Aleratec 111 HDD Copy Cruiser HighSpeed WL User Guide
Have a look at the manual Aleratec 111 HDD Copy Cruiser HighSpeed WL User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 61 Aleratec manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
www.aleratec.com15 Using the HDD Copy Cruiser High-Speed WL Main Menu Copy+Compare The “Copy+Compare” function performs a copy and compare from a source HDD to one or more target HDDs. The target HDDs must be at least as large as the source. The HDD Copy Cruiser High-Speed WL will copy every block of capacity on the source HDD. 1. Load the source HDD and the target HDDs into the HDD Copy Cruiser High- Speed WL. The system will auto-detect the hard drives. After the drives have been detected, a screen similar to the one below will be displayed. Note: Before copying be sure that the capacity of the target HDD is equal to or larger than the source hard drive. 2. Press OK to start copying. The system will auto-detect the hard drives. The following information will be displayed. ESC OK2014/10/07 09:50 3. Copy+Compare ESC OKCopy Searching Source ESC OKAnalyzing Source Partition #1 10% ESC OKCopy 50.9G 11 Ready
www.aleratec.com16 Using the HDD Copy Cruiser High-Speed WL Main Menu Copy+Compare - Continued 3. During the copy process the HDD Copy Cruiser High-Speed WL will display progress information. The amount of data remaining to be transferred (shown in gigabytes), and time will be displayed as the percentage of completion increases. Note: The copying speed, capacity and duration may vary from one source hard drive to another. 4. Once duplication is complete, a job status screen will be displayed. ESC OKPass: 11 Fail: 0 Time: 20:18 ESC OKCopy x 11 50.9 G 7:35 26% 13.5 G ESC OKCompare x 11 50.9 G 0:23 1% 937 M
www.aleratec.com17 Using the HDD Copy Cruiser High-Speed WL Main Menu Overwrite The “Overwrite” function will sanitize (wipe clean of all data) the hard disk drives connected to the HDD Copy Cruiser High-Speed WL. 1. Load up to 11 HDDs into the HDD Copy Cruiser High-Speed WL. The system will auto-detect the hard drives. Using the arrow buttons (or) select “Overwrite”. The following screen will be displayed. Note: Overwriting the entire capacity of all connected hard drives can take an extended period of time. 2. Press OK to select. The following information will be displayed. 3. Use the arrow buttons to scroll between the types of overwrite: Quick Overwrite, Full Overwrite, 3 Pass, 3 Pass with Verify, 7-Pass Overwrite, or Security Erase. A. Quick Overwrite A1. To perform a Quick Overwrite, select “Quick Overwrite” and press OK. A2. The loading pattern process for the Quick Overwrite will be displayed. ESC OK2014/10/07 09:50 4. Overwrite ESC OK[ 4. Overwrite ] 1. Quick Overwrite ESC OK[ 4. Overwrite ] 1. Quick Overwrite ESC OKQuick Overwrite Loading Pattern
www.aleratec.com18 Using the HDD Copy Cruiser High-Speed WL Main Menu Overwrite A. Quick Overwrite - Continued A3. The estimated time elapsed for the Quick Overwrite process will be displayed. A4. When the process is finished, the following screen will be shown. B. Full Overwrite B1. To perform a Full Overwrite, scroll to “Full Overwrite” and press OK. The following screen will be displayed. B2. The loading pattern process for the Full Overwrite will be displayed. B3. The estimated time elapsed for the Full Overwrite process will be displayed. ESC OKQuick Overwrite 13:30 ESC OK[ 4. Overwrite ] 2. Full Overwrite ESC OKFull Overwrite Loading Pattern ESC OKQuick Overwrite Pass: 11 Fail: 0 ESC OKFull Overwrite 13:30
www.aleratec.com19 Using the HDD Copy Cruiser High-Speed WL B. Full Overwrite - Continued B4. When the process is finished, the following screen will be shown. Main Menu Overwrite C. 3-Pass C1. To perform a 3-Pass Overwrite, scroll to “3-Pass” and press OK. The following screen will be displayed. C2. The loading pattern process for the 3-Pass Overwrite will be displayed. C3. The estimated time elapsed for the 3-Pass Overwrite process will be displayed. C4. When the process is finished, the following screen will be shown. ESC OK[ 4. Overwrite ] 3. 3-Pass Overwrite ESC OK3-Pass Overwrite Loading Pattern ESC OK3-Pass Overwrite 13:30 ESC OKFull Overwrite Pass: 11 Fail: 0 ESC OK3-Pass Overwrite Pass: 11 Fail: 0
