AIPTEK Pocketcinema N100 Users Manual

User’s Manual  
             Page 1
EN 
Welcome   Thank you very much for purchasing this product. Before you start, you are 
recommended to read this manual step by step to obtain the best results with your 
new Pico projector. We wish you enjoy it.   
 
About the product 
 
This is the latest generation of Pico projector with DLP technology inside. Known for 
great cinema projectors, the DLP technology provides rich colours and enhances the 
contrast of the image. The Pico projector offers versatile...

User’s Manual  
             Page 2
EN 
15.  Both product and user’s manual are subject to further improvement or supplement 
without further notice. 
 
Care and Safety Information for Pico Projectors 
 
1.  Avoid facing directly into the projector’s lens. 
2.  During the operation, this product may heat 
lightly, which is normal. 
3.  The device should not be used in a very dusty 
environment. Dust particles and other foreign 
objects may damage the unit. 
4.  Do not expose the device to extreme...

User’s Manual  
             Page 3
EN 
FCC Compliance Statement:  
This device complies with Part 15 of the FCC Rules. Operation is 
subjected to the following two conditions: (1) this device may not 
cause harmful interference, and (2) this device must accept any 
interference received, including interference that may cause 
undesired operation. 
 
This equipment has been tested and found to comply with limits for a Class B digital 
device, pursuant to Part 15 of the FCC rules. These limits are...

User’s Manual  
             Page 4
EN 
Table of Content 
About the Product, Safety Notice 
1 
Package Content 
4 
Knowing Your Device 
5 
Getting Started 
7 
Projecting from External Video Input Source 
8 
HDMI, VGA 
9 
Smartphone & Tablets 
12 
Charging the external mobile devices 
12 
Trouble Shooting 
13 
Specifications 
14 
 
 
 
 
 
 
Package Content 
 Please check if the following items are located in your packaging: 
 
Pico Projector 
Power Adapter 
Exchangeable Power Plug 
Remote Control...

User’s Manual  
             Page 5
EN 
   
Knowing your Device  
Projector 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Control Panel 
 
 
 
 
 
 
 
 
 
Menu
OK
DownExit 
Infrared Receiver 
DC IN HDMI / MHL ConnectorUSB Connector (for Mobile Charging)
Tripod Socket 
Speaker Connector Focus Lever  Projection Lens 
Speaker 
Keypad 
Ventilation 
VGA Port 
Ventilation 
Power
Source(External video input)
Up 
Left 
/Aspect ratioRight /   
Scene mode
Downloaded From...

User’s Manual  
             Page 6
EN 
Remote Control 
 
 
 
Installing the Remote Control Battery 1.  Remove the battery holder by holding down the side 
releasefirmly and pulling out the battery holder.   
 
2.  Insert a CR2025 coin cell battery and align the polarity correctly 
according to the marking in the battery holder. 
 
Note:  When you use the remote control for the first time, there is 
a plastic sheet between the battery and its contact. 
Remove the sheet before use.   
 
3.  Insert the...

User’s Manual  
             Page 7
EN 
Operating Range with Remote Control 
 
 
Note:  Actual operating range may slightly differ from the diagram. Additionally, a weak 
battery reduces or eliminates the operating range of the remote control. 
 
Getting Started  Charging the product The projector is built in a Li-Polymer battery for 
mobile use. Please charge the projector for 8 
hours prior to its first use. Repeat charging will 
take around 4 hours. The battery will be charged 
only when the projector...

User’s Manual  
             Page 8
EN 
Adjusting the Focus according to distance    
Place the projector on a flat surface and 
toward a wall or a projection screen. The 
projectional distance and projectional size are:   
 
Distance    : 50 cm ~ 425 cm (20 ” ~ 167 ”) 
Image size: 36 cm ~ 305 cm (14 ” ~ 120 ”)   
 
Adjust the focus by turning the Focus Lever 
upward or downward to get a sharp and clear 
picture.  
 
Note: Use a tripod (not included) to increase the height of the projectional image when...

User’s Manual  
             Page 9
EN 
HDMI  
 
Use the HDMI cable to connect the HDMI port 
on the rear panel of the projector to the external 
HDMI signal source. After connected, the 
screen switches to HDMI source automatically. 
 
 
 
 
 
 
 
 
 
 
 
 
VGA  
 
Use a VGA cable to connect the VGA port on 
the rear panel of the projector to the external 
VGA signal source. After connected, press the 
Source button on the remote control or control 
panel to select VGA source. 
 
Note: VGA cable is not...

User’s Manual  
             Page 10
EN 
Changing Playback Setting for External Video Source   
 
Press /Menu on control panel or remote control to enter the playback setting.   
 
    
     
1. Aspect ratio 
 
When the video file is in 4:3 aspect ratio, this function allows you to adjust 
how the image should appear on the 16: 9 screen. 
 
Press ◎/OK to display the options.     
1)  Pan & Scan: the image is scaled up to fit to 16:9 screen.   
2)  Letterbox: the image is displayed by original aspect...