ADT Security Services Safewatch Pro 3000 Entrepreneur 3000 User Manual

							– 11 –
)XQFWLRQVRIWKH7RXFKSDGV&RQWLQXHG
6160VADT-002-V0
23
456
789
0
#
STAY
BYPASS
CHIME
INSTANTAWAY
CODETEST
READYARMED
READY
MIC MESSAGE
RECORD VOLUME
PLAY
S TAT U SFUNCTION VOICE
1211108 7
9
13 234
65 1
18
17
16
15
14
1OFF
20
19
Custom English Display Voice Touchpad
(shown without swing-down front door)
IMPORTANT!
 •When entering codes and commands, sequential key depressions must be made
within 10 seconds of one another. If 10 seconds elapse without a key
depression, the entry will be aborted and must be repeated from its beginning.
Be sure to observe this precaution when performing any of the procedures in
this manual.
•If you make a mistake while entering a security code, stop, press the [Q] key,
and then start over. If you stop in the middle while entering a code, and then
immediately start the entry over, an erroneous code might be entered. 
						

							– 12 –
(QWU\([LWHOD\V
(QWU\HOD\
Entry Delays give you time to disarm the system when you re-enter through the
designated entrance door. You must disarm the system (simply enter your security
code) before the entry delay period ends, or an alarm will occur. The touchpad beeps
during the entry delay period, reminding you to disarm the system. There are two
entry delays (if programmed). The first is for your primary entrance and the second
can be used for a secondary entrance, where a longer delay is required to walk to the
touchpad to disarm the system.
You can also arm the system with no entry delay at all by using the INSTANT
arming mode. This mode provides greater security while on the premises or while
away for extended periods of time.
See your installer for your delay times.
Partition 1
___________________________________________________________
Exit Delay:         seconds Entry Delay 1:        seconds
Entry Delay 2:       
 seconds
NOTE: Entry/Exit times set for partition 1 also apply to the common zone.
Partition 2
___________________________________________________________
Exit Delay:         seconds Entry Delay 1:        seconds
Entry Delay 2:       
 seconds
([LWHOD\
Exit delay gives you time to leave through the designated exit door without setting
off an alarm. Exit delay begins immediately after arming your system in any arming
mode and Custom Display touchpads display the message “You May Exit Now.” 
When
“You may exit now” disappears, the system is fully armed.
 If programmed, a slow beeping
will sound during the exit delay period, until the last 10 seconds, which then changes
to fast beeping (alerting you to the end of exit delay). If you cannot leave by this time,
you should stop, disarm the system, and start over to avoid a false alarm.
Exit Delay Restart (if programmed):  
If you wish to open the entry/exit door to let
someone in after arming STAY, you can re-start the exit delay at any time – simply
press the [Q
] key, then let that person in. The system automatically re-arms when
exit delay expires, which avoids having to disarm the system and then re-arm it
again. In addition, when the system is armed AWAY, reopening and closing the
entry/exit door before exit delay time expires (e.g., reentering to get a forgotten item)
will reset the exit delay time. 
						

							– 13 –
(QWU\([LWHOD\V&RQWLQXHG
([LW$ODUPV
Whenever you arm the system, the exit delay begins. If an entry/exit door or interior
zone is faulted when the exit delay ends (e.g., exit door left open), the system sounds
an alarm and starts the entry delay timer. If you disarm the system before the entry
delay ends, the alarm sound stops and the message CANCELED ALARM or CA is
displayed on the touchpad, along with a zone number indicating the faulted zone. No
message is sent to the Customer Care Center.
To clear the exit alarm condition, the open zone must be made intact; to clear the
display, enter your code plus OFF.
If you do not disarm the system before the entry delay ends, and an entry/exit door or
interior zone is still open, the alarm sound continues and an exit alarm message is
sent to the Customer Care Center. The message EXIT ALARM or EA is displayed
on the touchpad, along with a zone number indicating the faulted zone. To stop the
alarm, the system must be disarmed (your code plus OFF); to clear the display, enter
your code plus OFF a second time.
An “exit alarm” also results if an entry/exit door or interior zone is faulted within two
minutes after the end of the exit delay.
Your system may have been programmed for this feature to minimize false alarms sent to the Customer
Care Center. Ask your installer if Exit Alarm is active in your system. If so, check this box. 
               
