ADT Security Services Safewatch Pro 3000 Entrepreneur 3000 User Manual

							– 31 –
6HFXULW\&RGHV	$XWKRULW\/HYHOV&RQW
+RZ7R$VVLJQ8VHU&RGHVDQG$WWULEXWHV
The following lists the various command strings for adding user codes and attributes.
Refer to the User Setup chart at the back of this manual for factory
assignments of user attributes and to keep a record of user programming.
NOTE: Partition Master codes apply only to those user numbers previously assigned
(by the system master/installer) to the partition master’s partition.
Add User Code: 
 System/Partition Master code + [8] + user no.
 + new user’s code
(Users 03/33 are presetUser 01 = installer User 03 = partition 1 master
to partition masters,User 02 = master User 33 = partition 2 master
but can be changed.)The Touchpad beeps once to confirm that new user was added.
Delete User Code:  System/Partition Master code + [8] + [user no.] + [#] [0]
The user code and all attributes* programmed for this user number,
including any associated RF keys, are erased from the system.
(*except assigned partition)
Authority Level:  System/Partition Master code + [8] + [user no.] + [#] [1]+ auth. level
Factory Assignments:Authority Levels (see definitions on previous page):
users 04-32/34-49 = 00 = standard user  3 = duress
users 03/33 = 41 = arm only  4 = partition master
2 = guest
Access Group: System/Partition Master Code + [8] + [user no.] + [#] [2]+ group (1-8)
Factory Assignments: noneYou can assign users to a group, then set an access schedule that
defines the times this group of users can operate the system. The
system ignores these users outside the scheduled times.
User’s Partition:  System Master Code + [8] + [user no.] + [#] [3]+ 0 + partition(s) + [#]
Factory Assignments:This command assigns the partitions the user can access. If more than
Part. 1 = users 03-32one, enter partition numbers sequentially, then press [#] to end.
Part. 2 = users 33-49E.g., master code + [8] + [user no.] + [#] [3] + [0] + [1] [2] + [#] gives
the user access to partitions 1 and 2 and the common partition.
Partition Entries: 1 = partition 1 and common
2 = partition 2 and common
3 = common partition only
RF User Number: System/Partition Master Code +  [8] + [user no.]  + [#] [4]+ zone no.
Factory Assignments: noneUse this command to assign a wireless button device (keyfob) to this
user (keyfob must be enrolled in system first; see installer).
Z
one number:  enter the zone number assigned to a button on the
keyfob that will be used for arming/disarming by this user.
Pager On/Off:
 System/Partition Master Code +  [8] + [user no.]  + [#] [5] + 0 or 1
Factory Assignments:You can program a user so that a message is sent to a pager
users 01-04 = 0 (off)whenever this code is used to arm or disarm the system.
users 05-49 = 1 (on)Paging On/Off: 1 = allow paging; 0 = no paging for this user 
						

							– 32 –
$FFHVVLQJ2WKHU3DUWLWLRQV
*272&RPPDQGDQG0XOWL3DUWLWLRQ$UPLQJ
$ERXW$FFHVVLQJ3DUWLWLRQV
Each touchpad is assigned a default partition for display purposes, and will show only
that partitions information.
·If the user is authorized, a touchpad in one partition can be used to perform
system functions in the other partition by using the GOTO command. Refer to
the GOTO section.
·If the user is authorized, that user can arm other partitions. Refer to the Multi-
Partition Arming section.
The following table shows the relationship of the touchpads in each partition when
system is armed and disarmed.
PARTITION 1 PARTITION 2 COMMON ZONE
(LOBBY, etc.)
Arming
StateTouchpad
Status
Arming
 State
Touchpad
Status
Arming
StateTouchpad
Status
DisarmedPartition 1
OnlyDisarmed
Partition 2
OnlyDisarmed Common Zone
Only
DisarmedPartition 1 and
Common ZoneArmed
Partition 2
OnlyDisarmed Common Zone
Only
ArmedPartition 1
OnlyDisarmed
Partition 2 and
Common ZoneDisarmed Common Zone
Only
ArmedPartition 1
OnlyArmed
Partition 2
OnlyArmed Common Zone
Only
When both partitions are disarmed, the touchpad in each partition displays zone
status for its partition only. The common zone touchpad shows the status in that
zone only. See Condition 1 above.
When partition 1 is disarmed and partition 2 is armed, the touchpad in partition 1
shows the status of partition 1 and the common zone. Partition 2 will display the
status of partition 2 only. See Condition 2 above.
When partition 1 is armed and partition 2 is disarmed, the touchpad in partition 1
shows the status of partition 1 only. Partition 2 will display the status of partition
2 and the common zone. See Condition 3 above.
As long as any one of the two partitions is disarmed, the common zone will always
be disarmed. The common zone will be armed only when both partition 1 and 2 are
armed. See Condition 4 above.
Condition 1 Ö
Condition 2 Ö
Condition 3 Ö
Condition 4 Ö 
						

