Amanda Work Group Installation Manual

Chapter 2: Installing RDSP/x32 Boards 9
The following table shows how to set the shorting jumpers for each possible 
voice board in Amanda.
Closed means that two pins are covered/connected by the shorting jumper, 
and Open means that the two pins are not covered/connected by the shorting 
jumper. In the diagrams in this chapter, the blacked out pin positions 
represent closed positions.
T
IP:Installers often place shorting jumpers over only one pin 
when the position is Open. This does not connect the...

10 Installing [email protected]/DOS
The next table show the jumper positions graphically.
C
AUTION:Do not add or remove shorting jumpers while power is ap-
plied to the board.
A Graphical View
BoardHex
AddressJumper Positions
1300
2301
3302
4303
5304
6305 

Chapter 2: Installing RDSP/x32 Boards 11
ShowJump Utility
Brooktrout provides the ShowJump utility which also shows how to 
configure the jumpers on various types of Brooktrout boards. On Amanda, 
this utility is stored in the C:\PLATFORM directory.
To use ShowJump:
1. At a DOS prompt, type:
C:\PLATFORM\SHOWJUMP
The Brooktrout Board Jumper Configuration Utility Screen displays the 
jumper configuration for hex address 300 on boards 2108 and 4108 
(which Amanda does not support).
2. Press Page Down until...

12 Installing [email protected]/DOS
d. Press Y (to confirm the shutdown).
e. Press Y again (to reconfirm).
f. After the DOS prompt C:\AMANDA> appears, turn off the 
power.
2. Remove the computer cover and locate an available slot. A full length 
slot is needed for models 2132 and 4132.
3. Remove the back slot cover and install the voice board. If there is a rear 
card guide, slide the end of the voice board into it properly.
4. Close the computer cover and turn on the power.
C
AUTION:Use an ESD-safe...

Chapter 2: Installing RDSP/x32 Boards 13
Ports are numbered consecutively from 1 to 24. Port 1 is connected to the 
lowest addressed voice board (usually address 300). Each connector on the 
voice board is linked to your telephone switching system by a standard 4-
wire line cord to a standard RJ-14 modular jack which should represent two 
analog (single-line) extensions. 

14 Installing [email protected]/DOS
The above diagram shows the back of Amanda.
432
ModemVoice Ports
VGA CardCOM1
COM2
1/2
3/4 

Chapter 2: Installing RDSP/x32 Boards 15
The above diagram shows how the telephones, telephone switching system, 
and Amanda are connected.
Voice Ports 
    1 & 2
Voice Ports 
    3 & 4
Phone Switch Telephone
tline-R.cad 

16 Installing [email protected]/DOS 

Chapter 3:
Installing RDSP/RTNI Boards
Installation Checklist
The RDSP/RTNI two-board combination puts all the Digital Signal 
Processors (DSPs, specialized CPUs) on one board and provides an analog 
telephony interface with the other.
You must configure and install each of the following:
 An RDSP/x000 (that is RDSP/4000, RDSP/8000, RDSP/12000, 
RDSP/16000, RDSP/24000) board that provides the DSPs.
 An RTNI-xATI (that is RTNI-4ATI, RTNI-8ATI, RTNI-12ATI, 
RTNI-16ATI, RTNI-24ATI) board that provides an...

18 Installing [email protected]/DOS
NOTE:The GetTones and AccuCall Plus utilities cannot define 
dial codes while the RDSP/RTNI two-board combination is 
installed. The utilities do not know how to make MVIP 
connections to the DSP resource in order to dial. The only 
solution is to use a 232 or 432 voice board while you define 
the tones. Then you replace the 232 or 432 voice board with 
the ATI board combination.
Be sure to…
1. Configure an RDSP/x000 board:
a. Configure MVIP Streams
b. Configure the...