Home > Alpha Tool.Com.HK Limited > Grinder > Alpha Tool.Com.HK Limited Grinder ECG125 User Manual

Alpha Tool.Com.HK Limited Grinder ECG125 User Manual

Here you can view all the pages of manual Alpha Tool.Com.HK Limited Grinder ECG125 User Manual. The Alpha Tool.Com.HK Limited manuals for Grinder are available online for free. You can easily download all the documents as PDF.

Page 41

41
Limited Warranty of Alpha® Ecogrinder in the USA and Canada ONLY!Alpha  Professional  Tools®  warrants  this  product  against  defects  in  material  and workmanship for a period of 180 days from the date of original retail purchase (proof of  purchase  required).  If Alpha  Professional Tools®  receives  notice  of  such  defects during the warranty period, our obligation assumed under this warranty is limited to the repair or replacement of parts, without charge. This warranty does not apply to...

Page 42

42
For more information concerning Alpha® tool repair service, please contact the 
Alpha® regional repair centers listed below:
COMPANY HEADQUARTERS:    Alpha Professional Tools® 
     103 Bauer Drive
     Oakland, NJ 07436
Hours  of  Operation:        8:30 a.m. – 5:00 p.m. EST
Telephone Number:       201-337-3343
Toll-Free Number:      800-648-7229
FACTORY SERVICE AND 
TRAINING CENTER:     3625 W. Teco Ave., 
     Suite #5    
     Las Vegas, NV 89118
Hours  of  Operation:       7:30 a.m. – 4:00 p.m....

Page 43

43
EC DECLARATION OF CONFORMITY
Name of Manufacturer:  Alpha Professional Tools®
Address of Manufacturer: 103 Bauer Drive
   Oakland, NJ 07436
   USA
Herewith declares that:
ELECTRIC	HAND	TOOL:	 	 “Ecogrinder”
   Make:    Alpha Professional Tools®
  Type:    ECG-125/ECG-225  
-Does comply with the provisions of the Low Voltage Directive 73/23EEC amended by 
93/68 EEC and Machinery Directive 98/37/EC.
And furthermore declares that:
-The following (parts/clauses of) harmonized standards have been appli\...

Page 44

44
Figure-42
Figure-43
Manual Height Adjustment Flange Assembly
Manual Height Adjustment Flange
Flange 
NutAdjust
Screw
Lock
NutAdjust
Nut
Bottom
Pulley
 
APPENDIX A
  MANUAL HEIGHT ADJUSTMENT FLANGE ASSEMBLY
For those end-users wanting to run a different grinding wheel on their E\
cogrinder, we make 
a	manual	height	adjustment	flange	assembly.
 
1.  Follow the steps to remove the grinding wheel.  Once the grinding wheel \
is removed, 
you can now start the installation and adjustment of the manual...

Page 45

45
 3.  Place the grinding wheel on top of the adjust screw and check the air gap between 
the top of the grinding wheel and the brush assembly.  The grinding wheel should 
be adjusted so there is a 1mm air gap between the ruler and the brush ri\
ng.  Test by 
turning	the	wheel	to	make	sure	the	ruler	is	floating	on	top	of	the	brush.
 
4.	 If	 the	air	gap	 is	too	 large	 or	too	 small	 remove	 the	flange	 and	adjust	 screw.	 Turn	the	
adjust nut clockwise to raise the height of the grinding wheel or...

Page 46

46
5.	 Once	the	correct	 air	gap	 is	set,	 remove	 the	manual	 height	adjustment	 flange	assembly. 	
While holding the adjust screw and adjust nut in place, turn the locking nut towards 
the adjust nut until they meet.
 
6.	 Hand	 tighten	the	manual	 height	adjustment	 flange	assembly	 to	lock	 the	adjust	 nut	in	
place on the adjust screw.
7.	 With	 the	manual	 height	adjustment	 flange	adjusted	 correctly,	 you	can	reinstall	 with	
the	grinding 	wheel 	and 	flange	 nut.		From 	this	 point, 	you 	can...

Page 47

47
Photocopy of product registration form will be accepted.
PRODUCT REGISTRATION CARD
Model No.                  Serial No.
Company Name: ______________________________________________
Name: ______________________________________________________
Address: ____________________________________________________
City: _______________________State: ________Zip: ________________
Telephone: ___________________________________________________
Purchase Date: _______________________________________________
Dealer’s...

Page 48

Copyright © 2008 Alpha Professional Tools. All rights reserved. 
103 Bauer Drive, Oakland, NJ 07436 • 800-648-7229 • Fax: 800-286-0114www.alpha-tools.com
9/22/2010  
Start reading Alpha Tool.Com.HK Limited Grinder ECG125 User Manual

Related Manuals for Alpha Tool.Com.HK Limited Grinder ECG125 User Manual

All Alpha Tool.Com.HK Limited manuals