							– 33 –
$FFHVVLQJ2WKHU3DUWLWLRQV&RQWLQXHG
8VLQJWKH*R7R&RPPDQG
If the user is authorized, a touchpad in one partition can be used to perform system
functions in the other partition by using the GOTO command.
·You must use a Custom English touchpad to access another partition.
·Touchpads automatically return to their original partition after 2 minutes
with no touchpad activity.
1.  
          +  [*] + partition number (0,1,2,3)
(Security Code)
0 = return to touchpad’s original partition.
1 = partition 1; 2 = partition 2; 3 = common zone
The touchpad beeps to confirm the partition change.
 (-7%61)(
6)%(= 83 %61
English Display: Green LED lit
2.The touchpad remains in the new partition until
directed to go to another partition, or until it
automatically returns to the original partition.
The active partition number is displayed in the upper
left portion of screen, if the option is programmed. (-7%61)(
6)%(= 83 %61
English Display: Green LED lit
0XOWL3DUWLWLRQ$UPLQJ
Some users can be given Multi-Partition arming ability by being assigned to both
partitions when programming user attributes.
When attempting to arm multi-partitions:
·You must use a Custom English touchpad.
·The system arms only if all partitions are “ready to arm.”
·If any partition is “not ready,” the system does not arm at all.
·You can use the GOTO command to bypass open zones before arming.
·If any partition is already armed when global arming is attempted, that
partition remains in its existing armed state.
  
          +  [0] + arm command (see list below)
(Security Code)
Multi-Partition Arming Commands
2 = arms all partitions AWAY
3 = arms all partitions STAY
33 = arms all partitions NIGHT-STAY
7 = arms all partitions INSTANT
1 = disarms all partitions
 (-7%61)(
6)%(= 83 %61
English Display: Green LED lit 
						

							– 34 –
$FFHVVLQJ2WKHU3DUWLWLRQV&RQWLQXHG
&RPPRQ=RQH2SHUDWLRQ
Ask your installer if a
common zone was
assigned. If so, check
this box      
Your system may have been set up to use a common zone, which is
an area shared by users of both partitions, such as a foyer or lobby.
If so, please note the following:
·The common zone will sound and report alarms only when 
both
partitions are armed. If only one partition is armed, the system
ignores faults on the common zone.
·Either partition may arm its system if the common zone is
faulted, but once armed, the other partition 
will not be able to
arm unless the common zone is first bypassed or the fault is
corrected.
·Faults on the common zone are displayed on common zone
touchpads, and will also appear on another partition’s touchpad
when that partition is armed.
·Either partition can clear and restore the common zone after an
alarm.
·Entry/exit time for the common zone is the same as for partition 1. 
						

