause dialing until you tap the Dial button): Touch the “#” key until a semicolon appears. •Redial the last number: Tap Keypad, tap Call to display the number, then tap Call again. Use Siri or Voice Control. Press and hold the Home button, say “call” or “dial,” then say the name or number. You can add “at home,” “work,” or “mobile.” See Chapter 4, Siri, on page 46 and Voice Control on page 31 . For best results, speak the full name of the person you’re calling. When voice dialing a number, speak each digit separately—for example, “four one five, five five five….” For the 800 area code in the U.S., you can say “eight hundred.” Call over Wi-Fi. (Not available in all areas. iPhone 5c, iPhone 5s, or later.) To route calls over Wi-Fi, go to Settings > Phone, then turn on Wi-Fi Calling. On iPhone 6 and iPhone 6 Plus, if the Wi-Fi connection is lost, calls switch automatically to your carrier’s cellular network using VoLTE ( Voice over LTE), if available. ( VoLTE calls also switch to Wi-Fi when a Wi-Fi connection becomes available.) On earlier models, a call is dropped if you lose the Wi-Fi connection. Contact your carrier for feature availability. Call from your iPad, iPod touch, or Mac. Tap or click a phone number in Contacts, Calendar, or Safari, or from a recent contact in the multitasking screen. The device must be connected to the same Wi-Fi network and, along with your iPhone, signed into FaceTime and iCloud using the same Apple ID. Both iPhone and your other device must have iPhone Cellular Calls turned on at Settings > FaceTime. Your iPad or iPod touch must be using iOS 8; your Mac must be using OS X Yosemite. (On iPhone, make sure Allow Wi-Fi Calls is turned off at Settings > Phone > Wi-Fi Calls.) The call is made via iPhone, which must be on and connected to a cellular network. Cellular charges may apply. When someone calls Tap Accept to answer an incoming call. Or if iPhone is locked, drag the slider. You can also press the center button on your headset. Silence a call. Press the Sleep/Wake button or either volume button. You can still answer the call after silencing it, until it goes to voicemail. Decline a call and send it directly to voicemail. Do one of the following: •Press the Sleep/Wake button twice quickly. •Press and hold the center button on your headset for about two seconds. Two low beeps confirm that the call was declined. •Tap Decline (if iPhone is awake when the call comes in). Note: In some areas, declined calls are disconnected without being sent to voicemail. Respond with a text message instead of answering. Tap Message and choose a reply or tap Custom. To create your own default replies, go to Settings > Phone > Respond with Text, then tap any of the default messages and replace it with your own text. Remind yourself to return the call. Tap Remind Me and indicate when you want to be reminded.
Chapter 5 Phone 50 Take a call on your iPad, iPod touch, or Mac. Click or swipe the notification to answer, ignore, or respond with a quick message. The device must be connected to the same Wi-Fi network, and signed into FaceTime with the same Apple ID, as your iPhone. Both iPhone and your other device must have iPhone Cellular Calls turned on at Settings > FaceTime. Your iPad or iPod touch must be using iOS 8; your Mac must be using OS X Yosemite. (On iPhone, make sure Allow Wi-Fi Calls is turned off at Settings > Phone > Wi-Fi Calls.) The call is received via iPhone, which must be on and connected to a cellular network. Cellular charges may apply. Keep it quiet Want to go offline for a while? Swipe up from the bottom edge of the screen to open Control Center, then turn on Do Not Disturb or Airplane Mode. See Do Not Disturb on page 34 and Travel with iPhone on page 45 . Block unwanted callers. On a contact card, tap Block this Caller (you can see a caller’s contact card from Favorites or Recents by tapping ). You can also block callers in Settings > Phone > Blocked. You will not receive voice calls, FaceTime calls, or text messages from blocked callers. For more information about blocking calls, see support.apple.com/kb/HT5845 . While on a call When you’re on a call, the screen shows several call options. Mute your line. Or touch and hold to put your call on hold. Dial or enter a number. Use the speakerphone or a Bluetooth device. Get contact info. Make a FaceTime call.Make another call. End a call. Tap or press the Sleep/Wake button. Use another app while on a call. Press the Home button, then open the app. To return to the call, tap the green bar at the top of the screen. Respond to a second call. You can: •Ignore the call and send it to voicemail: Tap Ignore. •Put the first call on hold and answer the new one: Tap Hold + Accept. •End the first call and answer the new one: When using a GSM network, tap End + Accept. With a CDMA network, tap End and when the second call rings back, tap Accept, or drag the slider if iPhone is locked. With a call on hold, tap Swap to switch between calls or tap Merge Calls to talk with both parties at once. See Conference calls , below. Mute your line. Or touch and hold to put your call on hold. Dial or enter a number. Use the speakerphone or a Bluetooth device. Get contact info. Make a FaceTime call. Make another call.