AllTrade Snapon 15Ga Finish Nailer 870013 User Manual

MODEL #870013
FOR CUSTOMER SERVICE
PARA EL SERVICIO
PARA EL CONSUMIDOR1-888-278-8092
Printed in Taiwan  
SNAP-ON
®IS A TRADEMARK LICENSED BY SNAP-ON
®CORP.,
U.S.A., WHICH DOES NOT MANUFACTURE OR 
DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE
DIRECTED TO:
©COPYRIGHT 2007 ALLTRADE TOOLS, LLC.
1431 VIA PLATA
LONG BEACH, CA 90810-1462 USA
870015 – 18 Gauge 2 Brad Nailer _Rev 9/6/07
15 GAUGE ANGLED FINISH NAILER
INSTRUCTION MANUALTHIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION,...

CONGRATULATIONS!
Thanks for choosing this product. Our aim is to provide you with the highest quality prod-
ucts, and we want you to be totally satisfied with your product and our Customer Service.
If any help or advice is needed, please contact us at 1-888-278-8092. When properly
cared for, this product will give you many years of satisfaction.GENERAL SAFETY RULES
READ AND FOLLOW ALL INSTRUCTIONS. Failure to fol-
low all instructions in this manual may result in severe personal injury or death.
Keep...

IMPORTANT INFORMATION ABOUT THIS MANUAL
Improper maintenance and operation are responsible for the majority of accidents
involving angled finish nailers. The largest portion of these could be prevented by
recognizing the basic safety rules and precautions. Most accidents can be avoided
if the operator recognizes a potentially hazardous situation before it happens and by
observing appropriate safety rules and procedures as outlined in this manual.
Basic safety precautions are outlined in the SAFETYportion...

Always use hearing protection to protect your ears against
hearing loss due to exhaust noise. Always wear proper safe-
ty glasses to prevent injuries to the eyes from fragments of
the work piece, defective nails or other debris caused by using the angled
finish nailer.All safety glasses must have side shields and should conform to
the requirements of the American National Standards Institute (ANSI) z87.1.
Failure to comply with this warning could lead to serious or permanent damage
to the ears as well as...

COMPONENT INSTALLATION
Never use a non-relieving air coupler with the angled
finish nailer.Always use couplers that release any built-up charge in the angled
finish nailer’s firing mechanism. A non-relieving air coupler can allow the angled
finish nailer to discharge a fastener while the tool is disconnected from the
power source. Failure to comply with this warning can result in serious or per-
manent injury or even death to the operator or to bystanders.
When selecting an air compressor, it must comply...

OPERATION IN SINGLE SEQUENTIAL ACTUATION MODE
To select the Single Sequential Actuation Mode (see
Figure 1): 
1. Press and hold the red Actuation Selector embedded
in the trigger.
2. Rotate Actuation Selector down to the Single
Sequential Actuation (T).
3. Release Actuation Selector, ensuring locking tab is
fully seated in the slot.
Ensure selector has locked into position. Ensure 
actuation process is fully understood before attempting to use angled 
finish nailer.
TO USE THE ANGLED FINISH NAILER IN...

To select Contact Sequential Actuation Mode (see Figure 2): 
1. Press and hold Actuation Selector embedded in the
trigger.
2. Rotate Actuation Selector up to the Contact
Sequential Actuation (TTT).
3. Release Actuation Selector, ensuring locking tab is
fully seated in the slot.
Ensure selector has locked into position. Ensure 
actuation process is fully understood before attempting to use angled 
finish nailer.
TO USE THE ANGLED FINISH NAILER IN CONTACT ACTUATION MODE:
1. Firmly grip angled finish nailer...

4. With work piece contact against the work piece, pull trigger. The trigger must
operate smoothly.
5. Connect air supply and set regulator for 70 psi. DO NOT load a fastener strip.
6. Select Single Sequential Actuation Operation. Check for leaks. Without pulling
the trigger, press the work piece contact against the work piece. The tool MUST
NOToperate. Holding the tool away from the work piece, pull trigger and hold
for 5 seconds. The tool MUST NOToperate. Repeat steps several times.
Without pulling...

MAINTENANCE
STORAGE OF NAILS
Always handle nail strips and their box very carefully. If the nail strips have been
mishandled, they may be out of shape or have breaks in the connecting strips. This
will cause the nails to feed poorly and possibly result in misfiring or jams in the air
nailer.
Avoid storing nails in a very humid or hot environment or place in direct sunlight. 
OVERALL MAINTENANCE OF AIR NAILER
Always disconnect the air hose from air nailer before
attempting any type of maintenance or...

TROUBLESHOOTING
Most minor problems can be resolved quickly and easily using the troubleshooting
table below. For problems that cannot be solved, contact Customer Service (toll
free) at 1-888-278-8092.
PROBLEM POSSIBLE CAUSE SOLUTION Remove the air nailer from use and schedule to have it
repaired at an authorized repair facility if the work piece contact is binding
or not moving freely. Do not attempt to repair the air nailer. Failure to com-
ply can result in malfunction of the tool and severe injury to...