							– 35 –
6FKHGXOLQJ
$ERXW6FKHGXOLQJ
The system provides up to 16 end-user schedules (programmable by master/installer
only), which can be used to control various types of events.
· Each schedule causes a defined event to start and stop (when appropriate) at a
specified time.
· Schedules can be set to automatically repeat at various intervals.
· Schedules can be set for random starting, if desired.
&UHDWLQJ6FKHGXOHV
1.            +  [#] + [6] [4]
(Master Code)
 (-7%61)(
6)%(= 83 %61
2.Enter a 2-digit schedule number from 01-16.
Press [*] to continue.)28)6 7,)( 23

=59-8 
3.Enter the desired 2-digit event number from the
following list.
00 = clear the scheduled event
01 = turn a programmed output on or off)28)6 ):)28
(see Using Device Commands section for a list of output device numbers used
in your system)
02 = set a user access schedule for one or more users
(see Security Codes section for an explanation of access groups)
03 = send a “latch-key” report to a pager if the system is not disarmed by a specified
time; message sent is “777-7777.”
04 = automatically arm the system in STAY mode at a specified time
05 = automatically arm the system in AWAY mode at a specified time
06 = automatically disarm the system at a specified time
07 = Display the word “REMINDER” at a specified time
Press [*] to continue.
4. For event number “01,” enter the output number
associated with this schedule.
Otherwise, this prompt is skipped.
Press [*] to continue to the “Start” prompt below.
():-) 291&)6

						

							– 36 –
6FKHGXOLQJFRQWLQXHG
5. For event number “02,” enter the access group
number. Otherwise, this prompt is skipped.
Press [*] to continue to the “Start” prompt below.+6394 291&)6
<
6. For event numbers “03-07,” enter the partition
number to be armed or disarmed.
0 = arm all; 1 = partition 1; 2 = partition 2;
3 = arm common
Otherwise, this prompt is skipped.
Press [*] to continue to the “Start” prompt.4%68-8-32
<
7. Enter the event’s start time and days of week.
Hour = 00-12; minute = 00-59
AM = 0; PM = 1
Days = Position the cursor under the desired days
using the [*] key to move forward, then press “1” to
select the day.
Press [*] to continue.78%68 718;8*7
,,11%1 
8. Enter the event’s stop time, AM/PM and days of week.
Refer to step 7 for available entries.
Press [*] to continue.7834 718;8*7
,,11%1 
9. Enter the desired repeat option.
0 = no repeat
1 = repeat schedule weekly
2 = repeat schedule biweekly (every other week)
3 = repeat schedule every third week
4 = repeat schedule every fourth week
e.g., To make a schedule that happens everyday you
would select all days with a repeat count of 1. To make
a schedule that runs for one week then stops, select
everyday with a repeat count of 0.6)4)%8 348-32
 <
10. Select the randomize option, if desired.
0 = no; 1 = yes
If selected, the schedule times will vary within 60
minutes of the “hour” time. For example, if a
schedule is set to start at 6:15pm, it will do so the
first time 6:15pm arrives, but on subsequent days it
will start anytime between 6:00 and 6:59 p.m.
Press [*] to continue.6%2(31->)

=23 
==)7 < 
						

							– 37 –
(YHQW/RJJLQJ3URFHGXUHV
$ERXW(YHQW/RJJLQJ
The system records various events in a history log, which can be viewed by the master
user using a Custom English Display touchpad.
· The Event Log holds up to 100 events.
· Events are displayed in chronological order, from most recent to oldest.
· When the log is full, the oldest event is replaced by the logging of any new event.
9LHZLQJWKH(YHQW/RJ
1.            + [#] +    6  +   0 
(Master Code)
(-7%61)(
6)%(= 83 %61
2. The system displays the most recent event as follows:
· event number
· type of event, identified by its corresponding code
(see your installer for the meaning of each code)
· zone or user number (depending on type of event)
· partition in which event occurred
· time and date of the event’s occurrence.
3. Pressing [*] displays previous events (back in time).
Pressing [#] displays events forward in time.
4. Exit the event log by pressing any key other than [*]
or [#]. ) 9 4
%1  
						

