Home > ADT Security Services > Home Security > ADT Security Services Safewatch Pro 3000 Entrepreneur 3000 User Manual

ADT Security Services Safewatch Pro 3000 Entrepreneur 3000 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual ADT Security Services Safewatch Pro 3000 Entrepreneur 3000 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 68 ADT Security Services manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							– 21 –
    %\SDVVLQJ3URWHFWLRQ=RQHV
    4XLFN%\SDVV
    If programmed, Quick Bypass allows you to easily bypass all open (faulted) zones
    without having to enter zone numbers individually. This feature is useful if, for
    example, you routinely leave certain windows open when arming at night.
    1.  
              +   6 + [#]
    (Security Code)BYPASS
    In a few moments, all open zones will be displayed
    and automatically bypassed.
     Make sure that only those
    zones that you wish to leave unprotected are bypassed, and
    that there are no other zones unintentionally left open.
    (-7%61)(  46)77
     83 7,3; *%9087
    English Display: NOT READY
    2.Wait for all bypassed zones to be displayed, then arm
    the system as desired.
    Ask your installer if Quick Bypass is active for your
    system, and if so, check here: 
       
    (-7%61)( &=4%77
    6)%(= 83 %61
    English Display: BYPASS 
    						
    							– 22 –
    &KLPH0RGH
    CHIME mode alerts you to the opening of a perimeter door or window while the
    system is disarmed. When Chime mode is activated:
    ·Three tones sound at the touchpad whenever a perimeter door or window is opened.
    ·Interior zones do not produce a tone when they are faulted.
    ·Pressing the READY key will display the open protection points.
    To turn Chime Mode on/off 
    (system must be disarmed):
      
              +    9
    (Security Code)CHIME
    The CHIME message appears when on. Perimeter
    zones will cause a tone when faulted.
    The CHIME message disappears when Chime mode
    is off.
    (-7%61)(
    6)%(= 83 %61
    English Display: READY
    (-7%61)( ,-1)
    6)%(= 83 %61
    English Display: 
    CHIME
    Voice Chime: You can set the Voice Touchpads (if installed) to announce faulted
    (opened) entry/exit or perimeter zones whenever normal Chime mode is on.
    To turn Voice Chime Mode on or off: 
     #  +   0   +   2  +   4 
    (normal Chime mode must be on first)
    When Voice Chime is on, any faulted zone(s) causes a voice status announcement,
    chime and display. When off, the sounder still provides chime if normal Chime
    mode is on. 
    						
    							– 23 –
    9LHZLQJ&XUUHQWDWHDQG7LPH
    9LHZLQJWKH&XUUHQWDWHDQG7LPH
    The system lets you view its time and date setting.
      
              +[#] + [6] [3]
    (Security Code)
    OR, press the function key (A, B, C, or D) for viewing
    current date and time, if programmed.
    (-7%61)(
    6)%(= 83 %61
    English Display: 
    READY
    A typical time/date display is shown.
    The display will remain on for about 30 seconds.8-1)(%8) 7%8
    %1C
    “A”  “B” “C” “D”
            
              
              
         
    If one of the above keys has been programmed for the date/time
    display feature, place a check mark in the box beneath that key.
    6HWWLQJWKHDWHDQG7LPH
    You can set the time and date by doing the following:
    1.   
              +[#] +  [6] [3]
    (Security Code)
    (-7%61)(
    6)%(= 83 %61
    2. Press [*] when the time/date is displayed.
    A cursor appears under the first digit of the hour.
    To move cursor ahead, press [*]. To go back, press [#].
    · Enter the 2-digit hour setting.
    · Enter the 2-digit minute setting.
    · Press [1] for PM or [0] for AM.
    · Enter the last two digits of the current year.
    · Enter the 2-digit month setting.
    · Enter the 2-digit day setting.
    3. To exit, press [*] when cursor is at the last digit, or
    wait 10 seconds.
    8-1)(%8) 7%8
    41 
    Current time display
    8-1)(%8) 7%8
    4
    Time/date editing display 
    						
