Home > Aimco Brakes > Torque Measurement > Aimco Brakes Freedom3 PRW Sqnet User Manual

Aimco Brakes Freedom3 PRW Sqnet User Manual

Here you can view all the pages of manual Aimco Brakes Freedom3 PRW Sqnet User Manual. The Aimco Brakes manuals for Torque Measurement are available online for free. You can easily download all the documents as PDF.

Page 61

 
 
   [email protected]     
61  
 
Using the combo box highlighted in the screenshot, select the route to send to Freedom³. 
 
 
 
STEP -6- 
Once selected the route, all the operation that belong to the route will appear in the window: 
 
 
 
 
 
Click on the “green arrow” to send the route to Freedom³ PRW 
Note: the “green arrow” is used to receive data-results also. 
 
 
STEP -7- 
 
On the right side of the window (Freedom³ interface PROD), user can see the status of data 
transfer....

Page 62

 
62 
 
62 PRW mode working with SQnet FTA 
 
STEP -8- 
After the message “Data sending completed” is appeared on “Logs” windows, it’s possible press 
“ESC” button on Freedom³. 
The wrench will restart automatically in synchronization menu: 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Press “Exit” to go back to main menu. 
 
Now Freedom³ is ready to work with route. See paragraph “:ow to run test from route - Freedom³ 
PRW” to execute test or tightening program. 
 
          
How to run test from route - Freedom³ PRW...

Page 63

 
 
   [email protected]     
63  
 
 
=f enabled, Freedom³ will ask for “=nput Vin number” before to proceed. (See PRW setup 
paragraph, to enable it): 
 
 
  
 
 
 
 
 
 
 
 
 
 
 
Type the Vin Number and press “OK” than Freedom³ will open the “Select Program” page. 
 
 
 
=n “Select Program” page is possible to select  from which operation user will start. 
 
 
 
 
 
 Operations 
 
 
 
 
 
 
 
 
 
 
 
Once the program is select press confirm on Freedom³ keyboard, the wrench is ready: 
 
 
 
  

Page 64

 
64 
 
64 PRW mode working with SQnet FTA 
       Number of test to do 
 
 
Operation name    
   Target and  
  tolerance  
    limits 
 
Units of measurements 
 
    Progression  
    bar 
 
 
 
 
     Message for operator 
 
 
Now operator can start to tighten up the target. 
 
 
 
 
If the torque and angle results will be in side tolerance limits, Freedom³ will display torque and 
angle value with green color. Otherwise, if torque or angle are outside of tolerance limits, the out 
value will be...

Page 65

 
 
   [email protected]     
65  
 
 
 
 
 
If enabled, Freedom³ will ask for “=nput Vin number” before to proceed. (See PRW setup 
paragraph, to enable it): 
 
 
 
 
 
 
 
 
 
 
 
 
 
Type the Vin Number and press “OK” then Freedom³ will open the “Select Hob” page: 
 
 
=n the example above there is only one “Hob”, user can create more jobs in a route. 
 
Once the “Hob” is selected press confirm on Freedom³ keyboard to start the job. 
Depending from the sequence of every single operation (see...

Page 66

 
66 
 
66 PRW mode working with SQnet FTA 
 
During the tightening operation Freedom³ will show the test interface: 
 
 
 
 
  
 
When the Hob is finished, push on “ESC” keyboard button, to go back to main menu or select 
another job. =t’s also possible repeat the same job, Freedom³will store all data-results in the 
memory. For every test Freedom³ save data-results and curves (Torque/Time, Torque/angle). 
See paragraph “Freedom³ PRW “:ow to send data-results to SQnet”” 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  

Page 67

 
 
   [email protected]     
67  
Freedom³ PRW “How to send data results to SQnet FTA” 
 
 
 
 
STEP -1- 
To send back data results  to SQ-Net user must connect Freedom³ to PC by USB cable 
 
             
             
             
        
        
        
       
        
        
        
  
 
STEP -2- 
Once USB cable is connected to computer and Freedom³, switch on Freedom³ and from the main 
page select “Synchronize” icon. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
USB CABLE  

Page 68

 
68 
 
68 PRW mode working with SQnet FTA 
STEP -3- 
A new window will appear, touch the button “USB/Radio” to start the synchronization: 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Subsequently  user must confirm synchronization, pushing confirm button on Freedom³ keyboard: 
 
 
 
 
 
 
 
 
 
 
After selection, Freedom³ will start the synchronization modality: 
  

Page 69

 
 
   [email protected]     
69  
 
 
The wrench is waiting for communication with SQnet 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  

Page 70

 
70 
 
70 PRW mode working with SQnet FTA 
STEP -4- 
On PC, in the SQ-Net main page, click on Freedom³ interface (PROD) icon: 
 
 
        
             
             
  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
Start reading Aimco Brakes Freedom3 PRW Sqnet User Manual

Related Manuals for Aimco Brakes Freedom3 PRW Sqnet User Manual

All Aimco Brakes manuals