www.aleratec.com20 Using the HDD Copy Cruiser High-Speed WL Main Menu Overwrite D. 3-Pass + Verify D1. To perform a 3-Pass Overwrite + Verify, scroll to “3-Pass Overwrite + Verify” and press OK. The following screen will be displayed. D2. The loading pattern process for the 3-Pass Overwrite + Verify will be displayed. D3. The estimated time elapsed for the 3-Pass Overwrite + Verify process will be displayed. D4. When the process is finished, the following screen will be shown. ESC OK[ 4. Overwrite ] 4. 3-Pass Overwrite + Verify ESC OK3-Pass Overwrite + Verify Loading Pattern ESC OK3-Pass Overwrite + Verify 13:30 ESC OK3-Pass Overwrite + Verify Pass: 11 Fail: 0
www.aleratec.com21 Using the HDD Copy Cruiser High-Speed WL Main Menu Overwrite E. 7-Pass Overwrite This method will write over the entire capacity of the hard drives connected to the HDD Copy Cruiser High-Speed WL seven different times. DoD 5220.22M is the Department of Defense document that discusses both Three and Seven Pass Overwrite data wiping. E1. To perform a Seven Pass Overwrite, scroll to “7-Pass Overwrite” and press OK. The following screen will be displayed. E2. The loading pattern process for the 7-Pass Overwrite will be displayed. E3. The estimated time elapsed for the 7-Pass Overwrite process will be displayed. E4. When the process is finished, the following screen will be shown. ESC OK[ 4. Overwrite ] 5. 7-Pass Overwrite ESC OK7-Pass Overwrite Loading Pattern ESC OK7-Pass Overwrite 13:30 ESC OK7-Pass Overwrite Pass: 11 Fail: 0
www.aleratec.com22 Using the HDD Copy Cruiser High-Speed WL Main Menu Overwrite F. Secure Erase The “Secure Erase” function will sanitize (wipe clean of all data) the hard disk drives connected to the HDD Copy Cruiser High-Speed WL using algorithms pro- grammed by the hard drive manufacturer. Since this function is native to the hard drive, it is very fast and reliable. Almost all modern SATA hard drives support this feature. In the rare case that Secure Erase is not supported, please use the “Over- write” function to sanitize your hard drives. F1. To perform a Secure Erase, scroll to “Secure Erase” and press OK. The estimated time elapsed for the Secure Erase process will be displayed. F2. When the process is finished, the following screen will be shown. Note: Not all hard disk drives support Secure Erase, although most modern SATA HDDs do. If any of your drives do not support Secure Erase, you will see a “Dev. Not Support” error message. ESC OK[ 4. Overwrite ] 6. Secure Erase ESC OKSecure Erase 13:30 ESC OKSecure Erase Pass: 11 Fail: 0
www.aleratec.com23 Using the HDD Copy Cruiser High-Speed WL Main Menu Utility - Show HDD Info This function will display information about the hard drives inserted into the unit. You may use the arrow buttons to select hard drives loaded into different bays. 1. With the source and target HDDs loaded use the arrow buttons (or) to select “Utility”. The following screen will be displayed. 2. Press OK to select. The following information will be displayed. 3. To display the information about the hard drives in the duplicator, select “Show HDD Info” and press OK. The following information will be displayed. Use the arrow buttons to scroll up and down to view other hard drives. ESC OK2014/10/07 09:50 5. Utility ESC OK[ 5. Utility ] 1. Show Disk Info ESC OK[ 01 ] 232G D 2500
www.aleratec.com24 Using the HDD Copy Cruiser High-Speed WL Main Menu Utility - Update System Before attempting to use this feature, please contact Aleratec Support. 1. Use the arrow buttons (or) to select “Utility”. The following screen will be displayed. 2. Press OK to select. The following information will be displayed. 3. Use the arrow buttons to scroll between the types of utilities: Update BIOS and Create Update HDD. A. Update BIOS Before attempting to use this feature, please contact Aleratec Support. A1. To perform a BIOS update, select “Update BIOS” and press OK. A2. The following information will be displayed. ESC OKSearching BIOS ESC OK2014/10/07 09:50 5. Utility ESC OK[ 5. Utility ] 2. Update System ESC OK[ Update System ] 1. Update BIOS