							– 38 –
(YHQW/RJJLQJ3URFHGXUHVFRQWLQXHG
7DEOHRI(YHQW/RJ&RGHV
The following table lists the codes that may appear when viewing the Event Log.
If the event code is preceded by an “E” (as in the example display on the previous
page), it means that the event is new and ongoing; if preceded by an “R,” it means the
event has been restored.
Code Definition
110 Fire Alarm
121 Duress
122 Alarm, 24-hour Silent
123 Alarm, 24-hour Audible
131 Alarm, Perimeter
132 Alarm, Interior
134 Alarm, Entry/Exit
135 Alarm, Day/Night
143 Alarm, Expansion Module
145 ECP Module cover tamper
146 Silent Burglary
150 Alarm, 24-Hour Auxiliary/Monitor
zone
162 Carbon Monoxide
301 AC Power
302 Low System Battery/Battery Test
Fail
305 System Reset (Log only)
309 Battery Test Failure
321 Bell/Siren Trouble
333 Trouble, Expansion Mod.
Supervision
341 Trouble, ECP Cover Tamper
344 RF Receiver Jam
351 Telco Line Fault
353 Long Range Radio Trouble
373 Fire Loop Trouble
374 Exit Error Alarm
380 Global Trouble, Trouble
Day/Night
Code Definition
381 RF Supervision Trouble
382 Supervision Auxiliary Wire Zone
383 RF Sensor Tamper
384 RF Sensor Low-battery
393 Clean Me
401 Disarmed, Armed AWAY,
Armed STAY
403 Schedule Arm/Disarm AWAY
406 Cancel by User
407 Remote Arm/Disarm
(Downloading)
408 Quick Arm AWAY
409 Keyswitch Arm/Disarm AWAY
441 Disarmed/Armed
STAY/INSTANT,
Quick-Arm STAY/INSTANT
442 Keyswitch Arm/Disarm STAY
570 Bypass
601 Manually Triggered Dialer Test
602 Periodic Test
606 AAV to Follow
607 Walk Test Entered/Exited
623 Event Log 80% Full
625 Real-Time Clock was Changed
(log only)
627 Program Mode Entry (log only)
628 Program Mode Exit (log only)
750 -
789Reserved for Configurable Zone
Type report codes (check with
central station when using these
codes) 
						

							– 39 –
7HVWLQJWKH6\VWHP7R%H&RQGXFWHG:HHNO\
$ERXW7HVWLQJWKH6\VWHP
Using TEST mode allows each protection point to be checked for proper operation.
·The touchpad sounds a single beep every 40 seconds as a reminder that the
system is in the Test mode.
·Alarm messages are not sent to your Customer Care Center while Test mode is on.
1  Disarm the system and close all protected windows,
doors, etc. The READY indicator light should come
on if all zones are intact (i.e., all protected windows,
doors, etc. are closed.
(-7%61)(
6)%(= 83 %61
2.            +    5   then  [0] (walk)
(Security Code)TEST
The Dial test (option “1”) is intended for the installer
and should not be used unless directed to do so by
your Customer Care Representative.
=
(-%0 =
;%0/
3. Listen. The external sounder should sound for 1
second and then turn off. If the sounder does not
sound, CALL FOR SERVICE.8)78 -2 463+6)77
 4. Fault zones. Open each protected door and window in turn and listen for three
beeps from the touchpad. Identification (zone number or zone description) of each
faulted protection point should appear on the display. The display clears when the
door or window is closed.
5. Walk in front of any interior motion detectors (if used) and listen for three beeps.
The identification of the detector should appear on the display when it is activated.
The display clears when no motion is detected.
Note that if wireless motion detectors are used, there is a 3-minute delay between
activations. This is to conserve battery life. 
						

							– 40 –
7HVWLQJWKH6\VWHP7R%H&RQGXFWHG:HHNO\
6. Test all smoke detectors, following the manufacturers instructions. The
identification of each detector should appear on the display when each is activated.
If a problem is experienced with any protection point (no confirming sounds, no
display), call for service immediately.
When all protection points have been checked and are intact (closed), there should
be no zone identification numbers displayed on the touchpad.
7. Exit test mode:
   
                + [1]
(Security Code)
If the test mode is inadvertently left active, it automatically turns off after 4 hours.
During the final 5 minutes (after 3 hours 55 minutes of Test mode), the keypad emits a
double-beep every 30 seconds to alert that the end of Test mode is nearing.