Home > Aimco Brakes > Monitors > Aimco Brakes Monitor UEC4800TP Instruction Manual

Aimco Brakes Monitor UEC4800TP Instruction Manual

Here you can view all the pages of manual Aimco Brakes Monitor UEC4800TP Instruction Manual. The Aimco Brakes manuals for Monitors are available online for free. You can easily download all the documents as PDF.

Page 81

“User name” and “password”.  Since the controller only contains one password (one user) the “User 
name” can be left blank.  Once the password is entered it is returned to the controller were it will be 
checked and if it is correct the parameters are saved.  If it is incorrect the controller will request it from 
the bro wser again.  
After a password has been entered most browsers will cache it and return on subsequent request without 
prompting the user.  So as long as the browser is not closed it...

Page 82

5. Controller Name:   Optional variable that is passed through the Op en protocol connection. 
To set up a serial port for Open protocol set the function on the desired COM port to “Open Protocol” and 
cycle the power on the controller.  
The Controller supports the following MIDs.  See the latest Open protocol specification for  details on 
each MID.  
 
 
MID Description Note 
0001 Communication start  
0003 Communication stop  
0010 Parameter set numbers upload request  
0018 Select Parameter set...

Page 83

19.1.5 AIMCO Database  
The controller has the ability to send rundown data to an AIMCO data collection server.  Once the 
controller is on the local network there are two parameters that must be set to store data correc tly on the 
server.  
1.  Server IP Address:   This is the IP address of the AIMCO data collection server.   If the server is 
on another subnet you will also have to verify the gateway in the Ethernet settings. 
2.  Server Port Number:   This is the TCP port the server is listening on...

Page 84

 Controller Inputs 
 Bits
 15  14  13  12  11  10  9  8  7  6  5  4  3  2  1  0 
Address 1024 Handshake      Abort Enable Process number 
 
Bit name Function 
0-7 Process Number Process number input.  The enable must be off to change the Process 
Number.  On a change to the Process Number  the batch is also reset. 
8 Enable On the rising edge of Enable the tool will be enabled. 
9 Abort If Abort is on the tool will be disabled. 
10 Not used  
11 Not used  
12 Not used  
13 Not used  
14 Not used  
15...

Page 85

Byte Bit Name Function 
0 
0 Tool Enable The enabled state of the tool. 
1 Tool Ready On if the tool is ready to run.  Will be off if tool is disabled or there is 
a fault on the controller. 
2-7 Not used  
1 0 
Status OK Rundown status on for an accept. This bit is timed and will be on for ½ 
second.
 
1 Status NOK Rundown status on for a reject. This bit is timed and will be on for ½ 
second. 
2 
Msg Received On to indicate a message has been received from the MKS module and 
the inputs have changed....

Page 86

 
 
 
 
 
 
 
Byte Bit Name Function 
0 0-7 PSET Set the active parameter set of 1-32.  If 0 the active parameter set is 
left unchanged.  
1 0 
Tool Enable If PLEC Enable is 0 this input is ignored.  If PLC Enable is 1 this 
bit can be used to enable or disable the tool.
 
1-3 Not used  
4 Pause Setting Pause to 1 cause the light stack to strobe.  Setting it to 0 put 
the light stack back into its normal operation.  
5 
White Flash Setting White Flash to 1 cause the light stack to flash the white...

Page 87

19.3 Data Output Settings  
The use of Ethernet or ot her field busses requires that the data output settings of the UEC -4800 are 
configured correctly.  This can be done from either the UEC -4800 front panel or the setup software.    
UEC Data Output Settings 
Field Value Meaning 
UEC No 01 UEC Identifier Number 
Out Movement 0 Output all data through RS232C 
Output Form 0 #-CR 
Comm Speed 1 9600 bps 
Bit 1 8 bit 
Stop 0 1 bit 
Parity 0 No parity 
Torque Val Trans 1 Output 
Pulse Numb 1 Output...

Page 88

 
 
19.3.2  Data Output Configuration from PC  
1)   Turn on the UEC -4800 and wait for self- diagnosis check to finish.  
2)   Connect the front PC port on the UEC -4800 to a PC with the UEC -4800 setup software using 
a straight serial cable . 
3)   Start the setup software on the pc.   
4)   Go to ‘Main Menu’ (F12) and then ‘File Selection’ (F1) and select your configuration file or 
create a new one.   
   If a settings file is not present or settings need to be downloaded then proceed to 
the next...

Page 89

6)  Check that the settings match the settings below. If not then change the appropriate 
settings.  
7)   Click ‘Send’ to send new  parameters to the UEC -4800.  
 
Data Output Settings Menu  
19.3.3 Downloading/Importing UEC -4800 Settings 
The settings on the UEC -4800 can be downloaded from the device using the PC setup software.  If a tool 
hasn’t been selected under Main Menu   Tool Selection th en some of these menu items may be 
disabled.  
1)  Connect the front PC port on the UEC -4800 to a PC...

Page 90

 
 
 
Set Menu – Where to download/import UEC -4800  Settings 
 
20.  Light Tower Color Definitions 
UEC - LIGHT ASSIGNMENT FOR LIGHT TOWER AND KEY BYPASS 
Light Color Judgment Assignment 
Green   Accept  UEC 
Red High Torque UEC 
Red Flashing  Fault other than High Torque, Pulse 
Count, and Angle Errors  UEC 
Yellow High Pulse/Angle UEC 
Yellow Flashing  Low Pulse/Angle   UEC 
Blue Bypass Key Bypass 
White   Tool Enabled   UEC 
White Flashing  Open   External 
Lights Strobe  Open  External  
Start reading Aimco Brakes Monitor UEC4800TP Instruction Manual

Related Manuals for Aimco Brakes Monitor UEC4800TP Instruction Manual

All Aimco Brakes manuals