						

							– 14 –
&KHFNLQJ)RU2SHQ=RQHV
8VLQJWKH>*@.H\WRLVSOD\DQG$QQRXQFH6\VWHP6WDWXV
Before arming your system, all protected doors, windows and other protection zones
must be closed or bypassed, otherwise the touchpad will display a Not Ready message.
1. Press [*
] READY (do not enter code first) to display
faulted zones.
2. Secure or bypass the zones displayed.
3.The touchpad’s READY indicator lights when all
protection zones have been either closed or bypassed.
4. Arm the system as desired.
Custom Display:
(-7%61)(  46)77
*
83 7,3; *%9087
English Display:
Zone no. and “NOT READY”
Voice Status: Voice Touchpads (if installed), can announce system status and faulted
zones (up to 3 zone descriptors) if the Voice Status feature is turned on.
To turn the Voice Status feature on/off: 
 #  +   0   +   2  +   4 
(also turns on Voice Chime mode; see Chime mode
 section)
To announce Status: Press [*] STATUS key once.
To announce faulted zones: Press the [*] STATUS key a second time within 5
seconds of the first press. 
						

							– 15 –
$UPLQJWKH6\VWHP
6WD\0RGH$UPV3HULPHWHU2QO\(QWU\HOD\2Q
·Used when you want to arm the system with persons staying inside (or if you have
pets that are moving throughout the premises).
·The perimeter sensors are armed, but interior sensors are left disarmed.
·Exit delay begins (you can leave through the entry/exit door, if desired).
·An alarm sounds immediately if any protected perimeter window or non-entry/exit
door is opened.
·You may otherwise move freely within the premises.
·Persons entering later can enter through an entry/exit door without causing an
alarm, but they must disarm the system within the entry delay period to avoid
sounding an alarm.
1LJKW6WD\0RGH$UPV3HULPHWHU2QO\3OXV6HOHFWHG=RQHV
·Use Night-Stay mode to provide increased security while staying inside.
·Arms same as Stay mode, but also arms pre-selected interior sensors (programmed
by your installer), while other interior sensors are left disarmed.
·Persons entering later can use an entry/exit door but they must disarm the system
and must not violate any of the programmed interior zones to avoid sounding an
alarm.
·
IMPORTANT: When Night-Stay mode is on, the selected interior zones are armed
and cause an alarm if anyone enters those areas (e.g., waking in the middle of the
night). To avoid sounding an alarm, you must disarm the system before any
activity takes place in those interior zones.
,QVWDQW0RGH$UPV3HULPHWHU2QO\(QWU\HOD\2II
·Used when staying inside and do not expect anyone to use an entry/exit door.
·Arms same as Stay mode.
·An alarm sounds immediately if any protected perimeter window or any door is
opened, including entry/exit doors.
·
IMPORTANT: Arming the system in this mode greatly increases the chance of
false alarms. Use extreme care in selecting this mode of arming.
$ZD\0RGH$UPV(QWLUH6\VWHP(QWU\HOD\2Q
·Used when nobody will be staying inside (including pets).
·The entire system (interior and perimeter) is armed.
·Exit delay begins letting you leave through the entry/exit door.
·An alarm sounds if a protected window or any door is opened, or if any movement
is detected inside your premises.
·You can reenter through an entry/exit door without causing an alarm, but you
must disarm the system within the entry delay period to avoid sounding an alarm. 
						

							– 16 –
$UPLQJWKH6\VWHP
$UPLQJ&RPPDQGV
Before arming, close all perimeter doors and windows and make sure the Ready to Arm
message is displayed.
Modes of Arming
Mode Press these keys… Touchpad Confirms By…
Stay security code + [3] (STAY)
·
 three beeps
·
 armed STAY message displayed
·
 red ARMED indicator lights
Night-Stay security code + [3] + [3]
·
 three beeps
·
 NIGHT-STAY message displayed
·
 red ARMED indicator lights
Instant security code + [7] (INSTANT)
·
 three beeps
·
 armed STAY message displayed
·
 red ARMED indicator lights
·
 also note that entry delay is turned off
Away security code + [2] (AWAY)
·
 two beeps, or, if programmed, beeping
for duration of exit delay
·
 armed AWAY message displayed
·
 red ARMED indicator lights
Leave the premises through an entry/exit
door during the exit delay period to avoid
causing an alarm. The touchpad beeps
rapidly during the last 5 seconds of the
exit delay to warn you that it is ending.
Quick Arming
If Quick Arming was programmed by the installer, the 
[#] key can be pressed in
place of the security code when arming the system in any of its arming modes.
However,
 the security code must always be used to disarm the system.
Function Key Arming
For any arming command, a function key may have also been programmed for your system. If
so, you can press and hold the appropriate function key for 2 seconds to arm the system. See
your installer for the designated functions (see Single Button Arming section).
Refer to the Accessing Other Partitions section for information on multi-partiion
arming. 
						