    							– 24 –
    3DQLF.H\V
    8VLQJ3DQLF.H\V
    Your system may have been programmed to use special keys to manually activate
    emergency (panic) functions as follows:
    This Function Sends this signal* With This Sounding…
    Silent Alarm silent alarm  no audible alarm or any visual display
    indicating that a silent alarm has been
    initiated.
    Audible Alarm audible alarm a loud, steady alarm at touchpad(s)
    and at any external sounders that
    may be connected.
    Personal Alarm auxiliary alarm steady alarm sound at touchpad(s),
    but not at external bells or sirens.
    Fire Alarm fire alarm  temporal (pulsing) sound at external
    bells and sirens.
    *All panic functions send signals to the Customer Care Center, if connected.
    To activate a Panic Function:
    Press and hold down for at least 2 seconds whichever
    lettered key on the touchpad has been programmed for
    the desired emergency function.
    OR
    Press both keys of the assigned key pair at the same
    time.
    (-7%61)(
    6)%(= 83 %61
    English Display: READY
    Typical Panic Display:
    %0%61 
    English Display:
    99 and ALARM
    A
    B
    C
    D
    6160ADT-50-002-V0
    ARMED
    READY123
    456
    789
    0
    #
    STAY
    BYPASS
    CHIME
    INSTANTAWAY
    CODETEST OFF
    READY
    6160ADT-50-003-V0
    PRESS BOTH KEYS
    OF DESIRED PAIR
    AT THE SAME TIME
    ARMED
    READY123
    456
    789
    0
    #
    STAY
    BYPASS
    CHIME
    INSTANTAWAY
    CODETEST OFF
    READY
    ZONE 96ZONE 95
    ZONE 99
    Lettered Panic Keys Panic Key Pairs
    See your installer and use the chart provided in the Features Programmed in Your
    System section to note the functions that have been programmed for your system. 
    						
    							– 25 –
    0DFUR.H\3URJUDPPLQJ	8VDJH
    $ERXW0DFUR.H\V
    The “A”, “B”, “C” or “D” keys can be used to automatically activate a series of
    commands of up to 16 keystrokes, if programmed for this function. These keystrokes,
    as a group, are called “macros” and are stored in the systems memory.
    ·Typical macro functions can include:
    - Arming sequences: STAY, Night-STAY, INSTANT, or AWAY
    - Bypassing particular zone(s)
    - Activating relay(s) for turning on (or off) lights, fans, etc.
    ·Up to four macros can be assigned – but no more than one macro to a key.
    ·Macros can be activated only by users with authority levels authorized to
    perform the macro’s function.
    NOTE: The installer must activate the desired function key (using *57 Function key
    Menu Mode) before macros can be assigned.
    See the chart at the back of this manual for the key(s) assigned for macros.
    1.  
              +  [#] + [6] + [6]
    (Security Code)
    (-7%61)(
    6)%(= 83 %61
    2.Enter the macro number, 1-4, to be programmed at
    the “Select Macro?” prompt. Remember, there are
    four macros available, but only one macro can be
    assigned to each key.7)0)8 1%63
     
    3. If a macro has been previously defined, the
    keystrokes are shown on the bottom line of the
    display, otherwise the display is blank.
    To exit this mode (and keep the existing macro
    definition), press any key except the [*] key. The
    system returns to normal mode.
    To define a macro for the selected key, press [*] and
    continue with the next prompt.1%63 (-740%=
    Enter the first of the series of desired commands, (do
    not include your user code when programming a
    macro), then press/hold the “D” key for at least two
    seconds to complete the first command. This key
    terminates each separate command, and appears as
    an “F” in the touchpad display.1%63 4+1 
    						
    							– 26 –
    0DFUR.H\3URJUDPPLQJ	8VDJHFRQW
    The touchpad beeps to acknowledge your input and
    displays the command you entered (followed by “F”).
    4. Enter the next command, followed by press/holding
    the “D” key for at least two seconds. The touchpad
    beeps and displays the keystrokes entered so far.
    5. Repeat until the all the desired commands (up to 16
    characters including the “F”s) have been entered.
    Be sure to check your keystrokes before continuing.
    If you made a mistake, you must start over.
    6. To exit, press/hold the “D” key for at least two
    seconds. The display returns to system status and
    indicates system is ready.Typical Macro Display:
    1%63 4+1
    *#**
    ([DPSOHRI0DFUR3URJUDPPLQJ
    Suppose you want to (1) bypass the two upstairs window zones, then (2) turn on an
    exterior light, and then (3) arm the security system in the AWAY mode. The
    procedures in the table that follows show you how you would program this macro:
    FunctionKeystrokes Required Touchpad Display
    1.
      Bypass zones 02 & 03Press BYPASS [6]
     key, then
    2-digit zone numbers 02 & 03.
    2.
      Insert terminator. Press the “D” key for at least 2 seconds.*
    3.
      Turn light on
          (device 01).Press [#] and 7 keys for “device ON”, and
    [01] key for selecting device 1.*
    #
    4.
      Insert terminator. Press the “D” key for at least 2 seconds.*#*
    5.
      Arm system AWAY Press AWAY [2]
     key.*#*
    6.
      Insert terminator. Press the “D” key for at least 2 seconds.*#**
    8VLQJD3URJUDPPHG0DFUR.H\
    (-7%61)(
    6)%(= 83 %61
    1.Press the Macro key programmed for the desired
    series of commands for at least 2 seconds. 
    The “Enter
    User Code” prompt appears. The prompt remains
    displayed for up to 10 seconds.
    )28)6 97)6 3()
    
    2.Enter your 4-digit user code.
    The programmed macro sequence begins
    automatically after the user code is entered. 
    						
    							– 27 –
    8VLQJHYLFH&RPPDQGV
    $ERXWHYLFH&RPPDQGV
    Your system may be set up so that it can control certain lights or other devices.
    ·Some devices may be automatically turned on or off by the system.
    ·You may be able to override automatically controlled devices using the
    commands described below.
    ·Some devices can be manually turned on or off using the commands described
    below.
    ·See your installer for a list of devices that may be set up for your system. A list
    of these devices is provided at the back of this manual for you to fill out.
    To Activate Devices:
      
              +  [#] + [7] + 2-digit device number
    (Security Code)
    Devices associated with that device number activate.
    To Deactivate Devices:
      
              +  [#] + [8] + 2-digit device number
    (Security Code)
    Devices associated with that device number deactivate.
    (-7%61)(
    6)%(= 83 %61
    English Display: 
    READY 
    						
    							– 28 –
    3DJLQJ)HDWXUH
    $ERXW$XWRPDWLF3DJLQJ
    Your system may be set up to automatically send alert messages to a pager as certain
    conditions occur in your system.
    ·The following events can be programmed by your installer to be sent to the pagers:
    arming, disarming
    †, alarms, and trouble conditions. († reports when arming/disarming
    from a touchpad using a security code; auto-arming/disarming, arming with assigned
    button, and keyswitch arming do not send pager messages.)
    ·You can also program the system to send an automatic pager message to alert you
    in the event that someone has not arrived home (disarmed the system) within a
    defined period of time (see the Scheduling section for details on programming a
    “latch key report”).
    ·Your installer programs the pager phone numbers and reporting events.
    ·The pager message consists of a 7-digit system status code that indicates the type of
    condition that has occurred.
    ·An optional, predefined 16-digit character string can precede the 7-digit system
    status code; these characters can consist of a PIN no., subscriber account no., or any
    additional data that you may wish to have sent to the pager.
    ·The pager display format is as follows:
    3-digit Event CodeÈ
    È
    Optional 16 digits Æ
    Æ AAAAAAAAAAAAAAAA – 
    BBB – 
    CCCC Å
    Å 4-digit User or Zone No.
    A = B = C =
    Optional 16-digits for
    Account numbers,
    PIN numbers, or any
    other data;
    programmed by the
    installer, if required.A 3-digit code that
    describes the event
    that has occurred
    in your system
    (see for event
    codes table below)A 4-digit User or Zone number, depending on the type of
    event that has occurred, where:
    · alarms and troubles display zone number
    · arming/disarming (opens/closes) display user number
    The first  digit indicates partition (0 = system, 1 =
    partition 1, 2 = partition 2, 3 = common), followed by the
    3-digit user or zone number.
    The 3-digit Event Codes (BBB) that can be displayed are:
    911 = 811 = 101 = 102 =
    Alarms.
    The 4-digit number
    (CCCC) following this
    code is the zone number
    that has caused the
    alarm.Troubles.
    The 4-digit number
    (CCCC) following this
    code is the zone number
    that has caused the
    trouble.Open
    (system disarmed).
    The 4-digit number
    (CCCC) that follows
    this code is the user
    number that has
    disarmed the system.Close
    (system armed).
    The 4-digit number
    (CCCC) that follows
    this code is the user
    number that has armed
    the system. 
    						
