Home > Aleratec > Hard Disk > Aleratec 111 HDD Copy Cruiser HighSpeed WL User Guide

Aleratec 111 HDD Copy Cruiser HighSpeed WL User Guide

    Download as PDF Print this page Share this page

    Have a look at the manual Aleratec 111 HDD Copy Cruiser HighSpeed WL User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 61 Aleratec manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							www.aleratec.com5
    Precautions
    Before installing your HDD Copy Cruiser High-Speed WL, please read the 
    following.
    Installation
    Avoid placing the HDD Copy Cruiser High-Speed WL in a location subject to:
    • High humidity
    • High temperature
    • Excessive dust
    • Mechanical vibration
    • Direct sunlight
    • Electromagnetic radiation
    Power
    This product has two auto switching PSUs.
    Choose a Good Location
    1. Allow adequate clearance for moving parts.
    2. Do not place near heat sources such as radiators or air ducts, or in a place 
    subject to direct sunlight, excessive dust, mechanical vibration or shock.
    3. Disconnect the AC power cord from the outlet if the product is not used for an 
    extended period of time. 
    4. Proper care will help assure maximum product life. Improper operating 
    environment and misuse may void the warranty. 
    Operation
    Do not move the HDD Copy Cruiser High-Speed WL during operation. This may 
    cause a malfunction or other undesirable results.
    Avoid exposing the unit to sudden changes in temperature as condensation may form 
    inside the HDD Copy Cruiser High-Speed WL. Should the surrounding temperature 
    suddenly rise while the HDD Copy Cruiser High-Speed WL is on, wait at least one 
    hour before turning off the power. Operating the duplicator immediately after a 
    sudden increase in temperature may result in a malfunction.
    Transportation
    Keep the original packing materials for future moving or shipping of the HDD Copy 
    Cruiser High-Speed WL. Replacement packaging may incur charge.  
    						
    							www.aleratec.com6
    Overview
    Power Up Sequence
    During the normal power-up sequence of the HDD Copy Cruiser High-Speed WL, 
    the following information will be displayed.
    • Figure 1 shows the searching of the station head.
    • Figure 2 shows the first function.
    
    ESC
    OKAleratec
    
    ESC
    OK2014/10/07             09:50
    1. Copy  
    						
    							www.aleratec.com7
    Overview
    Main Menu
    There are eleven main menu items that can be seen in the HDD Copy Cruiser High-
    Speed WL Controller Display Panel. These are:
       
    
    ESC
    OK2014/10/07             09:50 
    1. Copy
    
    ESC
    OK2014/10/07             09:50 
    2. Compare
    
    ESC
    OK2014/10/07             09:50 
    3. Copy+Compare
    
    ESC
    OK2014/10/07             09:50 
    4. Overwrite
    
    ESC
    OK2014/10/07             09:50 
    5. Utility
    
    ESC
    OK2014/10/07             09:50 
    6. Setup
    1.
    2.
    3.
    4.
    5.
    6.
    
    ESC
    OK2014/10/07             09:50 
    7. Log Manager
    7.  
    						
    							www.aleratec.com8
    Overview
    Subfunctions
    The “Overwrite” menu has six subfunctions. These are:
    The “Utility” menu has three subfunctions. These are:
    1.  Quick Overwrite
    2.  Full Overwrite
    3.  3-Pass Overwrite
    4.  3-Pass Overwrite           + Verify
    5.  7-Pass Overwrite
    6.  Secure Erase
    1.  Show Disk Info
    2.  Update System
    3.  System Info.
    