							– 17 –
$UPLQJWKH6\VWHP
6LQJOH%XWWRQ$UPLQJ
The “A”, “B”, “C”, and/or “D” keys on your touchpad may have been programmed for
single-button arming. Note that while it will not be necessary to use a security code
for arming, a security code must always be used to disarm the system.
If Single-Button Arming is programmed:
·A function key has been assigned to a specific type of arming: STAY mode, Night-
STAY mode, AWAY mode, or STEP-ARMING (see Step-Arming paragraph).
·You DO NOT need to enter your security code before pressing the function key
(but you always need your security code to DISARM the system).
Before arming, close all perimeter doors and windows.
1.Press and hold the assigned function key for 2
seconds (no code is required). Function keys are
shown below.
3 2 1
6 5 4
9 8 7
# 0
*READY INSTANTOFF
CODE AWAY
TEST
CHECKSTAY
BYPASS
A
B
C
D
ADT3000-007-V0
(-7%61)(
6)%(= 83 %61
English Display: 
Green LED lit
2.  The touchpad begins beeping and displays the
armed message. The red ARMED indicator also
lights.%61)(%;%=
=39 1%= )
						

							– 18 –
8VLQJWKH.H\VZLWFK
8VLQJWKH.H\VZLWFK
Your system may be equipped with a keyswitch for use when arming and disarming.
Red and green lights on the keyswitch plate indicate the status of your system as
follows:
Green Light:Lights when the system is disarmed and ready to be armed (no
open zones). If the system is disarmed and the green light is off, it
indicates the system is not ready (one or more zones are open).
Red Light:Lights or flashes when system is armed in AWAY or STAY mode.
See your installer for the meanings of the lit red light:
Lit Steady  = system armed AWAY or
system armed STAY and exit delay has expired
Flashing = system armed STAY and exit delay timer active
Rapid flashing = an alarm has occurred (memory of alarm).
Before arming, close all perimeter doors and windows.
To arm in the AWAY mode:
Turn the key to the right for 1/2 second and release.
Touchpads beep twice and the red indicator lights or
flashes.
To arm in the STAY mode:
Turn the key to the right and hold for longer than 1
second, then release. Touchpads beep three times
and the red indicator lights or flashes.
To disarm the system:
Turn the key to the right and release. The red light
turns off
GREEN
RED 
						

							– 19 –
LVDUPLQJDQG6LOHQFLQJ$ODUPV
8VLQJWKH>2))@NH\
The OFF key is used to disarm the system, silence alarm and trouble sounds, and
clear alarm memories.
IMPORTANT
: If you return and the main burglary sounder is on, 
DO NOT ENTER, but
CONTACT THE POLICE from a nearby safe location.
If you return after an alarm has occurred and the main sounder has shut itself off, the touchpad
will beep rapidly upon your entering,
 indicating that an alarm has occurred during your
absence.
LEAVE AT ONCE, and CONTACT THE POLICE from a nearby safe location.
1.            +    1
(Security Code)OFF
The “READY” indicator light will be lit if all zones
are secure, and the touchpad will emit a single tone
to confirm that the system is disarmed.
NOTE: If entry delay has started (you’ve opened the
entry door), you do not need to press the OFF key;
simply enter your security code.
(-7%61)(
6)%(= 83 %61
English Display: READY
2.To Silence a Burglary Alarm and Clear a Memory of Alarm
Enter your security code. This disarms the system and silences the alarm (or
warning tones of a Memory of Alarm).
Note the zone in alarm on the touchpad display, and make that zone intact (close
door, window, etc.). Now enter the security code plus OFF sequence again to clear
the touchpad’s Memory of Alarm display.
3. To Silence a Fire Alarm and Clear Memory of Alarm
Simply press the OFF key to silence the alarm. Note the zone in alarm on the
touchpad display, and check the detector. Now enter the security code plus OFF
sequence to clear the touchpads Memory of Alarm display. See the Fire Alarm
System section. 
						

							– 20 –
%\SDVVLQJ3URWHFWLRQ=RQHV
8VLQJWKH%