    							– 29 –
    3DJLQJ)HDWXUH
    Examples of typical 7-digit pager displays follow.
    Ex. 1
    .³ =   R eporting of an alarm (911) caused by a fault on zone 4 (0004) in
    partition 1.
    Ex. 2.³
    =  Reporting of a closing–system arming (102)– by user 5 (0005) in
    partition 2.
    $ERXW0DQXDO3DJLQJ
    Your system may be set up so you can manually send a message to up to four pagers.
    ·Your installer programs the paging function key and the pager phone numbers.
    ·Pressing the paging keys sends the message 
     
    999–9999  to the selected pager
    .
    ·This message could mean “call home”, “call your office”, or any other prearranged
    meaning.
    ·See the Paging chart at the back of this manual for details of the paging setup for
    your system.
    1. Hold 
    pager key 2 seconds then press [1-4].
    (pager no.)
    Press and hold the programmed Paging Key for at
    least 2 seconds (wait for beep), then press the pager
    number (1-4)* representing the pager intended to
    receive the message.
    2. The recipient, on seeing the 999–9999 message, will
    understand the prearranged meaning of this signal.
    * 
    If no number is pressed, the message is sent to pager 1.
    (-7%61)(
    6)%(= 83 %61
    English Display: 
    READY
    
    Pager Display
    /DWFK.H\3DJLQJ
    You can program a schedule that causes a pager report to be sent if the system is not
    DISARMED by the scheduled time (see Scheduling section, event “03”). For example,
    a working parent might want a message to be sent to a pager if their child did not
    arrive home from school and disarm the system by a certain time.
    If programmed, the message that is sent is: 
     7 7 7 –7777 . 
    						
    							– 30 –
    6HFXULW\&RGHV	$XWKRULW\/HYHOV
    $ERXW6HFXULW\&RGHV
    Your system lets you assign up to 45 different security codes for use by other users.
    ·Only the System Master and Partition Masters can assign user codes to users.
    ·Users are identified by 2-digit user numbers 03-49 and are pre-assigned to either
    partition 1 or partition 2 (users 01-02 are reserved).
    ·Only the Installer or System Master can change the partitions to which a user is assigned.
    ·In addition to a security code, each user is assigned various system attributes.
    ·User codes can be used interchangeably within a partition when performing system
    functions (a system armed with one users code can be disarmed by another users
    code), with the exception of the guest code described below.
    ·User code programming involves these steps:
    1. Choose a user number from the set of users assigned to the partition in which the
    user will be operating, and assign a 4-digit security code.
    2. Assign an authority level to that user.
    3. Assign other attributes as necessary (see attributes on the next page).
    NOTE: The factory settings are designed to meet most normal user situations.
    Therefore, the only step you usually need to do when adding users is assign a user
    number (from the partition’s pre-assigned user numbers) and a security code.
    $XWKRULW\/HYHOHILQLWLRQV
    Authority levels define the system functions a particular user can/cannot perform.
    Level Title Explanation
    N/A System Master Reserved for user 02; Can perform all system functions and assign
    codes in both partitions; can change its own code as follows:
    Master code + [8] + 02
     + new master code + new master code again
    0  Standard User Can only perform security functions in assigned partition.
    Cannot perform other system functions.
    1  Arm Only Can only arm the system. Cannot disarm or do other functions.
    2  Guest Can arm the system in assigned partitions, but cannot disarm the
    system 
    unless the system was armed with this code. This code is
    typically assigned to someone (such as a babysitter or cleaner) who
    has a need to arm/disarm the system only at certain times. The user
    of this code should 
    not use the “Quick Arming” feature.
    3  Duress Code Intended for use when you are forced to disarm or arm the system
    under threat. When used, the system will act normally, but can
    silently notify the Customer Care Center of your situation, if that
    service has been provided.
    4  Partition Master Can do everything a standard user can do, and can assign
    user codes to users in their partition. 
    						
    All ADT Security Services manuals Comments (0)

    Related Manuals for ADT Security Services Safewatch Pro 3000 Entrepreneur 3000 User Manual