    ESC
    OK2014/10/07     09:50 4. Overwrite
    
    ESC
    OK2014/10/07     09:50 5. Utility  
    						
    							www.aleratec.com9
    Overview
    Subfunctions
    The “Setup” menu has nine subfunctions. These are:
    1.  Copy Area
    2.  Skip Error
    3.  Erase Master
    1.1  System and Files
    1.3  Whole HDD
    4.  Unknown Format
    5.  Transfer Rate
    6.  Buzzer
    7.  Language
    9.  Advanced Setup
    10.  Restore Default
    1.4  Percentage
    3.1  Disable
    3.2  Enable
    4.1  Copy Unknown
    4.2  Skip Unknown
    9.1  Wait HDD Time
    9.2  Copy HPA Area
    6.1  Turn On
    6.2  Mute
    
    ESC
    OK2014/10/07     09:506. Setup
    7.1  English
    7.2  Chinese
    1.2  ALL Partitions
    8.  Stop Motor Time
    9.3  Adjust Clock  
    						
    							www.aleratec.com10
    Overview
    Subfunctions
    The “Log Manager” menu has one subfunction:
    1.  Advanced Function
    
    ESC
    OK2014/10/07     09:507. Log Manager
    1.1  Clear ALL Log
    1.2  Set Password  
    						
    							www.aleratec.com11
    Using the HDD Copy Cruiser High-Speed WL 
    Main Menu
    Copy
    The “Copy” function performs a copy from a source HDD to one or more target 
    HDDs. The target HDDs must be at least as large as the source. The HDD Copy 
    Cruiser High-Speed WL will copy every block of capacity on the source HDD. 
    1. Load the source HDD and the target HDDs into the HDD Copy Cruiser High-
    Speed WL. The system will auto-detect the hard drives. After the drives have 
    been detected, a screen similar to the one below will be displayed. 
    Note: Before copying be sure that the capacity of the target HDD is equal to or larger than the source hard drive. 
    2. Press OK to start copying. The system will auto-detect the hard drives. The 
    following information will be displayed. 
    
    ESC
    OK2014/10/07                          09:50 
    1. Copy 
    
    ESC
    OKCopy
    Searching Source
    
    ESC
    OKCopy 
    Analyzing Source
    
    ESC
    OKCopy              50.9G
              1 Ready
    
    ESC
    OKCopy 
    Partition #1              25%  
    						
    							www.aleratec.com12
    Using the HDD Copy Cruiser High-Speed WL 
    Main Menu
    Copy - Continued
    3. During the copy process the HDD Copy Cruiser High-Speed WL will display 
    progress information.
     
    The amount of data remaining to be transferred (shown in gigabytes), and time 
    will be displayed as the percentage of completion increases. 
    Note: The copying speed, capacity and duration may vary from one hard drive to another. 
    4. Once duplication is complete, a job status screen will be displayed.
    
    ESC
    OKPass: 1  Fail: 0
    Time: 20:18
    
    ESC
    OKCopy x 11  50.9 G
    7:35    26% 13.5 G  
    						
    							www.aleratec.com13
    Using the HDD Copy Cruiser High-Speed WL 
    Main Menu
    Compare
    The “Compare” function performs a comparison of data from the source hard drive 
    to the data on the target hard drives. 
    1. With the source and target HDDs loaded use the arrow buttons (or) to 
    select “Compare”. The following screen will be displayed. 
    2. Press OK to begin the comparison. The system will auto-detect the hard drives.  
     
     
     
     
    During the compare process, the HDD Copy Cruiser High-Speed WL will 
    display progress information. Press OK to continue.
    
    ESC
    OK2014/10/07                          09:50
    2. Compare
    
    ESC
    OKCompare 
    Searching Source
    
    ESC
    OKCompare x 11 50.9 G
    0:23             1%  937 M
    
    ESC
    OKAnalyzing Source
    Partition #1              20%
    
    ESC
    OKCompare              50.9G
              11 Ready  
    						
    							www.aleratec.com14
    Using the HDD Copy Cruiser High-Speed WL 
    Main Menu
    Compare - Continued
    3. When the comparison is completed, a job status screen will be displayed.
    
    ESC
    OKPass: 11  Fail: 0
    Time: 20:18  
    						
    All Aleratec manuals Comments (0)

    Related Manuals for Aleratec 111 HDD Copy Cruiser HighSpeed WL User Guide