Aimco Brakes Freedom3 PRW Sqnet User Manual

							 
 
   [email protected]     
61  
 
Using the combo box highlighted in the screenshot, select the route to send to Freedom³. 
 
 
 
STEP -6- 
Once selected the route, all the operation that belong to the route will appear in the window: 
 
 
 
 
 
Click on the “green arrow” to send the route to Freedom³ PRW 
Note: the “green arrow” is used to receive data-results also. 
 
 
STEP -7- 
 
On the right side of the window (Freedom³ interface PROD), user can see the status of data 
transfer. 
 
 
 
 
 
 
 
 
 
 
 
 
When Freedom³ finishes to receive the route on the last row of “Logs” window will appear the 
message “Data sending completed” (see above the picture ). 
  
						

							 
62 
 
62 PRW mode working with SQnet FTA 
 
STEP -8- 
After the message “Data sending completed” is appeared on “Logs” windows, it’s possible press 
“ESC” button on Freedom³. 
The wrench will restart automatically in synchronization menu: 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Press “Exit” to go back to main menu. 
 
Now Freedom³ is ready to work with route. See paragraph “:ow to run test from route - Freedom³ 
PRW” to execute test or tightening program. 
 
          
How to run test from route - Freedom³ PRW - 
 
 
From main page of Freedom³ is possible to choose the type of test to run “Select Program” or 
“Select Hob”. 
Select Program -> If user wants select the operation to run one by one without following any 
sequence 
Select Job -> If user wants to follow a sequence of operation or only have a specific part of route 
test (group 
Select Program 
On main page of Freedom³ touch “Select Program”: 
 
 
 
  
						

							 
 
   [email protected]     
63  
 
 
=f enabled, Freedom³ will ask for “=nput Vin number” before to proceed. (See PRW setup 
paragraph, to enable it): 
 
 
  
 
 
 
 
 
 
 
 
 
 
 
Type the Vin Number and press “OK” than Freedom³ will open the “Select Program” page. 
 
 
 
=n “Select Program” page is possible to select  from which operation user will start. 
 
 
 
 
 
 Operations 
 
 
 
 
 
 
 
 
 
 
 
Once the program is select press confirm on Freedom³ keyboard, the wrench is ready: 
 
 
 
  
						

							 
64 
 
64 PRW mode working with SQnet FTA 
       Number of test to do 
 
 
Operation name    
   Target and  
  tolerance  
    limits 
 
Units of measurements 
 
    Progression  
    bar 
 
 
 
 
     Message for operator 
 
 
Now operator can start to tighten up the target. 
 
 
 
 
If the torque and angle results will be in side tolerance limits, Freedom³ will display torque and 
angle value with green color. Otherwise, if torque or angle are outside of tolerance limits, the out 
value will be displayed with red color. In case torque and angle are out of tolerance limits, both 
will be displayed with red color. 
 
=n case of “Not OK” result Freedom³ will display a message “Confirm” pushing confirm button on 
keyboard or “Discard” pushing left arrow on keyboard. 
 
 
Select Job 
One of the option available with Freedom³ is to wok using “Hob”. The work with Hob, user must 
send from SQnet a route with job\s (group\s) inside, see paragraph “how to create a route”. 
 
From main page of Freedom³, touch “Select Hob” 
 
 
 
 
 
 
 
 
 
  
						

							 
 
   [email protected]     
65  
 
 
 
 
 
If enabled, Freedom³ will ask for “=nput Vin number” before to proceed. (See PRW setup 
paragraph, to enable it): 
 
 
 
 
 
 
 
 
 
 
 
 
 
Type the Vin Number and press “OK” then Freedom³ will open the “Select Hob” page: 
 
 
=n the example above there is only one “Hob”, user can create more jobs in a route. 
 
Once the “Hob” is selected press confirm on Freedom³ keyboard to start the job. 
Depending from the sequence of every single operation (see paragraph, how create a route) 
Freedom³ will start the job from first operation and the operator must follow the sequence 
specified in the job. When all operation complete last “screw” of last operation Freedom³ will 
display the message “Hob completed”.  
						

							 
66 
 
66 PRW mode working with SQnet FTA 
 
During the tightening operation Freedom³ will show the test interface: 
 
 
 
 
  
 
When the Hob is finished, push on “ESC” keyboard button, to go back to main menu or select 
another job. =t’s also possible repeat the same job, Freedom³will store all data-results in the 
memory. For every test Freedom³ save data-results and curves (Torque/Time, Torque/angle). 
See paragraph “Freedom³ PRW “:ow to send data-results to SQnet”” 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
						

							 
 
   [email protected]     
67  
Freedom³ PRW “How to send data results to SQnet FTA” 
 
 
 
 
STEP -1- 
To send back data results  to SQ-Net user must connect Freedom³ to PC by USB cable 
 
             
             
             
        
        
        
       
        
        
        
  
 
STEP -2- 
Once USB cable is connected to computer and Freedom³, switch on Freedom³ and from the main 
page select “Synchronize” icon. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
USB CABLE  
						

							 
68 
 
68 PRW mode working with SQnet FTA 
STEP -3- 
A new window will appear, touch the button “USB/Radio” to start the synchronization: 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Subsequently  user must confirm synchronization, pushing confirm button on Freedom³ keyboard: 
 
 
 
 
 
 
 
 
 
 
After selection, Freedom³ will start the synchronization modality: 
  
						

							 
 
   [email protected]     
69  
 
 
The wrench is waiting for communication with SQnet 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
						

							 
70 
 
70 PRW mode working with SQnet FTA 
STEP -4- 
On PC, in the SQ-Net main page, click on Freedom³ interface (PROD) icon: